20 Most Recent GE DBXR463EBWW Electric Dryer - Page 8 Questions & Answers

On that model, look for screws below the kick strip (parts 238). After removing that, look for screws to remove the front panel where the lint filter is (parts 502). Don't stretch the wires to the door switch. The link also has a full parts schematic showing the screw locationshttps://www.geapplianceparts.com/store/parts/assembly/GFD45ESSM1WW....

Hey Linda, thank you for the question. If you are talking about the timer of your GE dryer, if it is stop working completely you may need to replace it with the right part number. For me to locate the compatible timer of your dryer I need model number of your dryer. You can not repair the timer of your dryer but you can clean the carbon or any dust particles come in between the knob and timer switch causing the timer to behave abnormally. You can get access by removing the top cover using a putty knife. Clean or clear the terminals where the harness connect to the switch. I hope this will clear the issue. Thanks again for the great question.

no info generic answer ---what metal plate --a cover a bracket --vent etc --what unit model no --their are multi plates / brackets --order new one and replace

Try pressing on the door switch and running it with the door open, if it works you need to replace the door switch

Question edited for clarity. Question moved from Cars and Trucks category. Did you look inside the back console where the control knob is for the wiring diagram? They are normally inside there in a plastic bag. It is only for the door switch, so it is just a two wire, open / closed circuit. Join blue to blue, and pink to yellow. There are generic GE Door Switch replacement videos here. https://www.google.com/search?q=gtd72ebpn0dg+replace+door+switch https://www.google.com/search?q=GTD72EBPN0DG+door+wiring+diagram ..

Service manual and the wiring diagram is here, but Gas appliances should only be worked on by a certified gas technician. Working with upgraded or changed copy parts is a nightmare. Direction should come from North Pacific Timer, as they will know what the contacts do, and in conjunction with GE, they know what the wires do. The wires should fit into the same locations on the timer. Did you take a picture before you disconnected it? https://www.manualslib.com/manual/1546860/Ge-Gud27essmww.html?page=77#manual ..

GE WE3M26 Dryer Drum Front Support Bearing (AP3790641) - AppliancePartsPros.com

The noise was probably a bad support roller - likely cause for it not starting after reassembly is the door switch was probably not reconnected

Question moved form GE Land Phones. Is it clothes like a sock or underwear? Take a wire coat hanger and un-twizzle it with pliers. Pull the door gasket back a bit and slip the hooked end between the inner and outer drum. Pull the item to the front. You can turn the drum to help the item catch onto the hook.

CL usually indicates that the Child Lock (control panel lock) has been enabled. This is useful when you clean the control panel. It also keeps someone from accidentally starting the dryer with a pet or another child in the dryer. This is toggled on and off by pressing and holding two buttons. There is usually a line between the buttons with a padlock symbol in the middle or above that line. The phrase Control Lock or To Lock Control will be below the line. The symbol and text will be in a small font. On some GE dryers, press and hold the Extended Tumble and - buttons for 3+ seconds. The CL indicator should flash while you unlock the control panel and then go off when you've held the buttons for sufficiently long. Note: if you hold the buttons for too long, you will re-enable the lock. For the GE Profile DPGT650EHWW, press and hold Dry Level and Temp for the 3+ seconds. See page 6 of the Use and Care manual here: https://www.geappliances.com/appliance/GE-Profile-7-1-Cu-Ft-King-size-Capacity-High-Efficiency-Electric-Dryer-DPGT650EHWW . I hope this helps. If you need help finding the control panel lock key, please add a comment with the model of your dryer. Cindy Wells

Check out the videos Esther. That is normally caused by an overheating issue, and that is always cause by lack of airflow. Check the pipes at the back and the outside vent for birds nests and lint build up. https://www.google.com/search?q=ge+dryer+gfd45essmww+disassembly .Why does my GE dryer keep shutting off? Most likely, a thermal overload switch is shutting down the dryer because it's getting too hot or the motor is overworking. A gas dryer can get too hot if the vent is clogged and, eventually, this can damage the motor. Or the overload switch itself can go bad. The timer can be broken, too.Feb 24, 2020

Why does my GE dryer keep stopping? - AskingLot.com

Videos for it https://www.google.com/search?q=ge+dryer+gfd45essmww+switches+off ...

