Top 20 GE WBXR2090B Top Load Washer Questions & Answers


If you are refering to the sloshing sound when tub is moved back and forth it is supposed to be there. That is the balance ring. It is a liquid filled ring at the top of the tub that acts as a counter weight to keep tub balanced.

GE WBXR2090B Top... • 316 views • 1 helpful votes


Check exit hose for leaks and replace hose and/or hose clamps.

GE WBXR2090B Top... • 44 views • 0 helpful votes


Two clips between front panel and top, push clips with small screwdriver pull front panel out.

GE WBXR2090B Top... • 136 views • 1 helpful votes


IT SHOULD BE A FEW SCREWS ON TOP THAT NEED TO BE UNSCREWED THAT SHOULD GET IT DONE

GE WBXR2090B Top... • 64 views • 0 helpful votes


There is an internal overflow hose to prevent water from getting onto the motor and other electrical components. It sounds like the overflow system did its job.

The water you hear is likely one of two things: a small amount of water that is still in the tub, under the basket, which is nothing to worry about. Or, you are hearing the fluid (that is supposed to be there) in the balancer.

GE WBXR2090B Top... • 90 views • 0 helpful votes


There should be 2 screws holding it on at the rear. Looking from the rear these will be at each top corner. Once these are removed push the lid from the front of the machine towards the rear and it will pop off.

GE WBXR2090B Top... • 2,009 views • 3 helpful votes


Scot, it almost sounds like you have a motor issue here. Does the machine go through the spin cycle o.k.? If you are handy with a meter, remove the front panel, push in on the clips on each side of the top with a puddy knife and the panel should come off. On the motor harness there should be a white and white/red wire. If you have a steady, not fluctuating, 120V during this bucking, it's more than likley your motor. If the voltage is fluctuating, it would be a timer issue. You also want to make sure you have nothing caught under the agitator, this will pop right up with a good tug. Catriver, post back.

GE WBXR2090B Top... • 88 views • 0 helpful votes


either the control board or the pump is bad

GE Washing... • 17 views • 0 helpful votes


remove fabric option then long extension and screw at bottom could be reverse threads

GE Washing... • 22 views • 0 helpful votes


possible springs holding tub loose or off or tub spinning off balance bad bearings or loose

GE Washing... • 17 views • 0 helpful votes


Set the load to large, set the water temp as hot as it allows, pour in two cups of bleach and run it with no clothes.

GE Washing... • 15 views • 0 helpful votes


There could be a defective cycle timer or a defect in some controlled assembly.

GE Washing... • 25 views • 0 helpful votes


possible bad belt if ok bad motor or check under agitator for bad cogs to tub

GE Washing... • 21 views • 0 helpful votes


perhaps the brain has failed . only a good repair shop can test .

GE Washing... • 21 views • 0 helpful votes


try you tube for a video we do not have them here

GE Washing... • 21 views • 0 helpful votes

Not finding what you are looking for?
GE WBXR2090B Top Load Washer Logo

Popular Tags

22 questions posted

Ask a Question

Usually answered in minutes!

Top GE Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8221 Answers

Michael Thomas
Michael Thomas

Level 3 Expert

3056 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1482 Answers

Are you a GE Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

GE Washing Machines

  • GE Washing Machines

Most Popular Question

washer tub water but will not drain

  • Washing Machines
Loading...