Top 20
GE Profile JGS968 Gas Kitchen Range Questions & Answers
How do i remove the control panel? it does not work only displays time.
Take out the 4 burner knobs, just pull them straight out. Then, you'll see those round holders for the burner knobs, about 1 1/2 inches in diameter. They actually screw out, lefty-loosey, righty-tighty. Those 4 things are holding the control panel onto the oven, aka the keypanel. When you unscrew them, you should be able to pop the keypanel right off, depending on how strong the seal is (ours was worn and weak - 8ish years old I think). The problem you described sounds like the ribbon cable is unplugged, or has some gunk on it. A guy on Youtube says you can get the gunk off with a pencil eraser. Then carefully put the ribbon cable back into the slot on the back of the key panel, and put it back on the oven by lining it up and screwing in those black round holders for the burner knobs. You probably need to fix the seal on the keypanel so liquid/food doesn't spill in there; that's our next project (we don't use that range often.) Also, turn off the electricity and gas before you do this. (We flipped a switch at the circuit breaker to turn off electricity, but we didn't turn off the gas.) I'm not an expert, so please read safety tips in the manual before trying this. Good luck!
8/16/2014 2:48:43 PM •
GE Profile...
•
290 views • 0 helpful votes
Oven won't keep temp.
I would try another control board. I have gotten 2 new ones before that were bad right out of the box! It happens all the time.
12/27/2013 8:20:02 PM •
GE Profile...
•
85 views • 0 helpful votes
The flames from the front
The flames should be all blue - except when you first turn it on, where the flame begins, & only when you turn it on. Orange flames mean incomplete combustion is happening. Carbon monoxide is being released. Orange flames can also mean your getting low on gas. Clean it & try moving the disk around. An uneven disc means some flames will be higher & burn your pots. The flames are wrapping around your pots if they're burning on the sides. Keep flames under the pot. Regardless of the being clean, the odor means you need to check your gas level. Once filled back, the odor should be gone if that's the only problem. That is placed in the gas as a safety feature. Don't try to fix this problem yourself if the "easy" solutions don't work. It could be very dangerous. Invest in a carbon monoxide detector especially when you have anything gas.
9/15/2011 3:24:53 PM •
GE Profile...
•
559 views • 0 helpful votes
GE XL44 gas stove Model
oven wont light because the igniter isn't glowing bright enough. Just replace the igniter and oven will light.
3/30/2011 12:21:03 AM •
GE Profile...
•
1,278 views • 0 helpful votes
The touch pad is not
This
is your electronic control board that needs to be repalced on this
unit. GE Profile is a great brand and it is easy to repair, also.
We provide part removal/installation instructions for our customers when
you purchase your parts from us.We also ship parts overnight to assure
that you get your oven repaired right away.
Please contact us at:
http://www.fixya.com/repair/d499389-accurate_appliance_repair_service
from 7 AM until 9 PM CST. We look forward to getting you cooking again
soon.
6/19/2011 2:22:45 AM •
GE Profile...
•
65 views • 0 helpful votes
Getting error code F0 during oven cool down.
F0
Stuck touch pad Usually means that either the touch pad or the oven control
(also called clock or ERC) is defective and needs to be replaced. If this fault
code cannot be cancelled, replace the oven control (also called clock or ERC),
touch pad, or both.
1/31/2011 2:28:19 PM •
GE Profile...
•
532 views • 1 helpful votes
Just installed new control panel
Normally the bake/probe flashing happens when you plug in the probe. If
you don't have the probe plugged in, then double check that your wiring connectors are plugged in properly on your new board or that the wires to the probe connector are not shorted. Make sure that the probe is plugged in all the way. Unscrew the retaining nut, then unscrew the two sheet metal screws holding the housing in place, then give the probe connection a gentle tug to ensure that it is still properly connected.
12/22/2010 5:32:40 AM •
GE Profile...
•
500 views • 0 helpful votes
I have the dreaded F7 D6 Error message, tried the
Sorry to read about your problem, I hope this helps you out.
The "F7" fault code is indicating a shorted START key or a shorted
matrix. Determine if the problem is the key panel or the control board. since you replaced the clock, I would disconnect the ribbon connector and measure the flat
cable using an ohm meter. Allow up to 1000 ohms when pressing a key.
I tried to help you. Please help me and Rate/Vote on my response. We take the time to answer your question. take the time to rate us.Thanks and good luck
4 Thumbs - Very Helpful
3 Thumbs - Helpful
2 Thumbs - Somewhat Helpful
1 Thumb - Not Helpful
12/26/2010 4:22:46 PM •
GE Profile...
•
319 views • 1 helpful votes
Burners are working but oven is not heating just
Hello & Welcome to FixYa
This indicates a open/shorted oven temperature sensor and to solve this problem the sensor needs replacement. If you wan to be sure before replacing the sensor then you can test it with a voltmeter for around 1100ohms....if it reads more then this then it needs replacement however, if the reading is around or less then 1100ohms then it is the control board that needs replacement. Please get back to me if you have any other questions.
Kevin
1/11/2011 12:50:54 AM •
GE Profile...
•
114 views • 0 helpful votes
MY GE PROFILE RANGE OVEN
I have the same problem and GE has a technical memo out on this. It requires a programming change. Right now, I am trying to get GE to fix it at no charge, but so far, no luck.
8/21/2010 12:18:18 AM •
GE Profile...
•
583 views • 0 helpful votes
Not finding what you are looking for?