20 Most Recent Brother ULT2001 - Page 9 Questions & Answers

https://www.sewingonline.co.uk/library/BROTHER-VX-970.html

Request the manual from Brother

1. Button failure 2. Circuit failure

Be sure to select a compatible stitch e.g 0, 1, 4, 37, 38, or 40. See owners manual. Note reverse stitch not supported for all selections.

Try rotating hand wheel manually after stitch selection to check for interference.

personally i would take to a local repair shop. there should never be parts falling out

It's hard to give an idea about it. ch

Brother might be able to furnish one.

Request the manual from Brother.

Brother might be able to supply a diagram and/or a manual including the diagram.

USE A SHORTER TABLE FOR SEWING

IF IT WAS PLASTIC /NYLON I HAVE USED A LEFT HAND DRILL BIT AND CAREFULLY DRILL IT OUT USUALLY IT WILL UNSCREW WHILE DOING IT THEN JUST SCREW THE NEW ONE IN WWW.HARBORFREIGHT.COM SELLS THE DRILLBITS

YOU MIGHT ASK BROTHER MFG OR GOOGLE IT

If you're using the horizontal spool pin, be sure the spool is inserted onto the spool pin in the proper orientation. Per the manual; Set the thread spool on the spool pin so that the thread unwinds from the front of the spool.

Horizontal spools require the spool cap be equal or greater in size than the spool diameter. Using a smaller cap may result in the thread snagging on the spool edge.

Be sure to follow threading instructions exactly.

Always try different manufacturer thread to eliminate the possibility of weak or bad thread.

If the spool pops in, you may be able to find a replacement where sewing machine parts are sold.

If it was a molded to a platform, a thread stand may be a less expensive method to use. You can find a single cone thread stand with sewing notions.

http://www.sewingmachine221sale.bizland.com/store/page24.html/

Hi there. Try this website http://brother.manymanuals.com/

Depends what you plan to do with the machine. If you expect to do simple straight or zig-zag stitching, perhaps sewing garments or home decor items, a simple mechanical machine with a few decorative stitches may be sufficient. However, if you decide you want to get into computerized embroidery, etc., then a computerized machine with more capabilities may be a better choice. Of course, with that decision is the price. Just go with the best value for your money. If you are a beginner, perhaps a simple machine to start with may be a good choice until you advance your sewing abilities to a point when you can consider a machine with more capabilities. If you decide you really don't like sewing, at least you haven't put out a great amount of money. ...

I would check on Brother's site for your manual. https://support.brother.com/g/b/productseries.aspx?c=gb&lang=en&pcatid=36

Had the same problem here. Took it apart and found that several tracks in the ribbon cable from the keypad to the circuit board on which the LCD display is mounted were broken hence keypad needs to be replaced. Its part number is XA4331002 and available online from Sewing World. Have just finished fitting the replacement and keypad and sewing machine are working A1 OK.

Try turning unit on with foot control unplugged. If it starts on it's own with foot pedal disconnected then internal board failure (smoke).


Brother E6 error?
A.
The upper thread could be tangled. Remove the upper thread and any loose threads. Raise the pressure foot, raise the needle to its highest position and rethread the machine.
Remove the bobbin and bobbin case to clean any lint or loose threads. Install the bobbin case so that the projection on it aligns with the spring. Then install the bobbin into the bobbin case.
The needle could be bent. Replace the needle making sure the flat side is facing the back.

Appears to be the same bae machine with a slight difference in the needle position selector.


Free download the manual for the 810 at

https://www.manualslib.com/manual/219387/Brother-Vx-810.html