20 Most Recent Bionaire BW2300 Window Mount Fan - Page 5 Questions & Answers

0helpful
1answer

How do I remove the 10 long florescent boxes in my kitchen ceiling? I can not afford an electrician.

they twist and turn to take them out
8/20/2021 8:35:20 AM • Dryers • Answered on Aug 20, 2021
0helpful
1answer
0helpful
1answer

Dryer won’t spin is the belt broken

Electric dryer no start does nothing Check dryer Terminal block prongs both outside prongs should give combined 220, and 110 each if u check 1 outside & 1 center (ground) prong. Also check house electrical outlet for full voltage. CHECK THERMAL SHUT OFF THERMOSTAT USUALLY LOCATED ON THE BLOWER. for OHMS or resistance with a meter. Should show a closed circuit. Ohms WHEN THIS FUSE BLOWS IT WILL SHUT DOWN EVERYTHING. NEXT Test the PUSH start switch with meter for OHMS. Should show OHMS when pushed in or on start, and no ohms or infinity when in off position. If you hear a humming/clicking sound from motor area you more than likely have a bad motor. Try this test out to see if u have weak windings or relay/capacitor on motor. Open the dryer door and turn by hand the drum while machine is on ON position. And you or someone else presses the door engagement switch in. If it starts up then u have bad windings Another thing to check is the belt safety switch. With a multi meter. Especially if u just replaced the belt. The belt safety switch is attached to the Tensioner and motor. IT LOOKS LIKE A DOOR SWITCH SOMEWHAT a little black pc of plastic with 2 prongs going into it. Sits at bottom of motor. Under the Tensioner. Attach meter clips to the 2 prongs on switch, Then when the little white push button is pressed in it should show continuity and none when released. Lastly check ur DOOR SWITCH for continuity with a meter when the button is pushed in the (on/Door closed position,) it may have gone bad. https://www.youtube.com/watch?v=MhVUEhngZMg https://www.youtube.com/watch?v=9xD7lCXJ0ZM https://www.youtube.com/watch?v=sTRP6kHqAFs GOD IS GOOD !!!! WHICH IS WHY MY ADVICE IS FREE bypass thermal fuse-undefined-undefined-0.jpg cord dryer_terminal_block-undefined-undefined-2.jpg doorswitch test -undefined-undefined-5_0.jpg push start switch frigidaire dryer start switch-undefined-undefined-7_0.jpg fuses dryercyclingfuse-undefined-undefined-13.jpg bypass-lid-switch-unplug - 5-undefined-undefined-18.jpg
8/17/2021 7:04:27 AM • Dryers • Answered on Aug 17, 2021
0helpful
1answer

Fischer & Paykel DE7027G1. Runs continuously with error code 151. How can I remove and replace relay 2 (orange on the control board)?

Dryer will not shut off: The timer: Located in the control console of the dryer the timer consists of a small motor connected to a series of gears that rotate cams, which turn electric contacts off and on inside the timer. The timer contacts control the dryer motor as well as the heat circuit and the timer motor itself. A defective timer motor or a defect in the timer's electrical contacts can cause the timer motor to fail and the timer will need to be replaced. The contacts can be checked for continuity with a multi-meter. This test should only be made when the dryer is unplugged. Another test u can do is observe by eyesight and see does the timer advance or is it stuck on one cycle? 1. On gas and electric dryers that have an "Auto Dry" cycle, the cycling thermostat is often used to advance the timer as well regulate the drum temperature. Essentially, thermostat will alternately turn on the heat source or the timer motor when the temperature has been satisfied. To check this thermostat, you will have to check for power to the timer motor with a multi-meter, during a cycle. This is a live voltage test and caution should be used. 2. Some dryers will use a cool down thermostat to tumble the clothes without heat, at the end of the dry cycle. Power is routed through this thermostat to the drive motor to keep it running until the drum temperature has dropped to a specific temperature. If this thermostat fails it can cause the drum to turn indefinitely or until the door is opened. You can check the thermostat for continuity with a multi-meter. This test should only be made with the power removed from the dryer. Lastly check the moister sensor for OHMS according to ur schematic as it must show a certain amount of ohms as per ur unit. When unit has been on short while timer motor wires-undefined-undefined-0.jpg knob-on-dryer-broken-undefined-undefined-2.jpg teststartswitchr1-undefined-undefined-4_0.jpg
8/17/2021 7:00:57 AM • Dryers • Answered on Aug 17, 2021
0helpful
1answer

Zde57140w seems to be working ok but not drying?

