20 Most Recent GE GBS18KBM Bottom Freezer Refrigerator - Page 3 Questions & Answers

Here are some possible causes and solutions to consider: 1. Check the temperature settings: Ensure that the temperature settings are set to the recommended levels for your refrigerator. You can refer to the user manual or manufacturer's website for the recommended temperature range. The target range is between 35-38°F 2. Clean the condenser coils: Dirty or clogged condenser coils can prevent the refrigerator from cooling properly. Clean the condenser coils located at the back or bottom of the refrigerator using a vacuum or brush. 3. Check the evaporator fan: The evaporator fan circulates cool air throughout the refrigerator and normally runs constantly. If it's not functioning correctly, it can cause the refrigerator to stop cooling. Check that the fan is running and for any obstructions or damage and replace it if necessary. 4. Check the door seals: The door seals ensure that the refrigerator is properly sealed, preventing warm air from entering. Check the seals for any cracks, gaps or damage and replace them if necessary. 5. On many Fridge Freezers, the cold air for the fridge is vented from the freezer side into the fridge. If the freezer coils ice up or block due to faulty defrosting, it can cause no cold air to reach the fridge compartment. 6. Checking the refrigerant gas levels: If the refrigerant levels are low, the refrigerator will not cool properly. Only qualified technician can check the refrigerant levels and add more if necessary. ..

This is a old post but may answer your issue....https://forum.appliancepartspros.com/posts/t537870-ge-profile-ice-melting-then-refreezingBest to you.The part i believe...https://www.partselect.com/PS2371164-GE-WR55X10996-BOARD-Assembly-MAIN-CONTROL.htm?SourceCode=20&SearchTerm=GFSS2HCYHSS&ModelNum=GFSS2HCYHSS&ModelID=1923343looks like you'll have to copy and paste.

B, Check here https://www.appliancepartspros.com/doors-parts-for-ge-zic360nmclh.html there's a video Hope this helps! Best to you

Question edited for clarity and toss in some CAPS. Yes, no problem as long as your splices are soldered and shrink wrapped to make them waterproof and safe.

The clicking sound you're hearing from the fan suggests that there may be an issue with the fan motor. It could be a faulty motor or a problem with the power supply to the motor. As for the light, it's possible that the bulb has burned out and needs to be replaced. Here are some steps you can take to troubleshoot the issue:

1. Check the power supply: Make sure that the unit is properly plugged in and that the outlet is functioning correctly.
2. Check the fan: Try manually turning the fan blades to see if they are stuck or obstructed. If they are, clear the obstruction and try again.
3. Check the fan motor: Use a multimeter to check the voltage going to the fan motor. If the voltage is not within the specified range, there may be an issue with the power supply or the motor itself.
4. Check the light bulb: If the fan motor is functioning properly but the light is not turning on, check the bulb and replace it if necessary.

If you are not comfortable performing these troubleshooting steps yourself, it may be best to contact a professional technician to diagnose and repair the issue.

If the defrost heater has blown twice in a short period of time and the coils are still freezing up, there may be an issue with the defrost thermostat or the defrost control board. Here are some steps you can take to troubleshoot the issue: Check the defrost thermostat: Use a multimeter to check the continuity of the defrost thermostat. If the thermostat is open, replace it. Check the defrost control board: If the thermostat checks out, the problem may be with the defrost control board. Check the board for any signs of damage, such as burned or broken components. If the board appears to be damaged, replace it. Check the defrost timer: If the thermostat and control board are functioning properly, the issue may be with the defrost timer. Use a multimeter to test the timer for continuity. If the timer is not functioning properly, replace it. It's important to use the correct parts for your specific model when replacing any components. Double-check that the replacement parts are compatible with your GE model. If you're unsure about the correct parts or how to make these repairs, it may be best to contact a professional appliance repair technician.

I assume you are referring to the water dispenser on your GE refrigerator. To turn off the water dispenser, you can either: Press and hold the "Lock" button on the control panel until the water dispenser display turns off. This will lock all the functions of the control panel, including the water dispenser. Locate the water shut-off valve behind the refrigerator and turn it off. This will shut off the water supply to the refrigerator and disable the water dispenser. Note: If you are trying to turn off the ice dispenser, the process may vary depending on the model of your refrigerator. Some models have a separate on/off switch for the ice dispenser, while others do not allow you to turn off the ice dispenser without turning off the entire refrigerator. Please consult your owner's manual for specific instructions.

If the auger motor won't turn by hand, it's possible that it is frozen and needs to be removed and thawed out. You can try spraying it with cooking spray after it's dried out to help prevent future freezing. Before removing the auger motor, make sure to unplug the refrigerator and turn off the water supply to the ice maker. You may need to remove the ice bin and any surrounding parts to access the motor. Once you've removed the motor, you can thaw it out by leaving it at room temperature or using a hairdryer on a low heat setting. Be careful not to overheat the motor. After thawing, you can test the motor to see if it's working properly. If the motor still doesn't turn, it may need to be replaced.

