20 Most Recent Hampton Bay 24002 Ceiling Fan Questions & Answers

0helpful
3answers

How do I get this fan to go faster its manual

Read the manual here is where you can download the manual Hampton Bay Ceiling Fan Manuals get-fan-go-faster-its-manual-1gdqw1qropftymekwmagzp34-3-0.jpg
3/14/2024 9:37:12 AM • Hampton Bay... • Answered on Mar 14, 2024
0helpful
2answers

Hampton bay ceiling fan

we have a hampton bay fan burning smell coming in didnot run
12/22/2023 7:11:50 AM • Hampton Bay... • Answered on Dec 22, 2023
0helpful
2answers
0helpful
1answer

Hampton Bay Midili 44-inch Indoor Brushed Nickel Ceiling Fan. Mount cover will not unscrew to get at the mounting bracket so we can remove the fan...HELP!

Question edited for a lot more clarity, full 'make model (what it is)'. Question moved from Cars and Trucks category. Did you undo the locking screws?

Midili 44 in Ceiling Fan Owner's Manual

homedepot-static.com https://images.homedepot-static.com > pdfimages Refer to the instructions packaged with the light kits and switches for proper assembly. 13. All set screws must be checked and retightened where necessary ... 29 pages .. Opposite of Installation
9/13/2023 11:40:56 PM • Hampton Bay... • Answered on Sep 13, 2023
0helpful
3answers

My ceiling fan "wobbles" when turned on. How do

Make sure ALL screws are tight, especially the set screws. Make sure the hanging bracket is tight against fan box. If your blade arms are bent, then you need a new set. Make sure blades are not warped. Other than that you can try a balancing kit as long as it's not that last two problems listed. This happens a lot with low-end store brand fans.
3/12/2023 2:48:51 PM • Hampton Bay... • Answered on Mar 12, 2023
0helpful
1answer

How to fix a wobbly ceilng fan

wobbly cieling fan1. make sure all mounting screws between the fan and the ceiling are tight. There is probably an electrical box mounted in the cieling that the fan is screwed into. I would turn the fan light on and then keep flipping breakers off, on at a time ,to see which breaker turns off the fan light. leave the fan light breaker off and you can unmount the fan from the cieling electrical box. The electrical box may have several holes in it for mounting screws and prehaps there are some holes left empty in the box that you can put more wood screws into to help keep the electrical box more firmly mounted and that may help lessen the wobble.Its ok to bend the electrical wiring aside to put more screws in. Just be reasonably gentle with the wiring and then bend it back somewhat to where it was before you started. make sure that wiring does not get pinched between the fan and the electrical box and that all wiring resides inside the box.#2 This is harder to do. you need to balance the blades for the fan ,similar to how a lawnmower blade is balanced after sharpening and before remounting the lawnmower blade on the mower. also kinda like balancing a car tire. I have a lawnmower blade balancing fixture that i bought at the lawnmower shop, but i dont know if there is a fan blade balancing fixture that you could buy from somewheres. Maybe try google.com,bing.com or ask.com and type into the search box fan blade balanceror fan blade balancing fixture or fan blade balancing jig.PLEASE read the directions or SPECIFICATIONS before you buy the fan blade balancer, only to find out that it only fits 9 inch diameter fan blades, and your blade is 2 4or 36 inches long.The balancer may have to fit a certain diameter hole at the centerof the fan blade. When you finally find out which side of the fan blade is heavy, you have to grind , with an electric grinding wheel, some material off the heavy side of the blade so that it is the same wieght as the light side of the blade.Try to imagine a cone shaped center[like step drills] like the capital letter V ,only up side down, so that the point is up. ON the underside of the inverted V is a needle tiped post that upside down V can pivot in any direction on. The hole in the middle of a lawnmower blade is centered somewheres on the outside of the inverted V, depending on the diameter of the hole in the lawnmower blade. The heavy side of the mower blade will go down and may touch the level asphault or the table top, depending on where you placed the balancing fixture. THen i would grind off metal until the heavy side can up to be level with the light side of the mower blade and it was considered balanced.an appliance repair parts store may sell fan balancers, but if the would fit your cieling fan, better ask before you waiste your money on something that wont work for what you want.Try calling up customer service of the manufacturor of your ceiling fan and ask about repair service for your brand fan.see what repair service has to say, im sure many others have asked them about wobbling fans.so they should have all the answers down pat.Two more thoughts.1. .MAKE SURE ALL SCREWS THAT HOLD FAN BLADES ON TO THE HUB ARE THERE AND are TIGHT. one loose fan blade mounting screw or one missing fan blade screw will unbalance the whole thing and cause wobble.2. the fan motor shaft bearing could be worn out or round or even egg shaped. If this is the cause, the motor must be diaassembled and new fan shaft bearings installed or the fan motor must be replaced. good luck and have fun!
2/16/2023 4:40:34 PM • Hampton Bay... • Answered on Feb 16, 2023
0helpful
2answers

