20 Most Recent GE JTP20 Electric Single Oven - Page 5 Questions & Answers


F2 means your oven is sensing that it’s too hot. Try cutting electrical power to it for 5 minutes. If that doesn’t resolve it, either oven temperature sensor / probe or control board will need replacing

GE Ovens | Answered on Nov 22, 2018


I just need the dimensions of jkp62g0k3 to replace with new onw

GE Ovens | Answered on Nov 02, 2018


Generally speaking, F2 fault code indicates the oven exceeded 590 degrees with the door unlocked. This could be caused by a stuck relay on the oven control board or it could be caused by high resistance in the oven temperature sensor probe.

If the element will shut off then the likely failure is the oven temperature sensor probe. The sensor is located inside the oven cavity. It will be protruding from the rear panel in the upper left or upper right corner. The sensor can be removed and replaced from inside the oven cavity

GE Ovens | Answered on Oct 30, 2018


An F9 error code on a General Electric (GE) oven indicates that the oven's electronic control system has detected a problem with the automatic door lock. The automatic door lock mechanism prevents the oven door from being opened when the oven is set for "Clean" mode. The malfunction may be a jammed door lock mechanism, a pinched or broken wire, a faulty lock switch or a fault in the control board itself

GE Ovens | Answered on Oct 21, 2018


this error for GE means that your touch control panel has shorted and the entire touch control panel would need to be ordered and replaced if resetting the circuit breaker won't reset the issue.

GE Ovens | Answered on Oct 13, 2018


Unfortunately, the error codes for appliances don't tell you the exact problem. F97 indicates a problem with the lower cooling fan that could be from the fan motor, the wiring, or the thermal switch that determines when the fan should come on or turn off. Make sure that the blades on the new fan rotate smoothly. That will rule out a bad replacement part. After that, you need to check the wiring harness. Make sure that there are no broken wires - check for continuity or missing insulation. You'll have to take the harness off both the connection at the fan and where it connects to the control board. Replace damaged wiring. Finally, you need to check the resistance across the switch and wiring to the switch. If the switch is bad, then you need to replace it.

I hope this helps.

Cindy Wells

GE Ovens | Answered on Oct 02, 2018


actually it takes less time to heat up and cook with the fan running
That is why it is called a fan forced oven as the fan forces the hot air all around the oven , heating it quicker and giving a better cooking result by moving hot air all around what is being cooked

GE Ovens | Answered on Sep 17, 2018


F2 means it thinks the oven temperature is over 900 degrees with the door locked. You can try to cycle the power to the oven to clear the code. If that doesn't work then it could be the temperate sensor, or the relays bad or shorted out. Here is a amazon link for a relay that should look similar to what you have depending on your model #.
Amazon com GE WB18T10352 Relay Home Improvement

GE Ovens | Answered on Aug 26, 2018


Hello,
You should replace the door lock mechanism and the door switch.

Global Solutions Appliance Repair
https://gsappliancerepairnyc.com/

GE Ovens | Answered on Aug 07, 2018


First, I'm not a GE tech.
* Check your warranty. Call for service.
*** The following is for information only ***
* GE Self Cleaning Oven instructions (a bit fuzzy); https://www.youtube.com/watch?v=2_hO7R29E9Y
* Updated video (steam clean version); https://www.youtube.com/watch?v=yg3EBU99PSE
* Older models (my mom's stove 1970's); https://www.youtube.com/watch?v=uBQa_yIyfgI
* Be safe contact GE for specific questions.; http://www.geappliances.com/

Aloha, ukeboy57


GE Ovens | Answered on Jul 07, 2018


Unfortunately, the F91 error indicates that the door lock is not functioning or the signal that the door is locked didn't get to the control unit. The range will not begin the self-clean cycle if there is a chance that you could open the oven door when the oven is dangerously hot.

First try cycling the power by unplugging the range (or turning off the circuit breaker). Next check if the lock has engaged. If the lock doesn't engage, check if the mechanism is bent or binding. Next check the wiring to see there is damage that will prevent the communication between the control board or the door lock. Check for corrosion at the wiring harness connections.

If the error happened after doing a self-clean, I'd suspect the door lock hadn't released. That can be related to a damaged over-temperature sensor or the lock itself. If the range has been self-cleaned before, it's possible that the lock was broken after forcing the door to open after that self-clean cycle.

You may need to replace the lock, the wiring or the control board. Please add a comment with the model of your range for a parts diagram. If your range is under warranty, contact GE.

I hope this helps.

Cindy Wells

GE Ovens | Answered on Jun 26, 2018

Not finding what you are looking for?
GE JTP20 Electric Single Oven Logo

61 questions posted

Ask a Question

Usually answered in minutes!

Top GE Ovens Experts

Michael Thomas
Michael Thomas

Level 3 Expert

3056 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

Cindy Wells

Level 3 Expert

6220 Answers

Are you a GE Oven Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

GE Ovens

  • GE Ovens

Most Popular Question

ge monogram 30 built in oven turns

  • Ovens
Loading...