Top 20 GE Profile JT915 Electric Single Oven Questions & Answers

Hello & Welcome to FixYa

This indicates an open/shorted oven temperature sensor and to solve this problem the sensor needs replacement. If you want to be sure before replacing the sensor then you can test it with a voltmeter for around 1100ohms....if it reads more than this then it needs replacement however, if the reading is around or less then 1100ohms then it is the control board that needs replacement. Please get back to me if you have any other questions. Kevin

Hello there and thank you for choosing fixya
The f-3 code is a verry common code on ovens what this is telling you is that the oven temperature temperature sensor is not working correctly they normally will read the preheat then fail shortly after this and produce the code that you are recieving ok?
So you will first want to check to see that the temperature sensor is fully connected and is in good condition if it looks bad or full of grease or junk clean it and then try it again this may help but if not you will need to replace it ok?
Hope this is very helpful for you
Best regards Mike

Hi,

That is not that hard to fix and you can easily buy the parts yourself online...Here is a tip that will help you with the online buying...How to Buy Appliance Parts Online

Here is one site that I recommend

http://ping.fm/zJDAM

heatman101

Hello, Welcome to FixYa.

I'll start by saying on many models different issues can manifest a similar scenario, especially under the same manufacturer. For instance the error code "F0" on GE built ranges means either the timer/control is faulty or a key on the user interface/ketpad is stuck. There is a somewhat easy method to determine which is at fault though, if you are mechanically inclined, or even confident to pull the back off with guidance.
**Unplug the unit from the wall or turn off the breaker (40amps)...safety first**

The keypad connects to the timer by way of whats called a "ribbon connector" or "molex connector", if you disconnect the keypad from the timer then restore power wait at least 40-60 seconds and the "F0" returns, you need the control/timer. If no error occurs, re-connect the ribbon connector, restore power and then if the "F0" returns, its the keypad/control panel.

OVEN CONTROL/Timer


KEYPAD

Keep me posted as to what you find or if this is something you think you can or can't do. I'll await your next post and we'll go from there. I will help you in any manner I can of course. Thank you for choosing FixYa for your inquiry.

Regards,

Macmarkus :) -->

Hello,
It sounds as if an element in the oven is not working do check again that the oven thermometer is on same scale as the oven settings farenheit or centigrade.Most likely it is an element fault.
Hope I helped.

has the oven got a fan on it. if so then maybe fan is faulty.
if convection oven then maybe one of elements is faulty
or the thermostat is a problem
regards
richard saupe
Appliance repairman colchester

appliance repairman

use stop/clear reset clock then

I think your ignition does not work.
Is this a brand new oven ?
Does it have a stove on top ?
does the stove work ?

I am by no means an expert, but I believe the only thing differenty in a convection oven vs a regular oven is that there is a fan to conduct the heat quicker and more evenly. It has to do with heat tranfer rate. I can't imagine why aluminum foil would cause any problem.

Sounds like a bimetal switch is blown. first I would check SWITCH LIMIT BIMETAL next the LIMIT SWITCH-UPPER(LOCK) Too check them first trip the breaker so you don't have power to the oven, then you will have to take the oven out of the wall..next remove the top cover. then in the center-front there are two round bimetal switchs with two wires coming out of them..remove the wires and check them with an ohm meter both should have continuity across them ...if no continuity you have a bad switch. let me know what you find out..

1-800-gecares

Never ever use the Self Clean feature. All it exists to do is to keep the makers in a steady stream of sales of spares. The temperature is 800 to 925'F. The parts can't handle it. Try turning off at the breaker overnight to reset.

Why You should Never Run A Self Clean Oven Cycle & A ...

General Appliance Service https://www.generalappliancesvc.com > why-you-should... Jan 29, 2020 - A self-cleaning oven is a feature on many modern ovens that burns off cooking spills and splatters with an extremely high temperature (932 F° or ...

Self-cleaning oven

Wikipedia https://en.wikipedia.org > wiki > Self-cleaning_oven A self-cleaning or pyrolytic oven is an oven which uses high temperature (approximately 932 °F (500 °C)) to burn off leftovers from baking, without the use ... ‎Pyrolytic process · ‎Alternative technologies · ‎Catalytic cleaning

Self-Cleaning Oven: 6 Reasons to Stop Using Feature ...

FIX Appliances CA https://fixappliances.ca > 4-reasons-stop-using-self-cleani... Feb 2, 2024 - Auto-cleaning, also known as "pyrolytic cleaning," operates by heating the interior of the oven up to 500?C. During this process, grease is ... ‎How Self-Cleaning Ovens Work · ‎Major Parts Damage ..

You remove the door and then split the inner and outer parts of the door. clean the glass with Easy Off spray, rinse well, polish and put it back together. The videos should help as they all work to a theme.

How to Clean Oven Glass-Inside, Outside, and In Between!

The Happier Homemaker https://thehappierhomemaker.com > Recipes > Cleaning Aug 24, 2022 - Spray outside glass with vinegar and wipe down with paper towels. · Clean inside of the oven glass with a scouring pad using the "hack" below. ..

The fuse for a GE Profile electric range model JBP79A0B2AA is usually located behind the control panel, near the power cord. You may need to use a putty knife or thin flathead screwdriver to gently pry the control panel away from the wall before accessing the fuse.

My advice is get rid of it. Or test every joint with washing up liquid and water in a spray bottle. This is what a gas explosion can do to your house. Our windows rattled 2 km away! https://www.google.com/search?q=mississauga+Hickory+Drive+gas+explosion ..

Refer to page 40 to 44 (Troubleshooting Tips) of manual L0707187 (searspartsdirect.com)

Cynthia, I've gone thru the manual here.... https://www.searspartsdirect.com/manual/42qc2frzjh-000432/ge-jgb900sel2ss-gas-range-parts And there doesn't appear that the "beeping" can be disabled. You may try contacting them..... MAJOR APPLIANCE QUESTIONS. GE Appliances Answer Center® 1-800-626-2005. Monday-Friday: 8 a.m.-7 p.m. ET. ... Best to you and Good Luck.

If you have already replaced the Hi-Amp Door Switch on your GE Range Oven (Model: PS968SP1SS), but the oven light still will not turn off, there are a few additional steps you can take to troubleshoot the issue:

1. Check the light switch: Ensure that the light switch is functioning properly. It is usually located near the oven door frame or control panel. Press the switch manually to see if the light turns on and off. If it is not working, you may need to replace the light switch.
2. Inspect the light socket: Examine the light socket for any signs of damage or corrosion. If the socket appears to be damaged, you may need to replace it.
3. Verify the wiring connections: Check the wiring connections between the light socket, the Hi-Amp Door Switch, and the main control board. Ensure that all connections are secure and properly connected. Loose or faulty wiring can cause the light to stay on.
4. Test the main control board: As you suspect, a faulty main control board could also be the cause of the issue. You can try resetting the control board by turning off the power to the oven at the circuit breaker for a few minutes and then turning it back on. If the light still does not turn off, it may indicate a problem with the control board that requires replacement.

If you have performed these troubleshooting steps and the light still won't turn off, it would be advisable to contact GE customer support or a qualified technician for further assistance. They will be able to diagnose the problem more accurately and recommend the appropriate solution.