Top 20 GE 30 in. JGP337 Gas Cooktop Questions & Answers


Hi,
Some ranges have the conversion orfices right on board and for others you will need to order a conversion kit. Your manual will have the directions if the kit is on board. If there is no directions then look at most any of the appliance parts websites under your model number for the conversion kit.

heatman101

GE 30 in. JGP337... | 361 views | 1 helpful votes


I've seen this problem before. It happens when spillage get's into the ignitor switches. The switches are mounted on top of the gas turn-on valves. You have to replace all the ignitor switches because they are connected into wire harness. Rich

GE 30 in. JGP337... | 215 views | 0 helpful votes


Hi,
Here is a tip that I wrote that will help figure out why the burner spark keeps on clicking...


Gas Range Repair Burners Keep on Clicking
http://www.fixya.com/support/r4033033-gas_range_repair_burners_keep_clicking

heatman101

GE 30 in. JGP337... | 141 views | 0 helpful votes


take the part back and get the correct one. yours may have been packaged wrong

GE 30 in. JGP337... | 66 views | 0 helpful votes


You have one of your spark switches sticking. It may have come loose or possibly grease has migrated into it.
Remove the switch panel and check the switches for a loose or broken switch.
There is a switch behind every surface burner knob.
They must be seated firmly to work correctly.

GE 30 in. JGP337... | 183 views | 0 helpful votes


Hi,

Here is a tip that I wrote that will help figure out why the burner spark keeps on clicking...

Gas Range Repair Burners Keep on Clicking

heatman101

GE 30 in. JGP337... | 567 views | 0 helpful votes


Hi,
Here is a tip that I wrote to help people troubleshoot problems with their cooktops not igniting.

Cooktop Range Stove spark ignition does not work
http://www.fixya.com/support/r5649407-cooktop_range_stove_spark_ignition_not

heatman101

GE 30 in. JGP337... | 692 views | 0 helpful votes


You have a bad ignitor which will have to be replaced. Unplug one ignitor at a time until you find the faulty one.

GE 30 in. JGP337... | 398 views | 0 helpful votes


Hey y'all. I have the same lame GE profile gas cooktop with the gray grates and burner covers. I know this is the expensive way to go, but I use Easy-Off "self-cleaning oven" oven cleaning spray. For about $5, you get 3 cleanings. It is a pain to do, but I have better things to do than scrub these grates all the time. I don't know why, but the baked on crud just drives me crazy. I tried everything to clean them completely. I even tried to scrub the darn things with a kitchen pumice stone(sold at walmart)but it is impossible to get the curvy areas clean. Now the paint has started to wear off on the burner covers.

I do not use the oven cleaner on the cooktop itself. I use soft-scrub with baking soda, then cover the cooktop with a sheet of heavy duty aluminum foil and cut out holes for the burners. This keeps most of the spills contained, and helps with cleanup.

I visited to the GE parts web page, and they only sell gray grates and covers. I am going to buy black BBQ grill paint(spray can)from Home Depot and try it on the burner covers first. They are the least expensive to replace if it fails, and if it works, I will paint the grates with this high temperature paint. I will keep you posted on the results.

Regards,

Laura D.

GE 30 in. JGP337... | 4,735 views | 10 helpful votes


Call GE answer center 1-800-626-2000 aek for tech help. Have you Model # off your data plate ready.

GE 30 in. JGP337... | 160 views | 0 helpful votes


Unplug cook top. remove drip pan with screwdriver. Use hair dryer to completely dry area that might have gotten wet during cleaning. This may take five minutes. Put unit back together and plug in cook top.

GE 30 in. JGP337... | 168 views | 0 helpful votes


If you have recently cleaned unit and got moisture behind knobs, this may stop when the spark switches dry out. If not you will need to replace spark switches behind the knobs.

GE 30 in. JGP337... | 415 views | 3 helpful votes


Remove the burner knobs, inside of each shaft is a straight slot screw adjustment, use a flshlight to see it. Sears has screwdrivers this small.While holding the shaft with a pair of pliers turn the screw in the shaft, it will be hard to turn, this is normal.
Continue doing this until you obtain the desired flame setting.

GE 30 in. JGP337... | 552 views | 0 helpful votes


suspect problem is with the regulator on the gas bottle as it would be unusual for all burners to be faulty at the same time. try substituting a new regulator

GE 30 in. JGP337... | 202 views | 0 helpful votes


most likely the keypad is defective.

GE Cooktops | 186 views | 0 helpful votes


The induction cooktop will flash "F" when cookware has been removed from the surface; cookware is not present when the unit is turned on; or cookware is not centered on the element.
Position the cookware properly over the center of the cooking surface if the error code "F" flashes. Use only induction cookware and use a bigger pan, as the error code "F" indicates that the pan is too small for the cooking element.

GE Cooktops | 478 views | 1 helpful votes


There are several helpful how-to videos on Youtube but please be aware induction hobs work on a principle different from the usual and the troubleshooting and repair is considered a specialist task - if you wouldn't poke around inside a tv or a computer then you probably shouldn't poke around inside your hob.

GE Cooktops | 281 views | 0 helpful votes

Not finding what you are looking for?
GE 30 in. JGP337 Gas Cooktop Logo

27 questions posted

Ask a Question

Usually answered in minutes!

Top GE Cooktops Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Cindy Wells

Level 3 Expert

6199 Answers

Paul Carew

Level 3 Expert

3527 Answers

Are you a GE Cooktop Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

GE Cooktops

  • GE Cooktops

Most Popular Question

switch from lp gas

  • Cooktops
Loading...