20 Most Recent Electrolux EIFLW55HIW Front Load Washer with IQ-Touch Controls - Page 8 Questions & Answers

Broken actuator on lid?

Hi, Please recheck the documentation that came with the washer to ensure that you're attempting to place it in the manner intended by the manufacturer . Also, you can check the floor near the washer to ensure that no pieces have accidentally broken off from the front panel or dispenser as this would most likely stop you from making the attachment. If this issue persists, please schedule an appointment with your local Home Depot to fix to help overcome the issue at home. Thank you.

Hi, your exit valves might be a bit clogged. Please add 7 to 10 inches of tooth paste into a short wash and allow your machines pipes to be cleaned of it's potential debris that are clogging it's exit pipes. After this, please perform another wash. Thank you.

Hi, Please check the back and/or top of the object for any screws that you be remove before pulling out the drawer in the front. You can reference the user manual of the device to help guide you in the removal process. Thank you.

When you turn it on it should give you the 'E' and then a number. This number will show what the problem is likely to be. Comment below with the code and I'll try to help you more.

Hello friend, thank you very much for your inquiry!

After reviewing the information you have provided regarding your Electrolux front load washer EIFLW55HIW0 having an E35 error code, I have found E35 is an indication of a water over fill problem. If the water fills above 4.5 inches please follow the below trouble shooting steps I have provided for you. If the water is not above 4.5 inches you may need to change the pressure sensor switch.

If the water enters continuously please unplug the washer to see if the water stops. If the water does not stop your issue may be the water valve assembly. If the water does stop the wiring to the water valve assembly needs to be checked. If the wiring is good the control board may need to be replaced.

I do suggest you seek a professional technician to look into this issue further to avoid any unnecessary part purchases. - T

Hi. How to solve my washing machine front loader its always show error while im wash my clothes if i wash around 2 hours it will be stuck at 1hours 20 minutes. I have no idea why it happens like that.

Try disconnecting it from the mains supply overnight to reset. If it still does it, you need a service call. It is likely to be the Control Board and they are expensive so need correct diagnosis.

The senor on your washing machine could be broken now and needs to be replaced.

go to reset

Question edited for full make model (what it is) and English. Question moved to better category. Special problem for Indonesian machines https://www.google.com/search?q=Electrolux+W4600H+not+spinning ..

W4600h is washing but not spinning

Sounds like you did great job of following the service manual and advice for parts suppliers, but often, it is service tech knowledge that is useful. For instance they will look at a board and say "yes, this board fits most of them, but not yours", or they say "these boards are made on Taiwan for 5 bucks each and 8/10 don't work, I keep 20 in the van". also these days, techs carry a laptop computer and connect to a Service Port, like the OBD2 port on a car. The machine tells them the issue. Your choice, Service Call or Shiny New Machine. You can't do any more than you have done. you have obviously seen this, but did you check the connection to the Inverter board on the motor and the soldered joints behind the connection? Different model, same code.

E9F: Communication Error Between Main Board And Inverter ...

https://www.manualslib.com > ... > Service manual Electrolux EWM25 series Manual Online: E9F: Communication Error Between Main Board And Inverter Board. E9F Checks to perform: Measure the continuity between ...

the power surge might have ruined the relay or board

If it is new, contact the seller under warranty. This model is only available in Saudi Arabia, we are in North America. According to the specs, it is a condenser dryer with no vent to outside. These do take longer to dry, but they should dry eventually. https://www.electrolux.sa/en-sa/appliances/washer-dryers/eww1141aesa/#specifications ..

Check you have power to the cooker before you try anything else.

Get a flashlight and put it against the holes in the inner drum and you will be able to see what the object is. If you pull the door gasket down and away, there is normally enough room to slip in a straightened wire coat hanger to hook it out.

I would say you need the right part. Although they might look the same, the wiring to the pins might be different. Here is the part Fits your EIFLW55HIW0 Washer! Part Select Number PS2342436 Manufacturer Part Number 137038700 Manufactured by Frigidaire https://www.partselect.ca/PS2342436-Frigidaire-137038700-Drain-Pump-120V-60Hz.htm?SourceCode=20&SearchTerm=EIFLW55HIW0&ModelNum=EIFLW55HIW0&ModelID=1522373 I can't find the one they gave you. https://www.google.com/search?q=washing+machine+pump+%23137408 ..