20 Most Recent GE Profile Harmony DPGT750EC Electric Dryer Questions & Answers

0helpful
2answers

How do I know if it's the heating element or the blower motor

you need a service tech there if you arent the mechanical type it could be the heating elements or a thermostat as welll
11/18/2019 5:24:08 PM • GE Profile... • Answered on Nov 18, 2019
0helpful
1answer

GE Profile Harmony electric dryer blower motor not working

this dryer has two motors in it,all of the errors other than the touchpad were for heat problems and most likely caused by a bad blower motor that did fail alot.
11/2/2018 2:03:18 AM • GE Profile... • Answered on Nov 02, 2018
0helpful
1answer

Need service manual for ge profile dryer

Hello, this is Ava with Think Crucial. You may find the User's Manual for your GE model by clicking the link below. GE PTDN600EMWT Manuals You can purchase a wide variety of high quality appliances replacement parts direct from Think Crucial with free shipping and an exclusive 10% coupon for Fixya.com readers, use code: FIXYA10 https://www.thinkcrucial.com/collections/appliances I hope this was helpful. Ava B. Think Crucial Customer Care http://www.thinkcrucial.com/
4/28/2018 12:07:16 AM • GE Profile... • Answered on Apr 28, 2018
0helpful
2answers

Ge dryer not heating

i am sending you all the possibilities for your problem, check either of these causes ----and than let me know if it is solved----

Power from the house
Check to see whether there's power getting to the dryer. Is it plugged in? Check for blown fuses or tripped circuit breakers--your dryer uses two fuses or circuit breakers. The dryer could tumble but not heat if only one of the two fuses is blown. If you have circuit breakers, one of the two circuit breakers can trip, even if the two for the dryer are connected.


Heating element
Often a dryer heating element burns out, but doesn't trip the circuit breaker or blow a fuse. The heating element is simply a long coil of special wire. You can check it for continuity with an ohm meter. No continuity means the element is bad and you need to replace it--electric heating elements aren't repairable.


Thermal fuse
On many dryers, there's a thermal fuse mounted to the exhaust duct inside the back cover panel. The fuse--which is about an inch long--is usually embedded in black resin and mounted in a white plastic housing. If the fuse has blown, you need to replace it. (You can't re-set it.)


Wiring
A common problem is for the main wiring connection from the house, at the dryer, to burn and break its connection. Because the dryer can still tumble with partial power, the connection may be only partially defective. You may need to replace both the power cord to the dryer and the terminal block inside the dryer that the wire is attached to.

3/27/2018 4:09:43 PM • GE Profile... • Answered on Mar 27, 2018
0helpful
1answer

Blower Motor not working

This is not a board issue.It sounds like the blower is either broken or fell off the motor.Remember your dryer has 1 motor.On one side is where the belt is attached,and on the other side your blower is attached.
2/24/2018 3:36:30 PM • GE Profile... • Answered on Feb 24, 2018
0helpful
1answer

GE profile harmony dryer has power, drum turns,

check out the ignition spark ignitor
that makes the burner to heat up
2/24/2018 3:32:15 PM • GE Profile... • Answered on Feb 24, 2018
0helpful
2answers

I have a GE Profile

only if you can get a ge training manual,check with ge
2/22/2018 10:13:16 PM • GE Profile... • Answered on Feb 22, 2018
0helpful
1answer

GE Profile Harmony Dryer DPGT750EC2WW need manual

http://members.msaworld.com/wp-content/uploads/sites/3/2016/09/31-9104.pdf
2/21/2018 10:45:34 PM • GE Profile... • Answered on Feb 21, 2018
0helpful
1answer

My GE dryer only heats

Hi,

If you are having problems with your gas dryer not heating the most common problem is that the ignitor goes bad. Even though it glows sometimes it is still not working properly.



if you dryer is gas check out this gas no heat tip....



If you have an electric dryer, you can have many different things that can go wrong causing the dryer not to heat.



check out this electric no heat tip...


heatman101

2/20/2018 1:23:25 AM • GE Profile... • Answered on Feb 20, 2018
0helpful
2answers

Does the GE harmony dryer have a blower motor that

No normally the blower is not driven by a belt, it is a motor with a blower wheel attached on the end of it...if the blower motor is not working then you will have to replace the blower motor
2/20/2018 1:06:52 AM • GE Profile... • Answered on Feb 20, 2018
0helpful
2answers

The dryer will not start. I checked the circuit breaker and it is okay. Unplugged the dryer for a few minutes and tried to restart but would not work. It stopped while in a drying cycle

I could be your thermal fuse, that would be the first place to start after checking wiring connectivity, good luck
2/18/2018 6:44:28 PM • GE Profile... • Answered on Feb 18, 2018
0helpful
1answer

Replaced motor, and problem still occurs. Washer will not get past checking drive system during self test.

what was the error code and what's the brand name and model number of the washer?
1/6/2018 11:19:27 PM • GE Profile... • Answered on Jan 06, 2018
0helpful
1answer

GE Profile DPGT750EC1PL Blower Thermostat Reading

When you start the dryer does the drum rotates
10/7/2017 3:30:42 AM • GE Profile... • Answered on Oct 07, 2017
0helpful
1answer

My GE Profile high efficiency dryer has wrked grt

Could be inveter board or heat sensor. You would need to find info on how to replace on the web. Try Here is the procedure for in-cycle sensor output. Press "Home" Press "Home" and "Help" simultaneously until you hear a beep. Press "Special Cycles" on touch screen. Choose Towels Start the cycle...magically you will see a bunch of numbers on the right side! Some numbers will be 0 for 5-20 seconds until the sensors pick up inputs. I'll try to list the sensor outputs to the best of my ability(they're not labeled) blower speed (will vary during course of cycle) moisture %? temp of inside of drum? drum motor speed? heater 1? heater 2? voltage /// seconds until complete OK Voltage with number under it is Hertz (60 Hertz US, 50 Hertz Europe) If any of these numbers remains 0, there is a problem!
9/11/2017 2:36:20 AM • GE Profile... • Answered on Sep 11, 2017
0helpful
1answer

GE profile electric dryer, sounds like something is stuck in drum

Heating problem is most likely caused by one strand of your heating element is burned out. Heating element will have to be replaced if that's the case. Noise you are hearing is most likely coming from worn front and / or back bearing. Dryer has to be completely disassembled for either repair.
8/28/2017 5:26:25 AM • GE Profile... • Answered on Aug 28, 2017
0helpful
1answer

GE Harmony Dryer makes Loud Vibrating noise

If you can open the walls of the dryer up check all screws and bolts that hold things together. Some times they will vibrate loose causing parts to make a vibrating sound against the frame itself.. Eventually the loose screws will just keep getting looser. Even the screws on the walls of the unit should be tightened That could cause a lot of noise.
4/10/2017 12:43:07 PM • GE Profile... • Answered on Apr 10, 2017
0answers
Not finding what you are looking for?
GE Profile Harmony DPGT750EC Electric Dryer Logo

634 questions posted

Ask a Question

Usually answered in minutes!

Top GE Dryers Experts

David Shaub

Level 3 Expert

2994 Answers

wadingriver
wadingriver

Level 3 Expert

2248 Answers

Barrissimo

Level 1 Expert

32 Answers

Are you a GE Dryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

GE Dryers

  • GE Dryers

Most Popular Question

control panel will not work no lights

  • Dryers
Loading...