Malfunction C0500 Copier will not work anymore! Can I fix this myself?
C0500 refers to a low fuser temperature. You can attempt to clear the code by using the tech rep service mode. Go to "Counter" Go to "Trouble" Trouble reset If "warm Restart Swich" is asked for- This can be actuated through a small access hole on the right side of the control panel, using a straightened paper clip or something similar. You may need to clear the counter by pressing "clear" and then "end". After clearing the code, power cycle the copier. If it comes to "ready" you are all set. If not, you may have a blown heat lamp or thermal fuse which would need to be replaced by a technician. Good Luck!!
Posted on May 23, 2007
Requires a maintenance code. Can u help, please?
C0500 refers to a low fuser temperature. You can attempt to clear the code by using the tech rep service mode.
Go to "Counter"
Go to "Trouble"
Trouble reset
If "warm Restart Swich" is asked for- This can be actuated through a small access hole on the right side of the control panel, using a straightened paper clip or something similar.
You may need to clear the counter by pressing "clear" and then "end".
After clearing the code, power cycle the copier. If it comes to "ready" you are all set. If not, you may have a blown heat lamp or thermal fuse which would need to be replaced by a technician. Good Luck!!"
Posted on Oct 31, 2007
copier does not work all that i see is the call a tech light and this error code. Have noticed others with similar codes on other konica minoltas and the problem being low fuser teampature. where is the fuser? and how do i fix?
I have a Konica Minolta CSPRO EP1054 (in the Middle East)
I accidentally plugged the EP1054 copier into a 110V outlet instead of
the 220V. Immediately the malfunction code (error code) of "C05"
appeared along with the "Call Tec Rep" indicator light (wrench).
I followed the instructions posted by "Soul Visitor" ... i.e., I found
the "Trouble Reset Switch" (not shown in the user manual) by opening
the upper back panel and pressing the small black button in the lower
right hand corner of the middle circuit board (green).
It worked perfectly!
Posted on Jan 16, 2009
I'm getting error code C0500 on my Minolta. Your posted fix for this problem was as follows:
C0500 refers to a low fuser temperature. You can attempt to clear the code by using the tech rep service mode.
Go to "Counter"
Go to "Trouble"
Trouble reset
If
"warm Restart Swich" is asked for- This can be actuated through a small
access hole on the right side of the control panel, using a
straightened paper clip or something similar.
How do I get to Tech Service mode in order to go the"Counter" and tehn to "Trouble"?
With this error code on the screen all my keys are locked-up.
I appreciate your help & email to "[email protected]"
Many thanks in advance.
power down copier at op-panel.straightend end of paper clip into little hole by op-panel power button.hold in till little dot appears on screen in middle to the left.press #3.that should get you to trouble reset.Or sometimes opening and closing rightside door can reset.
Posted on Jan 04, 2009
We had the c0500 Error on our printer in the office this morning. For whatever reason the 8 digit tech password is no longer 00000000 on the machine. It isn't 12345678, 1111111, or any of those other basic default passwords and not even our techs know what it is. Is there anyway to reset the tech password on this printer?
if three times you tried with wrong password at saem time you have to change ram
Posted on Oct 02, 2008
I believe it happened after a power failure. I need the codes to reset the warm up phase (I believe) for this. Is there someone that knows how to do this?
Does anyone have a tech manual for troubleshooting. Really in a bind.
I also don't have the admin code. Does anyone know how to reset this also. I own it from my previous business, but lost the codes in a move. I appreciate any input. Thanks.
look for a small hole...on right side of the disply panel...THE HOLE IS SMALL THE SIZE OF PAPER CLIP IN DIMETER..IN FACT THE ONLY WAY TO ACCESS IS BY PAPER CLIP.PRESS IT ONCE VERY GENTLY..AND WAIT FOR A SMALL DOT TO APEAR ON THE LEFT SIDE OF THE SCREEN IN THE CENTER.ONCE YOU SEE IT>>PRESS # 3 than you will be promted by a screen to reset troublr code press it to conform MACHINE WILL RECYCLE
HOPE THAT HELP S
GOOD LUCK
Posted on Dec 31, 2008
WHEN I TURN ON THE COPIER I GET THE ERROR CODE C0500, CALL FOR SERVICE.
How to reset malfunction code C0500 of a imagistic
Posted on Sep 20, 2011
HOW DO YOU CORRECT PROBLEM
To clear this code, you will need a paper clip, stick th paper clip in the small hole on the right side of the control panel, (machine must e on) When you do that the control panel wll say please wait, then the screen will show a small blue dot for a few seconds on the left side of the screen, when you see that press 3 you will see a screen the say Maintenace Mode, touch then hit "Trouble Reset" it will again say please wait, then you will see the dot again let it go do nothing it will go thru to Ready to Copy. If The code comes back you need a new fuser unit
Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f
Posted on Aug 04, 2009
no matching paper size set paper on bypass tray
Someone has told the machine to either make a copy or print from a PC to the Bypass feed tray on the copier. If you are not trying to print something by using the bypass tray then just turn the machine off, then on again to clear the request from the copier. If you are trying to print or copy from the bypass tray then simply insert the correct paper size and direction into the bypass tray slot and the machine should automatically begin printing.
Good Luck and Thank You for using Fixya.
Posted on Sep 22, 2010
error code cof32
ATDC setting error - COF32, run F8 & use actual value, do not reduce setting value. open sie cover to reset.
Posted on Feb 15, 2011
351 questions posted
Usually answered in minutes!
1,023 Questions
924 Questions
417 Questions
321 Questions
259 Questions
