Elna 2007 Mechanical Sewing Machine - Answered Questions & Fixed issues
Elna 700
If your machine did not come with a little screw driver, you will need to purchase a r flat tip screw driver. Usually, you can find small screw drivers in an eye glass kits too. Take your needle, your foot, bobbin, etc. all moving parts off and set aside. Then use your screw driver to remove the bottom plate. Sometimes it could be sitting right there you might can turn your machine upside down and you should here where it's at without having to disassemble the whole bobbing casing. I hope this was helpful.
12/11/2017 2:41:37 PM •
Elna 2007...
•
Answered
on Dec 11, 2017
•
76 views
My very old Elna Super foot pedal does not always
this sounds like the internal clutch drive is worn, it probably is not the foot pedal at all. It may be possible to repair it if you can track down an Elna serviceman. My Air Electronic SU got worn internally and my serviceman was able to repair it once for me.
9/6/2017 4:00:32 PM •
Elna 2007...
•
Answered
on Sep 06, 2017
•
1,270 views
My elna sewing machine bobbin
If the fly wheel is going around then the clutch isn't disengaged to wind the bobbin, you need to pull out the flywheel on your model to disengage the clutch for bobbin winding.
Take thread from thread spool across to bobbin winder thread guide, then back to bobbin and thread the tail through the hole on top of the bobbin. Place bobbin onto spindle on top of machine and then push it against the stop to engage the bobbin winding motor. HOld the thread tail up and start winding slowly until the bobbin core has been covered including the starting point. Stop and trim off the thread tail with scissors. COntinue winding bobbin and give the thread a nudge if needed to wind evening top middle and bottom of the bobbin. A good smooth wind is important. Also don't wind at full speed and keep an eye on the thread reel that the thread is coming off, you don't want it bouncing around as this will **** the thread and stretch then relax it affecting your bobbin wind.
Obviously if you know this and the bobbin winding mechanisim is just not working, then it will need a service/replacement by an Elna repair person.
11/19/2019 9:01:11 AM •
Elna 2007...
•
Answered
on Nov 19, 2019
•
5,420 views
Threads jamming the bobbin case on elna sewing machine
Probably unevenly wound on the bobbin. Or tension needing adjusting, be careful to note where tension spring started before adjusting and do in very small increments.
Perhaps the spring has some fluff stuck on it and thread cannot slide through easily. Take out bobbin and clean
11/2/2015 9:09:15 PM •
Elna 2007...
•
Answered
on Nov 02, 2015
•
688 views
Feeder not moving
knotted up thread under the material indicates that the needle thread tension is incorrect ( needs tightening)
once you have that correct the material, will feed normally
use scrap when adjusting and the correct tension is when the top and bottom threads meet at the join ( middle -center )of the materials being sewn
9/8/2015 1:47:51 AM •
Elna 2007...
•
Answered
on Sep 08, 2015
•
201 views
Manuel elna su air electronic
I have a manual for the SU Air Electronic if you are still looking? you can email me on tallygirl98 at yahoo dot com and I'll send you a scan
2/1/2015 6:46:15 AM •
Elna 2007...
•
Answered
on Feb 01, 2015
•
299 views
Elna 2002 -
The question was regarding the Elna 2002 not 2007 and it wasn't a problem. I just do not understand how the pattern selection works. Thank you.
1/3/2015 7:32:30 PM •
Elna 2007...
•
Answered
on Jan 03, 2015
•
799 views
Elna 2007 manual
I have one as a PDF. Free.Contact me I can email the 1.2 MB file
8/22/2014 7:20:12 PM •
Elna 2007...
•
Answered
on Aug 22, 2014
•
90 views
Elna 2007 service instructions
These machines are mechanical and electrical computerized wonders. Unless you are a trained certified Technician, I don't suggest you try yo make repairs yourself. There are also many special tools and bit tips that may be required to remove the case...
Please, take it to a proper sewing machine repair shop with experienced technicians.
Cheers,
Kelly
San Diego, CA
6/16/2014 12:41:47 AM •
Elna 2007...
•
Answered
on Jun 16, 2014
•
70 views
Not finding what you are looking for?