ELECTRIC Dryer no heat or little heat, or shuts down to fast: Check your venting and lint basket. Check blower for lint build up and blower wheel obstruction., test by trying to turn the wheel manually by hand (should be easy) May have to remove cabinet or front/back plate to get to it) Next check the heating element itself with a meter for continuity it should show OHMS CLOSED CIRCUIT. If not its defective or has a short if its grounding out? Which in turns causes blown fuses or thermostats or overheating. The heating elements are located inside the heater ducts. If you think a heating element is faulty, test it with avolt-ohm-multimeter (VOM)set to the RX1 scale at 20K ohms. Disconnect the leads from the power terminals and clip one probe of the VOM to each terminal. The meter should read about 12. (1200) ohms. If the reading is higher ohms, the heater is faulty and should be replaced. Replace a faulty heater with a new one of the same type and electrical rating. A heater connected to a 115-volt line usually has an 8.4-ohm resistance; a heater connected to a 220-volt line usually has 11 ohms resistance. Check dryer Terminal block prongs both outside prongs should give combined 220, and 110 each if u check 1 outside & 1 center (ground) prong. Also check house electrical outlet for full voltage. 220 because if u only get half or 110 volts you will be able to run the machine which uses only 110 to run motor but not the heater which uses a full 220, OR you may have a broken centrifugal switch in the motor because this switch activates the motor and the heater as well. supposed to be if the motor does not run, the heater should not heat in order not to create a fire but if the motor is not running, and the heater is still heating, then there could be a problem with the motor centrifugal switch that is connected to this interlock switch that should trigger the heater. Check the thermal cut off, the cycling and the hi limit thermostats. For continuity or OHMS. If no ohms or resistance they need replacement. In some dryer's the control panel relies on a thermistor rather than a CYCLING thermostat to regulate the drum's air temperature by monitoring the component's resistance changes; resistance goes down as temperature increases and up when temperature decreases. Once the drum's air temperature reaches a certain level required to dry clothes, the control panel shuts off the heater. The panel will turn the heater on again and begin another heating cycle when the thermistor indicates that more heat is needed to keep the air temperature constant inside the drum this is why in some cases the dryer will operate at lower cycles like gentle or low heat but not at higher settings?) Lastly check your moister sensor. ( located inside the dryer door usually) Especially if machine seems to shut down early and clothes are still wet. Test with a meter at room temperature and it should show continuity. A failed moisture sensor will affect the dryer run time in the automatic moisture sensing cycle but it will not affect the heating of the dryer or the timed cycle. Which are reflected by the thermostats. Read more : https://www.youtube.com/watch?v=wVTBrGMql7g http://www.ehow.com/info_12203962_check-dryer-thermistor. GOD IS So GOOD !!!! AND THAT'S WHY MY ADVICE IS FREE https://www.youtube.com/watch?v=MMP7BW1lLs4 vent tube bad -undefined-undefined-0_6.jpg venting in cabinet clogged-undefined-undefined-1.jpg venting in cabinet clogged-undefined-undefined-2_4.jpg blowe housing lint build up-undefined-undefined-3.jpg blowe housing lint build up-undefined-undefined-4.jpg blowe housing lint build up-undefined-undefined-5_0.jpg fusesonroundelement-undefined-undefined-6_0.jpg fusesonroundelement-undefined-undefined-8_0.jpg fusesonroundelement-undefined-undefined-7_0.jpg fusesonroundelement-undefined-undefined-9_0.jpg
8/17/2021 6:54:19 AM • Dryers • Answered on Aug 17, 2021
0helpful
1answer

MY MODEL BCF-0019X2 FAN WITH LIGHTS QUIT

I replaced the battery and confirmed the codes are the same but still nothing. the light comes on and off only by the wall switch. is it likley that the part that holds the code in the ceiling needs to be replaced? the remote shows the red light when depressed so that appears working.
8/16/2021 1:49:19 AM • Dryers • Answered on Aug 16, 2021
0helpful
1answer

