20 Most Recent GE WBSR3140DW Top Load Washer Questions & Answers

0helpful
2answers

Washer will not fully drain

check drain, screen, and hose for clog and buildup

5/13/2022 8:51:10 AM • GE WBSR3140DW... • Answered on May 13, 2022
0helpful
2answers

Washer will not spin at high speed

check for any blockages around pump and air trap area.
8/23/2021 9:07:13 PM • GE WBSR3140DW... • Answered on Aug 23, 2021
0helpful
1answer

GE Washer Model WJRR4170E4WW squeaks while agitating

There are four suspension rods that the tub hangs on. When the washer is agitating the tub will rock back and forth and the rods will move back and froth as well. To fix this noise, lift up in each rod and put some lubricant in the cup that the rods fit into at the top of the washer.

Note that it is best if you use a lithium-based lubricant rather than silicone based lubricant.

For more on do-it-yourself appliance repair help visit http://www.appliance-repair-it.com/index.html
10/14/2020 11:27:49 AM • GE WBSR3140DW... • Answered on Oct 14, 2020
0helpful
2answers

GE Profile washer won't spin cloths after wash or rinse cycle

Make sure you magnet is properly in place its very touchy
10/14/2020 7:34:51 AM • GE WBSR3140DW... • Answered on Oct 14, 2020
0helpful
1answer

Spins when empty. Why not when full?

When the machine is full, the built in sensor triggers a switch to let the machine know there are clothes inside. Check the sensors and/or switch, as they may be faulty.
9/23/2019 9:31:25 AM • GE WBSR3140DW... • Answered on Sep 23, 2019
0helpful
4answers

How do you reset the washer?

I have a GE WBSR3000GWS Model and it stopped spinning at one point as well. My service guy came out and did the procedure below and reset it with in minutes.

How to Reset your GE Washer :
1. Turn the dial like your going to wash a load but do not pull the knob.

2. Unplug the washer from the wall and wait for 30 seconds.

3. Plug the washer back into the wall.

4. Lift the lid 5 times to at least 6 inches high. Open/Close within 15 secs.

5. Pause… You should here a click. If you do not, then repeat 1 – 5 again.

6. Insert a towel or garment into the washer and then pull knob to start the wash cycle.

7. Check the wash cycle to make sure the washer is agiating and spinning during its cycle.

GE Answer Center : 1-800-626-2000 opt 3 - for more information
Lale
6/19/2019 8:47:42 PM • GE WBSR3140DW... • Answered on Jun 19, 2019
0helpful
2answers

GE top load washer w/no lint trap leaves excessive lint

Most US-sold washers made after the mid 1980s don't have lint filters. The manufacturers weasel-word around it by saying that the lint "goes down the drain", leading people to optimistically assume that there is a self-cleaning filter in there somewhere. There usually isn't and whatever lint doesn't go down the drain is filtered by your cloths (but whatever does might clog your septic system). As a result of this scam, it's much harder to hang-dry or iron-dry clothes that haven't been hand washed. And, if you think spending $2000 on a pair of matched "front-load" style machines will solve this, you might be wrong; many of those washers still have no lint filter.
3/25/2019 11:49:52 AM • GE WBSR3140DW... • Answered on Mar 25, 2019
0helpful
3answers

Washing machine spins slowly and smells of burning rubber

The belt could be worn and will be slipping on the pullys, as it spins up the rubber , rubs against the pullys and that is what creats the burning rubber smell, the belt needs replacing.

regards jonno
1/30/2019 10:12:51 PM • GE WBSR3140DW... • Answered on Jan 30, 2019
0helpful
1answer

Ge washer making clicking sound

Hi, I don't know the model, but it's possibly moving the water fill nozzle over the Fabric Softener compartment in the soap drawer. Clicking is normal for that.
1/31/2018 5:30:27 AM • GE WBSR3140DW... • Answered on Jan 31, 2018
0helpful
1answer

Washer won't hold water, just drains to the floor.

Sounds like there's a hole or loose ejection water hose.
Move the washer so it will run and you can look in the back to see where the water is coming from....fix the leaky problem once you find it. Could be a bad hose clamp as well
12/12/2017 11:15:12 AM • GE WBSR3140DW... • Answered on Dec 12, 2017
0helpful
1answer

Washing Machine won't do anything and is full of water

Check to see if the tub is free to move in at least one direction or the drain pump for blockage from a small item of clothing. It's best to wash small items in a laundry net bag when mixing with large items to prevent one from getting pushed over the top of the inner tub and either blocking the pump or jamming the tub. Hope this helps you.
11/22/2017 10:13:57 AM • GE WBSR3140DW... • Answered on Nov 22, 2017
0helpful
1answer

Crystal-like substance

It sounds like your water system might need some filter housings installed?-- are there any filter housings in any of your water systems?-- If so, what are they accumulating-- what do you find, when you change filters. Write back what you are finding.. If you have no filters, then let's install either ONE on your common cold water supply to the house-- or start with two at your washing machine. Which would be easier?- Write back-- Mack Baxter
11/4/2017 12:20:55 PM • GE WBSR3140DW... • Answered on Nov 04, 2017
0helpful
1answer

I HAVE A GE TOPLOAD WASHER MODEL#WSKS2060T1WB AND

Take tub out, liner is cracked above motor do to off center load. Install new liner but cut fin off above motor before installing to stop this problem.
10/5/2017 2:13:16 PM • GE WBSR3140DW... • Answered on Oct 05, 2017
0helpful
1answer

Ge wbsr washer overflows...

Could it be ...this happens only when it is overloaded or the load is out of balance. Please clarify. If this is not the case .. the water level hose running from the outside tank to the water level switch is likely not making a good seal (otherwise the water level switch itself is bad). Sometimes with age the hose forms a crack in it near or at the end where it connects. This could happen at either end of the hose. Also if you have removed the control panel recently (for any reason) you may have (not knowingly) pulled the water level hose loose from the water level switch. Just slide the hose back onto the tube of the switch before putting the control panel back in place and all will be fine after the first filling of the tub (it may take one filling cycle to build the needed vacuum back up in the hose). Unless of course in the process you have broken the tube off the switch where the hose goes on. In this case replace the switch.
6/5/2017 3:40:25 PM • GE WBSR3140DW... • Answered on Jun 05, 2017
0helpful
1answer

Washer fills slow only in the rinse cycle

Need a model # to get exact part you will need at rinse most washer go straight cold so I would say water inlet valve if humming sound is present
4/28/2017 11:50:07 AM • GE WBSR3140DW... • Answered on Apr 28, 2017
Not finding what you are looking for?
GE WBSR3140DW Top Load Washer Logo

1,337 questions posted

Ask a Question

Usually answered in minutes!

Top GE Washing Machines Experts

Tim Whalen

Level 3 Expert

3076 Answers

Marvin
Marvin

Level 3 Expert

85240 Answers

Mike

Level 3 Expert

4383 Answers

Are you a GE Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

GE Washing Machines

  • GE Washing Machines

Most Popular Question

bypass magnetic safety switch ge washer

  • Washing Machines
Loading...