20 Most Recent GE Profile JT912 Electric Single Oven Questions & Answers

I went out to my circuit breakers and turned the circuit off, let the oven cool, and powered it back up after about 2 hours. Fine now.

GE Profile JT912... | Answered on Mar 17, 2014

see this steps and fix it. God bless you

. Top element
If the element only works partially or not getting red hot at the "Hi" setting, the problem might be with a burned out receptacle that the element plugs into. If this is the case, replace both the element and the receptacle.

You can usually tell when the element itself burns out. It might have small holes or bubbles on the coil. Replace the element, if found defective.

2. Infinite switch
Another reason, why the element would not start, might be a defective infinite switch (located behind the control panel, with the burner knob on its shaft). Replace the switch if found defective.
Read more: http://www.appliancepartspros.com/repair-help/rangeoven-repair-help.html#2-2#ixzz2aSmUeYiW

GE Profile JT912... | Answered on Jul 29, 2013

major electrical problem. call a repair man asap!

GE Profile JT912... | Answered on May 19, 2013

Test Continunity for your Probe, if it has good continuity, then you have a internal issue with the Oven... More than likely, you are going to need a Technician

GE Profile JT912... | Answered on Apr 12, 2013

http://www.repairclinic.com/0078.asp#GE5, this site will give you the code and if your mechanically inclined you can do it your self ,but if the warranty isnt exspensive you might want that,but it is the keypad

GE Profile JT912... | Answered on Dec 14, 2012

Check your bake element. Unually ovens use both bake and broil elements to preheat and just bake element to keep temperature. Your bake element is probably burned out.

GE Profile JT912... | Answered on Jan 30, 2011

If your electric oven is taking too long to heat or just not heating up right,then check out this tip that will give more detail about your problem.

Oven Problems Electric Oven is Heating Slowly or Poorly


GE Profile JT912... | Answered on Jan 06, 2011

Could be a faulty control as you suspect but also may be a bad keypad. If the "start" button has no effect I'm suspecting the keypad first.

Best Regards,

GE Profile JT912... | Answered on Jun 19, 2010

there is a latch in the top of the door that locks in clean mode . need to get it out of clean mode

GE Profile JT912... | Answered on Sep 03, 2009

  • When the food you're baking is done on top but not on the bottom--or when baking just takes far too long to finish--the bake element may be burned out.

    You may get fooled into thinking it's working, because the oven is hot inside. But many electric ovens use the broil element, too, during the preheat and bake cycles. So the food may be getting heated only by the broil element, which causes poor baking results.

    If the bake element is burned out, replacing it should solve the problem. Otherwise, you need to further troubleshoot the oven's electrical system to locate the defective wire or component.

  • When the temperature is consistent but too high or too low, it could be one of several different things. First check to see if the thermostat sensing bulb has come loose from its holder. It could be lying on the floor of the oven or resting on the heating element. This would cause the oven to not heat correctly.

    If the thermostat bulb is not dislodged, it's likely that the thermostat or sensor is either mis-calibrated or defective.

    Electronic ovens with a digital display use a sensor to monitor oven temperature. To solve temperature problems for these models, you may need to replace the sensor. On some digital-display models, you can calibrate the temperature using the key pad. See your operator's manual for details.

    Ovens without a digital display often use a mechanical system for controlling temperature. On many of these units, you can remove the thermostat knob and adjust the knob itself to more accurately represent the actual setting of the thermostat.

    If, when you remove the knob, there's a screw on the back of it with a small calibration plate, you can loosen the screw, adjust the plate, then tighten the screw again. If the knob isn't adjustable, and the oven temperature is off by more than 30 to 40 degrees, you need to replace the thermostat to solve the problem.
  • GE Profile JT912... | Answered on Aug 14, 2009


    F9 means there is a problem with door lock circuit such as pinched wire between Electronic Range Control (ERC) and door lock switch. You need to check wiring and test operation of switch by following these steps:

    1. Disconnect power to stove
    2. Gain access to the back of the clock (electronic range control or ERC).
    3. Unplug the touch pad ribbon connector from the ERC. This will be a flat wire approx. 1 1/2" to 2" wide.
    4. Make sure everything is clear and will not short out when power is turned back on.
    5. Turn power back on to stove.

    If still the issue is not resolved then you have either a bad ERC (clock) or a bad touch pad and it needs to be replaced.

    Please do accept the solution if the issue is resolved or else revert for further assistance.


    GE Profile JT912... | Answered on Aug 10, 2009

    Go to this web site. You have to enter the entire model number in order to get your manual.
    Good luck and hope this gets it done for you

    GE Profile JT912... | Answered on Jun 27, 2009

    Not finding what you are looking for?
    GE Profile JT912 Electric Single Oven Logo

    35 questions posted

    Ask a Question

    Usually answered in minutes!

    Top GE Ovens Experts

    Michael Thomas
    Michael Thomas

    Level 3 Expert

    3056 Answers


    Level 3 Expert

    85239 Answers

    Cindy Wells

    Level 3 Expert

    6197 Answers

    Are you a GE Oven Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    View Most Popular

    GE Ovens

    • GE Ovens

    Most Popular Question

    r ni just bought house ge oven

    • Ovens