Model dv328aew/xaa does not start

Electric dryer no start does nothing Check dryer Terminal block prongs both outside prongs should give combined 220, and 110 each if u check 1 outside & 1 center (ground) prong. Also check house electrical outlet for full voltage. CHECK THERMAL SHUT OFF THERMOSTAT USUALLY LOCATED ON THE BLOWER. for OHMS or resistance with a meter. Should show a closed circuit. Ohms WHEN THIS FUSE BLOWS IT WILL SHUT DOWN EVERYTHING. NEXT Test the PUSH start switch with meter for OHMS. Should show OHMS when pushed in or on start, and no ohms or infinity when in off position. If you hear a humming/clicking sound from motor area you more than likely have a bad motor. Try this test out to see if u have weak windings or relay/capacitor on motor. Open the dryer door and turn by hand the drum while machine is on ON position. And you or someone else presses the door engagement switch in. If it starts up then u have bad windings Another thing to check is the belt safety switch. With a multi meter. Especially if u just replaced the belt. The belt safety switch is attached to the Tensioner and motor. IT LOOKS LIKE A DOOR SWITCH SOMEWHAT a little black pc of plastic with 2 prongs going into it. Sits at bottom of motor. Under the Tensioner. Attach meter clips to the 2 prongs on switch, Then when the little white push button is pressed in it should show continuity and none when released. Lastly check ur DOOR SWITCH for continuity with a meter when the button is pushed in the (on/Door closed position,) it may have gone bad. https://www.youtube.com/watch?v=MhVUEhngZMg https://www.youtube.com/watch?v=9xD7lCXJ0ZM https://www.youtube.com/watch?v=sTRP6kHqAFs Hey GOD IS GOOD !!!! WHICH IS WHY MY ADVICE IS FREE DRYER OVERHEATING: Heating Element A defective heating element can make a dryer too hot or not heat at all. . If the element partially shorts out, it can produce heat all the time, regardless of whether the dryer is calling for heat. Remove the heating element to inspect it. The coils should not be touching each other or anything else. Other Causes and Conditions Air Flow Problem Dryers need good ventilation to work properly. If the vent is clogged it can make the dryer too hot. Clean all of the vent tubing thoroughly. Cycling Thermostat Although not common, a defective cycling thermostat can make the dryer too hot. The cycling thermostat is supposed to turn on and off the heat to maintain the proper temperature. If the thermostat is defective it may keep the heat on too long. The thermostat is not adjustable or repairable, it must be replaced. HI LIMIT THERMOSTAT DEFECTIVE? SHOULD SHOW OHMS AT ROOM TEMPERATURE Felt Seal Most dryers have a felt seal at the front and rear of the drum to keep the heat inside the drum. If the felt seal is worn away or missing, the dryer may keep heating and make the dryer too hot. This is not common. Blower Wheel A defective blower wheel will not spin properly and will not vent the hot air, making the dryer too hot. Check to see if there is adequate airflow out of the dryer. https://www.youtube.com/watch?v=3m5NZvY9V5Q GOD IS still GOOD !!!! SO MY ADVICE IS FREE blower insides07-undefined-undefined-0.jpg backofdryer-undefined-undefined-2.jpg bypass-lid-switch-unplug - 5-undefined-undefined-4.jpg fuses dryercyclingfuse-undefined-undefined-7_1.jpg fuses dryercyclingfuse-undefined-undefined-8_1.jpg fuses dryercyclingfuse-undefined-undefined-9_1.jpg
8/15/2021 11:19:40 AM • Dryers • Answered on Aug 15, 2021
0helpful
1answer

GEW9868KQ2 Calypso. Why doesn't timed dry turn off? Dryer heats and turns, but only on timed dry.

ELECTRIC Dryer no heat or little heat, or shuts down to fast: Check your venting and lint basket. Check blower for lint build up and blower wheel obstruction., test by trying to turn the wheel manually by hand (should be easy) May have to remove cabinet or front/back plate to get to it) Next check the heating element itself with a meter for continuity it should show OHMS CLOSED CIRCUIT. If not its defective or has a short if its grounding out? Which in turns causes blown fuses or thermostats or overheating. The heating elements are located inside the heater ducts. If you think a heating element is faulty, test it with avolt-ohm-multimeter (VOM)set to the RX1 scale at 20K ohms. Disconnect the leads from the power terminals and clip one probe of the VOM to each terminal. The meter should read about 12. (1200) ohms. If the reading is higher ohms, the heater is faulty and should be replaced. Replace a faulty heater with a new one of the same type and electrical rating. A heater connected to a 115-volt line usually has an 8.4-ohm resistance; a heater connected to a 220-volt line usually has 11 ohms resistance. Check dryer Terminal block prongs both outside prongs should give combined 220, and 110 each if u check 1 outside & 1 center (ground) prong. Also check house electrical outlet for full voltage. 220 because if u only get half or 110 volts you will be able to run the machine which uses only 110 to run motor but not the heater which uses a full 220, OR you may have a broken centrifugal switch in the motor because this switch activates the motor and the heater as well. supposed to be if the motor does not run, the heater should not heat in order not to create a fire but if the motor is not running, and the heater is still heating, then there could be a problem with the motor centrifugal switch that is connected to this interlock switch that should trigger the heater. Check the thermal cut off, the cycling and the hi limit thermostats. For continuity or OHMS. If no ohms or resistance they need replacement. In some dryer's the control panel relies on a thermistor rather than a CYCLING thermostat to regulate the drum's air temperature by monitoring the component's resistance changes; resistance goes down as temperature increases and up when temperature decreases. Once the drum's air temperature reaches a certain level required to dry clothes, the control panel shuts off the heater. The panel will turn the heater on again and begin another heating cycle when the thermistor indicates that more heat is needed to keep the air temperature constant inside the drum this is why in some cases the dryer will operate at lower cycles like gentle or low heat but not at higher settings?) Lastly check your moister sensor. ( located inside the dryer door usually) Especially if machine seems to shut down early and clothes are still wet. Test with a meter at room temperature and it should show continuity. A failed moisture sensor will affect the dryer run time in the automatic moisture sensing cycle but it will not affect the heating of the dryer or the timed cycle. Which are reflected by the thermostats. Read more : https://www.youtube.com/watch?v=wVTBrGMql7g http://www.ehow.com/info_12203962_check-dryer-thermistor. GOD IS So GOOD !!!! AND THAT'S WHY MY ADVICE IS FREE https://www.youtube.com/watch?v=MMP7BW1lLs4 test dryer element-undefined-undefined-0.jpg vent outside dryer vent buildup-undefined-undefined-2_0.jpg vent tube bad -undefined-undefined-5_2.jpg fusesonroundelement-undefined-undefined-9.jpg blower insides07-undefined-undefined-13.jpg
8/15/2021 11:16:21 AM • Dryers • Answered on Aug 15, 2021
0helpful
1answer

