20 Most Recent Kenmore 91112 / 91114 / 91117 Electric Kitchen Range Questions & Answers

Kenmore 91112 /... | Posted on Feb 19, 2018 | Be the first to answer


Try setting the clock

Kenmore 91112 /... | Answered on Sep 26, 2017

Kenmore 91112 /... | Posted on Sep 05, 2017 | Be the first to answer

Kenmore 91112 /... | Posted on Jul 10, 2017 | Be the first to answer

Kenmore 91112 /... | Posted on Jun 23, 2017 | Be the first to answer


You have either a bad burner or a bad control for same, or bad connections.

With power removed use a pair of pliers to crimp the connections (after cleaning the ones on burner) going to the burner.

Kenmore 91112 /... | Answered on Jun 17, 2017


Hello & Welcome to FixYa

Error code F10 is displayed due to electronic oven control failure and the only way to solve this problem is by replacing the control board which is bad. Sorry for the bad news but hope you understand... Please get back to me if you have any other questions.

Kevin

Kenmore 91112 /... | Answered on Feb 26, 2016




If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61

Kenmore 91112 /... | Answered on Jan 03, 2016

Kenmore 91112 /... | Posted on Oct 20, 2015 | Be the first to answer

Kenmore 91112 /... | Posted on Mar 05, 2015 | Be the first to answer


I suggest you check www.repairclinic.com
They will answer your questions and may even have a better price on the replacement glass.

I have no affiliation, but have been pleased with their service.

Kenmore 91112 /... | Answered on Mar 04, 2015


You can sometimes see the burnout of an element. In some cases it will actually burn a hole or melt a spot in the outer lining of the element. Sometimes it shows nothing. In that case it can only be tested with an ohm meter... Normal reading is approx 15 to 20 ohms. No reading at all means its burned out.

Kenmore 91112 /... | Answered on Mar 01, 2015


Assuming you've removed the door, lay it down on a blanket and look at the bottom. Usually there are 3 or 4 screws there - remove them. Then remove the 2 screws that hold the handle to the door. At this point, you should be able to separate and remove the outer door & glass panel. 90% of all your spills and drips can be cleaned at this point. I do not recommend taking the rest of the door apart, as it gets more complicated to disassemble and especially re-assemble correctly.

If you need further help, reach me via phone at https://www.6ya.com/expert/ronald_e6b9572cebe3ad27

Kenmore 91112 /... | Answered on Jan 27, 2015


This is a "feature" imposed upon us by those energy-saving freaks and environmentalist-wackos. What you need to do is press and hold the clock button for 12 to 15 seconds. When you first press this button, the display will appear. Then in about 7 or 8 seconds it will disappear. Keep holding it for 12 to 15 seconds until it re-appears. Now if you release the clock button, it should remain on.

If you need further help, reach me via phone at https://www.6ya.com/expert/ronald_e6b9572cebe3ad27

Kenmore 91112 /... | Answered on Jan 03, 2015


I think this means that the oven is over-heating - caused by a relay that is stuck closed on the Electronic Oven Control. You will have to replace that EOC.

If you need further help, reach me via phone at https://www.6ya.com/expert/ronald_e6b9572cebe3ad27

Kenmore 91112 /... | Answered on Jan 03, 2015


According to Kenmore's list of error codes, F1 means EOC (Electronic Oven Control) failure, and the solution is to replace the EOC. You might look into that. The part itself costs around $80, as far as I can see.

Kenmore 91112 /... | Answered on Nov 26, 2014

Kenmore 91112 /... | Posted on Jul 31, 2014 | Be the first to answer

Kenmore 91112 /... | Posted on May 29, 2014 | Be the first to answer

Kenmore 91112 /... | Posted on May 12, 2014 | Be the first to answer


The oven ignitor should have a resistance reading of about 3.2 to 3.6 ohms. If the readings are out of this specification or show open replace the ignitor. measure the resistance of the oven valve. The gas valve should have about 1.5 ohms of resistance. If the gas valve is OK, the control board is suspect. The ignitor needs 120vac to work.

Kenmore 91112 /... | Answered on Apr 07, 2014

Not finding what you are looking for?
Kenmore 91112 / 91114 / 91117 Electric Kitchen Range Logo

279 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Kenmore 79012 / 79014 / 79019 Gas Kitchen Range
Kenmore 79012 / 79014 / 79019 Gas Kitchen Range

396 Questions

Kenmore 95002 / 95004 Electric Kitchen Range
Kenmore 95002 / 95004 Electric Kitchen Range

149 Questions

Kenmore 78812 / 78814 / 78819 Gas Kitchen Range
Kenmore 78812 / 78814 / 78819 Gas Kitchen Range

93 Questions

Kenmore 46123 Stainless Steel Electric Kitchen Range
Kenmore 46123 Stainless Steel Electric Kitchen Range

67 Questions

Kenmore 96422 / 96424 / 96429 Electric Kitchen Range
Kenmore 96422 / 96424 / 96429 Electric Kitchen Range

74 Questions

Top Kenmore Kitchen Ranges Experts

Cindy Wells

Level 3 Expert

6220 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

Michael Thomas
Michael Thomas

Level 3 Expert

3056 Answers

Are you a Kenmore Kitchen Range Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Kenmore Kitchen Ranges

  • Kenmore Kitchen Ranges

Most Popular Question

open oven windows clean in between 2

  • Kitchen Ranges
Loading...