Yes, the WR30x10093 ice maker is compatible with the GE GTS22KHPARWW refrigerator as a replacement for the WR30x10012 ice maker. It is always recommended to double-check the compatibility with the manufacturer or supplier before purchasing a replacement part.

1. Open the dishwasher door and locate the screws on the inside of the door that hold the handle in place. There should be two screws, one at the top and one at the bottom.
2. Using a screwdriver, tighten both screws by turning them clockwise. If the screws are loose, this should fix the problem.
3. If the screws are tight and the handle is still loose, you may need to remove the handle and add a washer or two to create a tighter fit. To do this, remove the screws holding the handle in place and slide the handle off the studs.
4. Add a washer or two to each stud and slide the handle back on. Reattach the screws and test the handle to ensure it is now secure.
5. If these steps do not solve the problem, there may be an issue with the door itself,

It's possible that the main power source to the console has been disrupted, while the interior lights are on due to a separate power source. You may want to check the circuit breaker or fuse box to see if the circuit supplying power to the console has tripped or blown a fuse. It's also possible that there is an issue with the wiring or connection to the console, in which case it may be necessary to consult an electrician.

You must carry out the following procedures in order to remove the temperature control panel from a GE GDS18SBP refrigerator: Find the refrigerator's temperature control panel. Usually, it is near the top of the interior of the refrigerator compartment. The clips or screws holding the control panel in place should be removed. The back of the control panel is normally where these screws or clips are positioned. Carefully pull the control panel away from the refrigerator, being careful not to damage any wires or connectors. Once the control panel is removed, you should be able to access the defrost timer. The defrost timer is a small device that controls the defrost cycle of the refrigerator. It is typically located near the compressor or the evaporator coils. To change the defrost timer, you will need to remove the screws or clips that hold it in place, and then carefully disconnect any wires or connectors. Replace the old defrost timer with a new one, making sure to connect any wires or connectors correctly. Reinstall the control panel, making sure to secure it in place with the screws or clips. Once the control panel is reinstalled, turn the refrigerator back on and test the temperature control to make sure it is working properly.

There could be a few reasons why your GE ENERGY STAR 24.7 Cu. Ft. French-Door Refrigerator, Model #: GNE25JGKBB, won't go into Sabbath mode. You can try a few of the following: Control lock inspection Check to see if the control lock is off. You won't be able to switch on the Sabbath mode if the control lock is activated. Verify the water filter's condition: Verify that the water filter is clear and out of date. The operation of the Sabbath mode may be hampered if the water filter is blocked or past its expiration date. Verify the control settings: Make sure the appropriate control type is installed in your refrigerator. You should adhere to these directions for models with Figure B controls. Look in the manual: Verify that you are correctly adhering to the directions. Refer to the manual once again for additional thorough instructions if you need clarification on any steps or have any other concerns. Contact GE for more help if you've tried all the above suggestions but still have trouble turning on the Sabbath mode. They may need to send a professional to fix or replace the refrigerator, or they may be able to offer you further troubleshooting tips or steps. It's important to note that some models do not have sabbath modes without icemakers; if this is the case for your model, the sabbath mode option is unavailable.

shoud be amatter of pressing abutton and holding in for 3-5 secs to unlock. look closely at the control panel it should indicate which button(s)

The # 5 thermistor , pt # WR55X10025, located at the bottom of the freezer , slightly in front of the drain , with 2 white wires going to it , slid into a housing . This thermistor , is the freezer thermistor , which tells the control board , the freezer temp , when to cycle off , and is associated with the fan speed . The " breathing " sounds like the fan speeding up and slowing down . Replaceing this thermistor , should fix the problem .

If you have tried resetting the temperature settings to the default values and the temperature remains at -9°F in the fridge and 37°F in the freezer, there could be an issue with the fridge's cooling system. Here are some additional things to check: 1. Make sure the fridge is receiving power. Check to see if the fridge is plugged in and that the outlet is functioning properly. 2. Check the temperature control board. The temperature control board is responsible for regulating the temperature in the fridge. If it is faulty, it can cause the temperature to remain at a fixed, incorrect value. 3. Check the condenser coils. If the condenser coils are dirty or obstructed, it can cause the cooling system to malfunction and result in incorrect temperatures. 4. Check the door gasket. If the door gasket is damaged or not sealing properly, it can cause the temperature inside the fridge to become too warm. If none of these solutions fix the issue, it is possible that there is a problem with the fridge's cooling system. In this case, it is recommended to contact a professional appliance repair service for further assistance. Regarding the ice maker working intermittently, this could be caused by a variety of factors such as low water pressure, a faulty water inlet valve, or a problem with the ice maker itself. It is recommended to troubleshoot these issues separately.

first you gotta do is try to remove the thermostat, and then tap tap tap those sensors maybe it can help.. If not then contact a appliance technician

Hi, Please ensure that the door is properly closed and that there are no leaks. You can also ensure that the temperatures are no colder than is required to cool or freeze your food as a very low temperature would require more work/energy from the fridge. Lastly, you can power cycle the fridge once and if it continues with the issue, you can return it. Thank you.

possible door chime try to go into set up and turn off check to see if cold enough might be temp sensor

ice maker noise