Ceiling fan stopped turning

Usually the capacitor has burned out, and needs to be replaced.
Try going online looking at the manufacturers site and inquiring.
hope this helps
8/7/2022 3:48:42 PM • Hampton Bay... • Answered on Aug 07, 2022
0helpful
1answer

Wiring ceiling fans to wall switch

Hi Bigelow,

You need two switches.  It sounds like the Electrician set up the junction box for two circuits(Lights and Fans).  i say this because your supply has 4 wires, Red , Black, White and Bare. We may be able to oversome this with one Lutron Switch. Allow me to investigate, and I will be back.
8/7/2022 2:30:18 PM • Hampton Bay... • Answered on Aug 07, 2022
0helpful
1answer

Capacitor for ceiling fan burned out, just barely

model number is on top of motor facing ceiling
8/6/2022 4:17:17 PM • Hampton Bay... • Answered on Aug 06, 2022
0helpful
1answer

Wiring light kit to ceiling fan

connect the white wires from light kit filter to the white wire labeled "for light" from fan. then connect black wire from light kit filter to blue wire from fan. use wire nuts to make the connections
8/6/2022 3:32:50 PM • Hampton Bay... • Answered on Aug 06, 2022
0helpful
1answer

Trying to connect a ceiling fan light kit.

Those connections sound OK ,, now you have to go to the canopy and see if all the wires for the fan/light are connected to a house wire. If there are two switches , then the blue fan wire would connect to the red wire .. it may be capped off in the ceiling. If there is only one control switch , then the blue wire from the fan will connect to the same ceiling wire as the black fan wire does.

Please Vote !!
8/6/2022 3:19:56 PM • Hampton Bay... • Answered on Aug 06, 2022
0helpful
2answers

I need a replacement part for my ceiling fan the pc board

you can get info on how to get replacement parts here http://lightingworldbay.com/hampton-bay-replacement-parts/
7/22/2022 5:59:37 AM • Hampton Bay... • Answered on Jul 22, 2022
0helpful
1answer

How to wire up my ceiling fan?

Call an electrician for your own safety.
7/5/2022 11:33:17 PM • Hampton Bay... • Answered on Jul 05, 2022
0helpful
2answers

I need a wiring diagram of the Hampton Bay fan

Twist the bare conductors together tightly, matching the black and blue ceiling fan wires to the black power wire, and the white ceiling fan wire to the white power wire, don't forget the green ground !!
6/14/2022 9:03:58 AM • Hampton Bay... • Answered on Jun 14, 2022
0helpful
1answer

I rent an apartment equipped with two ceiling fans. I would like to purchase a remote for the fans. How do I go about this? Is there a generic remote for ceiling fans, like there is for televisions?

No there are proprietary to a make and a series of models. Also, not all of them remote controlled, none of my 4 are! Remote control fans are for where you can't reach and they usually have chains. Each one has to be paired to its remote using tiny DIL switches in the fan and the remote. Google make model replacement remote. The make model information is hidden inside.
4/23/2022 2:47:29 AM • Hampton Bay... • Answered on Apr 23, 2022
0helpful
1answer
0helpful
2answers

Two fans mounted close. Remote operates both at same time

Try using the remote much closer to one of the units at a time. If that doesn’t work you’ll have to do it manually or get a different brand for one fan.
7/12/2019 4:23:49 PM • Hampton Bay... • Answered on Jul 12, 2019
0helpful
2answers

Why do we run ceiling fans backwards in winter

That question cannot be answered as stated. What direction is backwards and what is the pitch of the blades. The theory now mostly dis-proven is you pull the hot air off the cealing in the winter to help warm the home. The opposit is valid in the summer. The amount of energy used is normally more then what is saved in the AC bill.
7/8/2019 6:53:37 AM • Hampton Bay... • Answered on Jul 08, 2019
0helpful
7answers

Cant remove Globe to change light bulb on Hampton Bay ceiling fan

twist counterclockwise (looking up at it) on glass firmly and carefully, the globe functions like a screw
5/19/2019 7:29:08 PM • Hampton Bay... • Answered on May 19, 2019
Not finding what you are looking for?
Hampton Bay 24002 Ceiling Fan Logo

550 questions posted

Ask a Question

Usually answered in minutes!

Top Hampton Bay Dryers Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Jose Ramirez

Level 2 Expert

264 Answers

Brad Brown

Level 3 Expert

19187 Answers

Are you a Hampton Bay Dryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Hampton Bay Dryers

  • Hampton Bay Dryers

Most Popular Question

midili 44 in mount cover will not

  • Dryers
Loading...