20 Most Recent Bionaire BCH-4138 Ceramic Compact Heater - Page 6 Questions & Answers

Just went through this after replacing Carbon filters. There is a 250V 15A fuse on one of the circuit boards but, by far, the more likely problem is incorrect seating of the front cover after replacing the filters. On the lower right side of the front cover is a rod which must go into the hole and engages a pressure switch that will kill power if the front cover is removed. This can be checked just by looking into the right hand side with the front cover installed. Ten second fix.

Question edited for clarity. Bad luck, and the company will get some negative advertising by your question as this will end up indexed by Google. There are some vendors for spare parts. If it is just a multicore wire that was damaged, that is available by the foot. https://www.google.com/search?q=human+touch+ZERO+GRAVITY+G+2+remote+replacement ..

Greetings from Mississauga, Ontario! If it is construction Styrofoam it is a good insulator. Fill as best you can between the studwork and use spray foam to fill gaps. Then cover with drywall. Floor insulation and underfloor heating is a good way to keep the chill out. Frozen pipes and only caused by cold and draughts. Stay warm. ..

The only thing that would cause this is something in the circuit is pulling too much electricity through that transformer. So what is the transformer hooked to? Please post the make and model

Take the fan power switch apart and clean the 2 point contacts. Also clean the 4 male studs that the wires plug into. That should solve the problem.

Question edited for clarity, full 'make model (what it is)'. It may not have one

• Dual Powered - Hardwired or Battery

Their own manual is terrible, but it is Section 7 here Replacing the Batteries 1. Open the thermostat cover and locate the battery compartment door. 2. Remove the two "AA" alkaline batteries located in the battery compartment. 3. Install two new "AA" alkaline batteries into battery compartment. Make sure to match the positive (+) ends of the batteries with the positive (+) terminals located in the battery compartment. 4. Close battery compartment and verify that the low battery indicator does not appear in the display https://api.ferguson.com/dar-step-service/Query?USE_TYPE=INSTALLATION&PRODUCT_ID=3984136 https://thermostat.guide/proselect/proselect-pstsl21p52-2h-1c-programmable-thermostat-product-specification-guide/ ..

Check the breaker. They have a 5 year warranty.

Warranty - Franke HT-400 Installation Manual [Page 12]

ManualsLib https://www.manualslib.com > ... > Installation manual use, for a period of ?ve (5) years from the date of purchase. This warranty will be honored provided the HT-400. Heating Tank has been installed and ...

the 58-7958-4 is a Jobmate air compressor with a 3-gallon tank and a 1/3 HP motor. It has a model number of QLG160905BJ-076 G19-1D I could not find the exact part number for the motor brushes, but you may be able to find it on the label of the old brushes or by contacting Jobmate Product Support. You can also try searching for compatible brushes by using the model number of the motor or the air compressor. How to Replace the Motor Brushes on an Air Compressor (youtube.com)

From the owner's manual:

• Open front thermostat door and open battery compartment door.
• Install two new "AA" alkaline batteries. Locate the positive (+) ends of the batteries and match them with the positive (+) terminals located in the battery compartment. Close battery compartment.

Going by the photo of the thermostat, it looks like there's a finger recess or latch on the right side of the thermostat that you pull on to swing the front open. If there is unexpected behavior from the thermostat after replacing the battery, see the reset procedure in the installation section of the manual. Link to manual: https://thermostat.guide/proselect/proselect-pstsl21p52-2h-1c-programmable-thermostat-installation-guide/#battery-replacement

Question edited for spelling of 'Frigidaire'. Air Conditioner / Heat Pump? All question need full 'make model (what it is)' as first 3 words please. When was it last serviced, and cleaned? It may need a top up of refrigerant gas. I suspect what you posted as a model number is actually a Serial Number and it is from Month 5 (May) of 2022. It may be under warranty. https://www.google.com/search?q=KK5226151 ..

If he did the same thing I did, then its during the wifi reboot not a hard reboot. I can get to the function section but it only brings up 70 and 80 which I can change but it only goes to 76 and 83 which I have no idea what functions these are. Still stuck in wireless set up and cant exit out

No because it is a gas appliance and law states that gas appliances can only be worked on by gas certified service engineers. https://www.google.com/search?q=replacing+a+thermocouple+on+a+Teba+TFB21Y ..

Find a good local plumber and ask for his recommendation. He will know which ones he has installed and never had problems with and which ones are reliable. The four makes recommended by Jake are well established. I had an oil fired Worcester down in Cornwall and it was good. Jake Napier Mar 07, 2019 I would recommend a combi boiler from Ideal, Valiant, Baxi or Worcester. This article might help you out a little (spam) ..

I just bought several of the Honeywell CT410A electric baseboard thermostats. One was significantly out of calibration. There is no screw to calibrate the unit. With the cover removed, pull the large adjustment knob straight off. Be careful not to touch or put pressure on the metal thermostatic plate which would bend it. I found pulling evenly with two hands, from each side pops it off cleanly. It is tight and requires more force than it seems. With the knob off, note that there is a smaller toothed dial which the larger knob clips onto. Turning the toothed dial, presses or releases the thermostatic plate, which activates a switch beneath the plate. Turning the dial slightly, you can hear the switch activate/deactivate. Set the dial so the switch just deactivates. Check your room temperature with a thermometer, and replace the larger knob onto the dial at the same temperature as the room. You will need to put the cover with the temperature gradients back on and mark the small dial for a accurate calibration before replacing the large control knob.

It would either be the spark igniter or the gas valve safety thermocouple. Call for service, as only gas certified technicians can legally work on gas appliances. https://www.google.com/search?q=Lexaire+9.0+M+reasons+why+igniter+will+not+light+on+furnace ..

copy and paste https://www.appliancefactoryparts.com/search/part/2930356/134267/

Question edited for clarity. That sounds like a fan issue. It isn't blowing hard enough so it cuts out on overheat and smells of burning dust. ..

Question edited for clarity and fix all the typos. This appears to be Australian? We are in North America, so this might work better for you. Unless is is an evaporative cooler, you don't put water in them. https://www.manualslib.com/manual/982146/Convair-Supercool.html#manual https://www.google.com/search?q=Convair+KYR32XC++%28co2%29 ..

Check the Power Connection: Ensure that the heater is properly plugged in to a standard electrical outlet. If the outlet has tripped, reset it to restore power to the heater . Thermostat Fuse and Resistance: You mentioned that the thermostat resistance is very low. This could be a sign of a faulty thermostat. Replace the thermostat fuse if it's burnt out. Make sure to connect the wires tightly. Use a multimeter to test the thermostat. It should read less than 1 ohm. Safety Features: The Pelonis HO-0221 includes safety features such as a thermal cut-off. If the heater overheats due to abnormal conditions, it will shut off automatically. If the heater turns off unexpectedly, inspect and remove any objects near it. Allow it to cool before resuming normal operation. Reset the Heater: Sometimes a simple reset can resolve issues. Follow these steps: Turn off the Pelonis Heater and unplug it from the power source. Leave the heater unplugged for 15 minutes to cool down completely. Plug it back in and turn on the heater.

You can, in some cases, hear the hiss of the gas on the mixture pipe. Quite normal.