20 Most Recent Konica Minolta DiALTA Di200 Copier Questions & Answers

0helpful
1answer

Konica minolta Di3510 when switched on shows only

Sir/Mam, Power off the machine. Then remove the toner bottle, be careful the hole might be on the bottom and the toner is going to go everywhere. Then close the toner cover and turn on the machine. Let the machine go through it normal routine. When it asks for toner install the toner bottle correctly. If THE KNUB on the side of the bottle is damage put a new one in. That KNUB is what the toner motor uses to turn the bottle, if it damaged you get a code. If that does not work, you might have a bad motor or the home sensor or actuator for the toner bottle is bad worse case the control board is bad. When was the last time the developer and drum where replaced
4/3/2020 9:41:07 PM • Konica Minolta... • Answered on Apr 03, 2020
0helpful
1answer

C0201 ERR CODE MINOLTA 600

Tray one lift motor is in-op or is stuck Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f
3/25/2018 4:43:20 PM • Konica Minolta... • Answered on Mar 25, 2018
0helpful
1answer

Minolta Di 351 code C045

cooling fan motor code, this motor/fan is located on the right side door behind the transfer assy. clean the fan unit, if its been to long might be burned out then replace it worse case the main board $$$$$$$$$$$$$$$$$ if you can find one;( a very legacy Minolta machine sorry Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f
3/10/2018 7:43:43 PM • Konica Minolta... • Answered on Mar 10, 2018
0helpful
2answers

Malfunction code C0040

Minolta copier show error code c0040. Please show me the picture that point of problem. The second problem. What is the way we could what kind of minolta di ...in the machine?thanks in advanced.
2/28/2018 7:37:32 PM • Konica Minolta... • Answered on Feb 28, 2018
0helpful
1answer

How to reset toner

Sir/Mam, Power off the machine. Then remove the toner bottle, be careful the hole might be on the bottom and the toner is going to go everywhere. Then close the toner cover and turn on the machine. Let the machine go through it normal routine. When it asks for toner install the toner bottle correctly. If THE KNUB on the side of the bottle is damage put a new one in. That KNUB is what the toner motor uses to turn the bottle, if it damaged you get a code. If that does not work, you might have a bad motor or the home sensor or actuator for the toner bottle is bad worse case the control board is bad. Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f
2/25/2018 11:19:06 PM • Konica Minolta... • Answered on Feb 25, 2018
0helpful
1answer

I have a Minolta

was the power on when you depressed the small switch? you mite have damage the lamp in the fuser or the control board. very old machine find the parts and replace them Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f
5/7/2017 3:36:07 AM • Konica Minolta... • Answered on May 07, 2017
0helpful
1answer

Error code c0500

C500 is a fuser code, the hot part of the machine, the fuser fuses the toner to the paper, so that the toner does not smear off. But to solve this must have the model number. As each series of machine has a different way to reset machine Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f
12/11/2016 1:57:23 AM • Konica Minolta... • Answered on Dec 11, 2016
0helpful
1answer

Code bizhub c350

Mam, Open the front door lay down on the floor and look up at the section that is slanted (close to hinge side of the front door) Fine the small hole with the machine on, fine a small non metalic stick and in-cert into the small hole touching the small switch which will re-set the machine for C-0500 codes. Do this once if the code comes back replace the fuser, DO NOT RE-SET again messing with FUSER can catch on fire will ruin a perfectly good day. Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f
7/9/2016 10:01:33 PM • Konica Minolta... • Answered on Jul 09, 2016
0helpful
1answer

Konika minolta bizhub 163 error code C0F33

replace the developer and drum or the image unit as a whole Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f
7/6/2016 12:14:52 AM • Konica Minolta... • Answered on Jul 06, 2016
0helpful
1answer

Minolta dialta di850 error code 28-04

7/4/2016 5:15:41 AM • Konica Minolta... • Answered on Jul 04, 2016
0helpful
1answer

Need to add email address

Self Help Product Support Konica Minolta Business Solutions Inc try this site Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f
7/3/2016 8:00:37 PM • Konica Minolta... • Answered on Jul 03, 2016
0helpful
1answer

Cari toner di 351 di surabaya

English please Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f
7/3/2016 6:04:23 PM • Konica Minolta... • Answered on Jul 03, 2016
0helpful
1answer

Download driver mac

Self Help Product Support Konica Minolta Business Solutions Inc trythtis site Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f
7/2/2016 8:46:35 PM • Konica Minolta... • Answered on Jul 02, 2016
0helpful
1answer
0helpful
1answer

Replacing a heater unit

Service manuals electronic components datasheets and equipment schematics... tyr this site for manual Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f
6/27/2016 3:44:36 AM • Konica Minolta... • Answered on Jun 27, 2016
0helpful
1answer

Aurora Error code C0500

Sir/Mam First open the right side cover where the image unit is located. Check the two latches that latch the door ensure they are not broken, especially the rear one. Then get a paper clip and stick the clip in the small hole on the right side of the control panel it will touch a switch. The control panel will go thru some screens when you see the screen with the copiers on it on the left side of the screen in the middle you will see a small "." When the dot appears touch 3 button. Then the machine will continue to the code screen. Press the Utility button you should see a new button "Maintenance Mode" touch it then touch trouble reset. The machine will again go thru screens will see the"." again do nothing. Should go ready to Copy. If the code comes back do not reset, you are messing with the Fuser the Hot part. Continuing to reset without a technician looking at and or replacing it, the fuser can catch on fire and that would ruin a perfectly good day. Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f
6/27/2016 3:23:07 AM • Konica Minolta... • Answered on Jun 27, 2016
0helpful
1answer

Malfunction detection

large capacity draw check it Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f
6/26/2016 8:04:57 PM • Konica Minolta... • Answered on Jun 26, 2016
0helpful
1answer

C-of24

no such code for this machine Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f
6/25/2016 5:55:17 PM • Konica Minolta... • Answered on Jun 25, 2016
0helpful
1answer

HOW MANY TONERS USE THE DIALTA DI470

one Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f
6/25/2016 5:53:14 PM • Konica Minolta... • Answered on Jun 25, 2016
0helpful
1answer

Code M4 erro

Service mode, first 1.Press the Utility key. 2. Press the Meter Count key. 3. Press the following keys in this order: Stop  0  0  Stop  0  1 for security "Stop 9" In Security, Select Copy Kit 1. Touch "Set." 2. Press the Clear key to clear the current setting. If the setting is accidentally cleared, press the Interrupt key to undo the clearing operation. 3. Enter the desired value from the 10-Key Pad. 4. Touch "Current." 5. Press the Clear key to clear the current value. If the current value is accidentally cleared, press the Interrupt key to undo the clearing operation. Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f
6/25/2016 5:01:38 PM • Konica Minolta... • Answered on Jun 25, 2016
Not finding what you are looking for?
Konica Minolta DiALTA Di200 Copier Logo

351 questions posted

Ask a Question

Usually answered in minutes!

Top Konica Minolta Office Equipment & Supplies Experts

George Mclaughlin

Level 2 Expert

372 Answers

Marvin
Marvin

Level 3 Expert

85240 Answers

Cindy Wells

Level 3 Expert

6491 Answers

Are you a Konica Minolta Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Konica Minolta Office Equipment & Supplies

  • Konica Minolta Office Equipment & Supplies

Most Popular Question

c004c

  • Office Equipment & Supplies
Loading...