Sabre LCT371BKA LCD TV - Answered Questions & Fixed issues
Sabre 37in multisystem TV has
TV's operate on 110 volts, not 220 volts. You need more than just an adaptor to plug in your TV. You need to use a voltage converter to bring the voltage down to 110 volts. But since you already connected your TV up to 220 volts, damage has already occurred to the sensitive electronic components and you need to get it repaired.
Red light blinking. How to stop it.
These blinks [flashes] are fault indication (Error Codes). From the number of blinks occur at one time switch ON, you can get an idea about the faulty circuit section inside it. This will make repair easy. These are called blinking codes. Make sure about the exact number of blinking of the standby/power LED, by switching On & OFF the set, for at least two times. Count it carefully. If you wish to get some details, check the site linked here. It has details about blinking codes, and fault locating procedure, to many popular brand TVs and other devices.
http://electronicshelponline.blogspot.com/
Blinking codes details to many popular brand TVs are given. Surf the site with patience.
37 remote code
0093,0048,0027. Try these codes. If
you wish to get some details, check the sites linked here. Set-up code list, and Set-up procedure to
many popular brand remote controls are given.
http://electrohelponline.blogspot.com/ http://remotesearch.blogspot.com/ Selecting the view option, either to
Mosaic
/ Timeslide, can be selected by the
drop-down list, at the top left
of the display window, will make surf easy. You can also do a
search, by type in the
brand name of your TV / Device, in the search box
at the top right of the display window.
The picture is shifted to one side. I have tried
It sounds that the software loaded has been corrupted by anyway. If so, a software update might be necessary. If you wish to get more details, check this link. It has details about software upgrade. Go through it, and if you're confident, do a software update. If not, contact any service technician.
http://electronicshelponline.blogspot.com/
Pull up previous posts by its left sidebar, or
type in the
brand name and model number to of your set, to its
search box, and press '
Enter' or view it in
Mosaic /
Timeslide option.
Remote control codes for sabre tv
When are you people going to learn. The only way you will get it to work is to find the same remote that come with the tv, That is what happens when you buy unknown brand (Electronics) Not evan a good universal remote will work on them, Stick to a known brand.Like jvc,sony, toshiba,lg,panasonic. Then you won,t have that problem. If the dog ate your remote,Because you for got to (Feed) it.
The sound on my tv went out. I tried basic
I would say not both speakes never go at the same time ver very rare. I would say the volume potientmeter is probably gone . You can tell if the speakers are toast by testing the ohms when unplugged Should be either 4 or eight ohms,could be two but they should be the same no matter. If you know how to jump across the amplifier leads try that just momentaryly of course and that is probably the guy. jumper across the digital pot to see if its bad you should get something . Are you sure your mute isnt on ,a stuck button or somerthing on the remote. try a different remote as well ,could be that
I have a 37 inch
First, look at the screen in darkened room to see if you can see any slight glow from the screen, if it does, then the problem can be the T-CON (not getting the 12vdc) or the main logic board not feeding the signals to the T-CON board.
if not, next place to check will be the power supply module, make sure it has 24vdc which is required by the backlight inverter to work, the reason for not having 24vdc can be from bad DC filter caps (leaking/bulging top, high ESR) or short circuits in the inverter board which will cause the 24vdc supply to go into shutdown mode, so you may have to disconnect the power cable that feed the inverter board to see if the 24vdc will work without the inverter board hookup, you will need to apply about 3~4 amp of load to the 24vdc to make sure it can handle that. There are fuses on the backlight inverter boards also. So there is some troubleshooting you will have to do to find out the causes of the problem you are having.
If you are going to DIY and have proper tools, electronics knowledge, and know safety precaution then please read on:
Basic LCD monitor and TV troubleshooting guide:
http://www.fixya.com/support/r5093881-lcd_flat_panel_tv_troubleshooting_guide
http://www.fixya.com/support/r6150077-basic_lcd_monitors_troubleshooting
http://www.fixya.com/support/r7406380-tv_training_manuals
Failed TV and Monitors: http://s807.photobucket.com/albums/yy352/budm
Learn about bad caps: http://en.wikipedia.org/wiki/Capacitor_plague
Parts: www.shopjimmy.com
Capacitors kit: http://lcdalternatives.auctivacommerce.com/Default.aspx he can make you a set of caps.
Or www.digikey.com, just make sure to use caps with low ESR, 105c, high ripple current and long life rating such as PANASONIC FM or FC series.
Please post back what you find. Please leave rating if it helps.
My Sabre LCD TV
My TV just did this 2 days before Thanksgiving. I just messed with it and fixed it today. Unplug it from the power source for atleast one hour. Plug it back it. Hold the power button til constantly flashes red and green. Wait at least one minute while it continues to flash. Turn it off. Flip the big power source button on the back to off && then on. Then hit the power button on the side, and it should turn on. Worked for mine. Hope it helps.
What is the sabre tv
The address I've found is: Sabre Electronics,
502 S Main Street, Saint Joseph, TN, 38481, United States Phone (931) 845 4465 I've found two web sites but both give me server not found errors. www.sabreelectronics.com/ and
http://sabrece.com/ .
Further research indicates the company filed for bankruptcy which is why the sites above don't work. I can't easily find the date of filing (probably 2007-2008).
I wish that I could be of more help.
Cindy Wells
Went to turn on tv and nothing happened and the
Unplug,replug the tv and cable box about an hour later,let the tv reset and the cable box upgrade it software,see any changes?No,take the tv aparts,u know basic electronic,have tools and basic soldering?The board,where the power a/c cord plug into it.That the power supply board.Searches for these parts call capacitors on the power supply board.They alway bulges up on it tops or puff up on it tops.These capacitors are leaking gases and dying.Replaced those dying leakages gases capacitors.Ur tv should have stable power now and work.Or tries websites like Shopjimmy.com,Ebay.com to buy a whole refurbish power supply board for the replacement.
Not finding what you are looking for?