20 Most Recent GE Profile Harmony DPGT750GC Gas Dryer - Page 7 Questions & Answers

Typically, conversion from natural to propane and visa-versa is just a simple connection behind the appliance. Look in the box of the conversion kit (or on the back of the packaging,) and you should see the conversion instructions. Since you are dealing with gas, you need to make sure the shut-off valve is... shut off so no gas can leak while do the exchange. Also, make sure there are not open flames anywhere near the work area. Take your time and follow the directions...

open top and check connections, unplug power and reconnect after done. if this does not solve it then I would replace display board. this dryer is made by LG, controls should be good.

if your blower motor isn't getting up to speed it won't heat.check troubleshoot mode by holding my cycles and help at the same time for three seconds.may need a new blower motor

your blower motor is probably not working. enter the troubleshooting mode by pressing and holding my cycles and help at the same time for 3 seconds. this will tell you the problem. if blower is not getting up to speed you'll have to replace it.

The way to remove/separate the spinner from the blower motor is that, if you'll notice, there's a flat notch on the back of the blower motor shaft. You have to put a crescent wrench or some sort of adjustable wrench on the backend of that shaft to keep it from spinning. Now, the other thing that you may not be aware of is that in order to remove the nut for the spinner/blower cage, you have to turn the wrong way. Yes, you heard me right, the opposite direction. I know we were taught, righty tighty, lefty loosey. Not in this case, the nut is removed in the opposite direction.

WHERE?

Possible Solution...
When you get message first try turning off. Open door spin drum one or two times. Close door. Power back on/start.
Works for our problem. Post if this helps.

Check the connectors and lugs on the powercord ,wire and breaker box

yes youllneed to know the exact model of your dryer, then you can call the manufacture for a conversion kit. not going to be Available at hardware or plumbing supply,

Replace the rear drum bearing and the tension roller wheel.

Check for 220 Volt at the heater entrance to the heater box (accessible from picking up the top on most models). If you have 220v there the heater element is out. If you don't have 220v on the terminals of the heater the problem is in the controls. The fuse link, the timer contacts, the centrifugal switch on the motor, and the heater safety thermostat and operating (s), are all suspect and have to be eliminated 1 by 1. Hope this helps. With any luck all you need is a new element. Clean the duct out while replacing the heater if so because the main thing that causes heater element burn out is low air flow a kinked Dryer vent hose, lint, and plugged up fan on the motor are the 3 main causes of low air flow. If yours has little holes in the inside cabinet these can get clogged with lint also and cause a problem. Hope this helps and please rate me accordingly Thank you and good luck.

Check that the vent outside (especially in northern climates this time of the year). Then check the hose that goes from the drier to the outside vent. Finally, check the drier itself, that there is no obstructions getting to the hose. Check the lint trap. Is it full or is it installed properly? If all this checks out, then try replacing the heating element. These are usually inexpensive, and fairly easy to replace. The manual for the drier should have diagrams on how to access it.

Check the door switch If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61

Hello chucky40,
There is a good chance that your gas valve has been damaged by the water. Can you tell if after you try starting it if the igniter comes on and/or you have gas flow to the burner? Those are the prime suspects ( albeit not the only ones) but you will need to verify these basic functions before others can be examined..
Keep me posted and I'll try to help you get thru this..
Regards,
Rick

i am sending you all the possibilities for your problem, check either of these causes ----and than let me know if it is solved----

Power from the house
Check to see whether there's power getting to the dryer. Is it plugged in? Check for blown fuses or tripped circuit breakers--your dryer uses two fuses or circuit breakers. The dryer could tumble but not heat if only one of the two fuses is blown. If you have circuit breakers, one of the two circuit breakers can trip, even if the two for the dryer are connected.


Heating element
Often a dryer heating element burns out, but doesn't trip the circuit breaker or blow a fuse. The heating element is simply a long coil of special wire. You can check it for continuity with an ohm meter. No continuity means the element is bad and you need to replace it--electric heating elements aren't repairable.


Thermal fuse
On many dryers, there's a thermal fuse mounted to the exhaust duct inside the back cover panel. The fuse--which is about an inch long--is usually embedded in black resin and mounted in a white plastic housing. If the fuse has blown, you need to replace it. (You can't re-set it.)


Wiring
A common problem is for the main wiring connection from the house, at the dryer, to burn and break its connection. Because the dryer can still tumble with partial power, the connection may be only partially defective. You may need to replace both the power cord to the dryer and the terminal block inside the dryer that the wire is attached to.

I would purchase an extended warranty because the problem will not just go away. It will eventually get worse