CODE: 009 PROBLEM: Drive motor problem FIX: If the drive motor won't run, unplug the dryer and reconnect any loose wires on the drive motor. Replace the wire harness if damaged.

Number 1 tip. TURN OFF THE MAINS POWER. You are dealing with 220 volts at 30 amps. That part is a simple mechanical timer. Get out your multimeter and check the switch for continuity and correct operation. Then go and check the fuse or breaker. A dead short like that should have tripped it out or blew the fuse. If it was an electronic machine, it would have required a new control board. https://www.google.com/search?q=M460-G+572D520P018&tbm=isch&ved=2ahUKEwinst_ssYj2AhVMhHIEHRv9A5AQ2-cCegQIABAA&oq=M460-G+572D520P018&gs_lcp=CgNpbWcQAzIHCCMQ7wMQJ1AAWABg9wxoAHAAeACAAViIAViSAQExmAEAqgELZ3dzLXdpei1pbWfAAQE&sclient=img&ei=Fh0PYqfPG8yIytMPm_qPgAk&rlz=1C1QJDB_enCA643CA644 ..

check under unit or back

https://my-secure.justanswer.com/question/guest/64e3442ca7bd42218c81bf0cf7b21ebb#re.v/7350,7484,7776/ https://my-secure.justanswer.com/question/guest/31352a92892f4a83a1caea4c5631156e#re.v/7350,7484,7776/

How to replace https://www.google.com/search?q=GE+Profile+Model+DPSR610GG6wt+replace+thermal+fuse They call it a 'Safety Thermostat'. Parts schematic here https://www.searspartsdirect.com/model/kkdqo4n280-000432/ge-dpsr610gg6wt-dryer-parts ..

first off get a new lint filter part number WE18X53 and it's around 20 to 30 dollars depending on where you buy it,now when you say you cleaned the dryer do you mean you cleaned just where the clothes go into or did you unplug it and take it apart and clean it out?if you look at the inside back wall you'll see holes,on g.e. dryers lint builds up behind the drum and the heat shield,you can try vacumming the lint out of the holes but the best way is to pull the drum,clean the back of the drum out where i was just telling you about,vacing out the cabinet where the motor is and then blow off the motor and cabinet with the shop vac the other side of it blows air and clean out the duct where the lint filter is and clean out the door,then blow out the vent line,if the line is long you can remove it from the dryer and blow it out with a leaf blower,it sounds like the dryer never has had a clean out,i know you most likely will have to call some one in to do this but for now with a shop vac set it up to blow,remove the lint filter and blow all the lint out of the duct,blow it for a few seconds the vac up the lint and do it again until it's clean,then vac the back of the drum,if you put a light in the drum you can see the lint through the holes,you can try blowing through the holes to lossen the lint and then vac it out and see if that helps but the dryer has to be taken apart and cleaned so you don't have a fire,this should be done at least once a year if it's gas and once every 1 1/2 to 2 years if electric,this way your clothes will dry on time and mostly so you don't have a fire. also when it's pulled apart you can check all the parts to make sure nothing has to be changed out like the rear bearing and rollers and pulley,also check the heater to make sure it's not sagging after a while on electric dryers the heater coils can sag down and short out,when you have it apart you can tighten them up and bend them up into shape again,hope this helps and good luck with your machine.

On most dryers the top piece of the main cabinet pops off. It is held on with clips and it can be a challenge to remove without scratching the paint. Once this is done you can see the bolts that hold the front section to the frame or the rest of the cabinet.

1. User manual GE® GFD14ESSNWW Dryer ' manualsFile https://manualsfile.com/product/5i1x17x3f.html GE - General Electric GFD14ESSNWW ' File type: PDF ' Filename: GE® GFD14ESSNWW 24" 4.3 Cu.Ft. Front Load Vented Electric Dryer with Stainless Steel Basket.pdf ' Size: 3.68 MB ' Language: English, French, Spanish ' Other documents: 1 files. Download User Manual.

I exoect the drum bearing has fallen apart. Look for a new machine, it is probably cheaper.