Girbau dryer 100 on display won't do anything!!!

Bad display board
8/12/2021 4:49:46 PM • Dryers • Answered on Aug 12, 2021
0helpful
1answer

Beko DPU8360W dryer stops every 12 minutes

A GOOD LOCAL REPAIR SERVICE
8/11/2021 7:12:55 AM • Dryers • Answered on Aug 11, 2021
0helpful
1answer

How to replace the heat element Jojirushi BB-PAC 20

PAY A LOCAL REPAIR SERVICE TO DO IT
8/11/2021 7:12:38 AM • Dryers • Answered on Aug 11, 2021
0helpful
1answer

Dryer stops running before clothes are dry and will not restart until it cools down?

You did not post the make and model number but the problem is the thermal protection in the motor area. The motor area on most driers is under the drum and the front lower panel is usually removable. Unplug the drier and remove the panel and look in that area with a flashlight. You may have a lot of lint debris in there. Contrary to popular belief, dryers are not maintenance free. Get a vacuum cleaner hose and clean that area thoroughly.
8/6/2021 3:27:16 PM • Dryers • Answered on Aug 06, 2021
0helpful
1answer

What size screws are used on the HE2 dryer baffles

Well it looks like your mystery make dryer may be a Kenmore?? Repair Clinic will sell you the screws. https://www.google.com/search?q=Kenmore+HE2+dryer+baffle+screws ..
8/4/2021 10:53:03 PM • Dryers • Answered on Aug 04, 2021
0helpful
1answer

We have a Defy DTD315 tumble dryer. The power is on. When you press start, your hear the starting noise, but the drum never starts to turn. Almost if it is stuck somewhere?

Most common fault is broken or snapped drive belt. Control wise, most dryers will not spin if the control system detects that the door is not fully closed or properly locked. And also when the drain valve failed to open.
8/4/2021 2:53:04 PM • Dryers • Answered on Aug 04, 2021
0helpful
2answers

How can I replace a dryer knob shaft?

Whole switch has to be replaced.
8/2/2021 6:40:09 PM • Dryers • Answered on Aug 02, 2021
0helpful
1answer

My poweroll 2 electric roller will not activate

My button on my powerroll top o matic 2 will not make a sound or nothing it's all lit up but wont roll a cigarette I cleaned it out still nothing what would cause this?
8/2/2021 5:23:23 PM • Dryers • Answered on Aug 02, 2021
0helpful
1answer

I want to only dry the cloths how can I do it in AWD 129

Read the user manual. https://www.manualslib.com/products/Ariston-Awd-129-2777661.html
7/30/2021 7:16:33 AM • Dryers • Answered on Jul 30, 2021
0helpful
1answer

My Samsung 2018 DVE45N5300F/A3 dryer drum turns when dryer is off and door shut!

Probably a faulty microswitch/sensor. Call the engineer for a service.
7/30/2021 6:33:07 AM • Dryers • Answered on Jul 30, 2021
0helpful
2answers

New GE front loader. What causes a very loud metal on metal sound when drum spins?

A factory defect or drum bearing failure
7/28/2021 6:10:53 PM • Dryers • Answered on Jul 28, 2021
Not finding what you are looking for?
Bionaire BW2300 Window Mount Fan Logo

Popular Tags

15 questions posted

Ask a Question

Usually answered in minutes!

Top Bionaire Dryers Experts

Brad Brown

Level 3 Expert

18821 Answers

ray gallant

Level 3 Expert

73505 Answers

Kardoc

Level 3 Expert

6126 Answers

Are you a Bionaire Dryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Bionaire Dryers

  • Bionaire Dryers

Most Popular Question

problem

  • Dryers
Loading...