20 Most Recent Yamata FY811 Mechanical Sewing Machine - Page 2 Questions & Answers

You need to take it into a shop for full reset

check under the feed for tnagled thread in the bobbin area and the shafts

You can get this with google.

Otherwise ask a deep web research service, like manualfox.com
- this is the hassle-less guarantee to get it.

Hi,

Please check this website :

http://www.thefind.com/crafts/browse-yamata-built-in-sewing-machine

Thanks for contacting Fixya.

Make sure the clutch motor is powering up. make sure voltage toggle switch is on 110v and not 220v. Also rotation set correctly. Independently, make sure the motor runs. With your hands and motor belt disengaged, attempt to turn the handwheel toward you. If it is moving, then make sure motor is running. It handwheel does not turn it could be the machine. Make sure the stitch length dial is set at 2 or 3 and not 0 or 5. That could be that problem as well.

User manual for yamata fu31016-01cb

try changing the needlerethread the machine top & bobbinclean under the needle plate & in the bobbin area for loose threads or lintcheck to make sure the bobbin & bobbin case is not damaged

Please help I'm am in great need I need the right needles for this machine which is a yamata FY 8500

Industrial machine, not easy. https://www.google.com/search?q=Yamata+needles ..

Watch video on YouTube for your machine. For zig zag you need to adjust stitch width. Akso where is the manual. You need a new manual to explain how to set each stitch.

This is the only one available for free

Yamata FY500-1 Manuals ' ManualsLib

https://www.manualslib.com > ... > Sewing Machine

Yamata FY500-1 Pdf User Manuals. View online or download Yamata FY500-1 Instruction Manual. these are available at a cost http://www.manuals.group/results_mm.php?brand=YAMATA&appliance=Sewing+Machine contact them direct

Yamata

https://yamata.com

Domestic Machines · Industrial Machines · Zig Zag · Coverstitch · Overlock · Lockstitch · Special Type · Motors · Cutters · Sewing Machine Tables. Site navigation .. ..

Request the manual from Yamata.

Clutch on the centre of the handwheel? Ah, it is an industrial straight stitch machine. The motor is separate. Turn the handwheel hard by hand. Then it needs re-timing. https://www.allbrands.com/products/4031-yamata-fy8500-gc8500-high-speed-straight-lockstitc ..

Q: So your brand new Yamata FY920 needle will not go when the Power Foot-Peddle is pressed. A: If it is new, there is little chance any part is worn out. The most likely cause is that the Power Train has been disengaged as if to wind a Bobbin. The Handwheel, on the Left side (the top wheel), has a slide-switch in the middle of the hub. Slide that switch in the other direction and your Power Train should now be engaged again, allowing the Needle to go Up and Down when the Power Foot-Peddle is pressed. That should do the trick to get the Needle to sew again. [ P.S. That's a nice machine, but be careful when you clean it, since the markings have been known to run if any kind of solvent, or even some plastics, come in contact with them. ] Hope this helps. Sincerely, Amender, 2020-DEC-04. #

TAKE IT TO A REPAIR SHOP LOCALLY

Here ya go! https://data2.manualslib.com/pdf5/100/9978/997726-yamata/fy5001.pdf?0d41907c7e2ee282e58f0eb4a30fa806

I had a search around and here is a website that lets you download a manual..... https://instructionsgk257-257b.blogspot.com/ Regards Geoff

Might contact a vendor to ask if you can purchase a copy of instructions. http://boxusamail.com/yamata-fy8500-gc8500-lockstitch-industrial-sewing-machine-servo-motor-table-juki-ddl-8700/