20 Most Recent GE Profile PDW8400J Built-in Dishwasher - Page 2 Questions & Answers

You have a bad control pc board.

Hi

Dishwasher not draining issue usually occurs due to kinked drain pipe, clogged drain filter or drain pump. Check the drain hose for any visible clogging, remove if present. If no visible lint is present then remove then turn off the dishwasher and remove the drain hose and check for any visible clogging. If still not visible then the drain filter or drain pump is clogged and you'll need to clean the drain filter and drain pump.

Please note that dishwashers don't drain out the complete water such that heating element doesn

You have the control lock activated. Press and hold the heated dry pad for 5 seconds and it should unlock it

Check to see if the nut that holds the arm to the shaft is loose.Check to see that the arm is not jammed with something.

Hi,
There are three common problems that cause the Soap Dispenser or Cup not toopen. I have a tip that will explain these problems in detail....

Dishwasher Repair Problem Detergent Cup does not Open

heatman101

;


';;
';';

Hi, I have an older dishwasher also and recently mywife also complained about it not cleaning right... so me being the man I amtried in vain to clean the things... Bought new spray arms online and installedthem in minutes...now the thing works like new... However I have also foundthat if the heating element goes bad then that also can mess things up bad...So I would buy new spray arms, and also check out the heating element to makesure it is working... Here is a tip that will help you with the onlinebuying...
Dishwasher SprayArms not Spinning

How to Buy ApplianceParts Online

A bad heating element causes many problems in dishwashers...

Dishwasher Problems The HeatingElement not Working

DishwasherMaintenance DishwasherResidue and Film on Dishes

heatman101

Asker's Testimonial "explanation very clear. will give it a go and see howsimple it was. thanks Ronnie " - ronnieshomes

Hi

The issue seems to be with the float switch assembly that is bad and should be replaced. Float assembly is found inside the dishwasher's tub, on the bottom. The water that fills your dishwasher lifts the float, and when it reaches a certain level, it acts as a trigger for the float switch. The float triggers the float switch to shut off, thereby shutting off the flow of water into the dishwasher. A defective switch may interfere with your dishwasher's filling and/or draining ability. Use your voltmeter to test the switch. Set the device to the ohms setting x 1. Take each probe and touch them to one switch terminal each. This should produce a reading of either zero or infinity. Continue to touch the probes to the terminals, and press down on the switch's button. The reading should change to the opposite extreme. If your switch fails either of these tests, you should replace it. Hope this helps...please post back for further assistance.

Daniel

Hi,
Here is a tip that I wrote that will help you with your dishwasher not drainingproblem...

Dishwasher Problems - Waterwill not drain out

heatman101

Remove the bottom strainers and make sure that there is nothing obstructing the outlet pipe and the pump. If possible back flush through the outlet pipe and try draining the machine again before using it again. Also check that the valve that controls the directional flow of the water is operating. This too is in the bottom of the machine.

Hi,

The scum, film and white residue problems have started since the reduction of phosphates in dishwasher detergents.

Here is a tip that will help you to solve the problem of films, residue, and scum in your dishwasher.

Dishwasher Residue and Film on Dishes

heatman101

Clean out the holes on the spray arms, or replace the spray arms.

Same as above problem: I have had this dishwasher for less than 4 years and the dishes as of about 2 years ago stopped getting cleaned. I use the recommended dish liquid and rinse and lightly clean the dishes before I put them in.
What a piece of junk!! gs

Sorry to hear your having problems with your new dishwasher. Please review your owners manual for great tips for the best results on cleaning your dishes. Here are a few steps to take to get your dishwasher working:

1. Run you sink water for 3 min on hot before you start your dishwasher. This allows warm water to enter the dishwasher and helps aid in sanitizing and cycle time. Remember water entering must be at 125 degrees.
2. If your using power detergent be sure to use rise aid. All new dishwashers require this additive for best results.
3. If you have hard water your going to need a dishwasher cleaner and use it once a month. I recommend dishwasher magic. Kills 99.9% bacteria and leave a great scent. I use it myself.

Hi,
Here is a tip that I wrote that will help you with your dishwasher not drainingproblem...

Dishwasher Problems - Water will not drain out

heatman101

take a look at www.applianceart.com, they have a huge selection of dishwasher cover panels

drain pump either disconnected or jambed