GE JKS05 Electric Single Oven - Answered Questions & Fixed issues


on the oven's smooth surface you should use a razor blade and scrap off the plastic (when cooled).. if the plastic melted on the burner, you may need to replace that particular element from a local appliance part store. easy to do.

GE JKS05... | Answered on Dec 18, 2014 | 358 views


As with all 240 volt appliances... if one breaker pops... you can't see it because it is a double breaker. You have to shut it down then turn it on. Ask again if it still doesn't work.

GE JKS05... | Answered on Oct 21, 2013 | 69 views


Component failure within Electronic Range Control (ERC) effecting temp processing circuits. Replace the ERC. Here is the part to order.





The part comes with a 365 day, any part, any reason return policy.

GE JKS05... | Answered on Dec 04, 2012 | 48 views


I have the exact same problem with my GE wall oven, my model number is JCKS05BA2BB. Is there a known fix?

GE JKS05... | Answered on Dec 01, 2012 | 301 views


Self cleans generally do a good ****on small messes in 2 -2.5 hours. Larger messes take 3. Leaving the racks in is okay...but they will likely lose their shiny appearance. Manuals are on the GE website.

GE JKS05... | Answered on Jan 17, 2012 | 3,097 views


We had the same problem with our GE Tru Temp Oven and the fix worked like a charm! Thank you for posting this fix - you saved our dinner party!

GE JKS05... | Answered on Sep 15, 2012 | 4,195 views


An error F7 on this model means there is an issue with the touch-panel. It might need to be replaced even if the error is intermittent. The ERC (an electronic clock controller) might also have issues by can diagnosed further if replacing the touch-panel doesn't completely solve the issue--however, it should.

GE JKS05... | Answered on Feb 28, 2011 | 138 views


We have a new GE Range and the signal beeps at about 100 degrees below the temp which we have set . The dealer replaced the sensor and the control circuit, but there was no change.
A service tech from GE came to our house and explained that the new ovens have a bottom heating element which is covered and therefore heats the lower part of the oven more slowly; but the exposed upper element heats more rapidly and the sensor is located near the upper element. We were advised to wait for about 15-20 minutes after the beep before placing the food in the oven. Judging from the number of comments found online, this seems to be a feature of newer ranges.

SnapDoc

GE JKS05... | Answered on Jan 28, 2011 | 224 views


Hi,
If your electric oven is taking too long to heat or just not heating up right,then check out this tip that will give more detail about your problem.

Oven Problems Electric Oven is Heating Slowly or Poorly

heatman101

GE JKS05... | Answered on Jan 06, 2011 | 79 views


YOU NEED TO REPLCE THE ERC KNOWN AS THE CONTROLL CLOCK

GE JKS05... | Answered on Dec 22, 2010 | 82 views


This is most likely a Thermostat/Temperature controller OR a Thermistor problem, first locate and replace the thermistor. If it still isn't going, then replace the Thermostat/Thermostat controller.
Below is a link for your manual.

http://www.fixya.com/support/p127014-ge_jks05_electric_single_oven/manual-12232/page-8

GE JKS05... | Answered on Dec 13, 2010 | 167 views


The problem is usually the igniter not reaching the correct amp draw .When the igniter does not reach the correct amp draw it may allow the gas valve to partially open or not open at all. The igniters are inexpensive and easy to replace. This video will walk you thru the correct procedure for testing an oven igniter. It may be a different model but the testing will be the same.You can also enter your model # for diagrams and illustrations of your specific model. Not all models are available. All parts come with installation instructions.

GE JKS05... | Answered on Oct 28, 2010 | 73 views


Hi, you need to have your control board rebuilt or replaced (if it's stll available). Here's an article I wrote on this failure last year if you want to read the details. http://appliancejunk.com/blog/2009/10/24/oven-failure-after-self-clean-and-f1-errors/

GE JKS05... | Answered on Aug 01, 2010 | 125 views


Usually this means a stuck key on the keypad. A tech can disconnect the keypad, then power up the oven. If no error code: problem with keypad, if still get error code: problem with electronic control.

best regards,
bruce
www.fixyourboard.com

GE JKS05... | Answered on Jun 19, 2010 | 304 views


reset the control panel or unplug the unit and wait and follow the directions in the manual this happens to me alot

GE JKS05... | Answered on May 17, 2010 | 116 views


Hi,
Cycling the power off and then on again will sometimes reset it...often you will have to call the customer service number to get the steps to take to unlock that...

Also check out this tip...

http://www.fixya.com/support/r3969401-self_cleaning_oven_problem

heatman101

GE JKS05... | Answered on Apr 26, 2010 | 125 views


self cleaning ovens stay locked til the temp goes down to a safe temp give it a little time

GE JKS05... | Answered on Apr 15, 2010 | 192 views

Not finding what you are looking for?
GE JKS05 Electric Single Oven Logo

85 questions posted

Ask a Question

Usually answered in minutes!

Top GE Ovens Experts

Michael Thomas
Michael Thomas

Level 3 Expert

3056 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

Cindy Wells

Level 3 Expert

6195 Answers

Are you a GE Oven Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...