20 Most Recent GE JTP20 Electric Single Oven - Page 2 Questions & Answers


Try turning the breaker to that unit off and keep it off for 20 minutes or overnight, if possible, then flip the breaker back on. If it still shows the PF code, call us and we can get the correct part to you. Hope this helps.

GE JTP20... | Answered on Aug 28, 2009


I have a GE JT950 double oven that just did the same thing: F7 and beeps like crazy. I found solution on another post: an engineer figured out how to solve the issue without calling GE or buying parts. I just did it tonight and it worked fine. Here is a copy of the post:

Send an e-mail to Charlie at [email protected] for a fix-it that you can try. He explains a possible solution fully with his 'The Dreaded "F7" Error' solution. I actually found his information on another website when I did a web search for "GE Profile Oven F7 Issue". I sent an e-mail to him and he replied with free fix-it information. I am not a repair person myself, but, his instructions are very clear and simple to follow. I did the fix-it at no cost in approximately 10 minutes and it has solved my problem

GE JTP20... | Answered on Aug 01, 2009


HI, this is a lock switch mechanism failure.


Check wiring to door lock switch (the wire harness may be connected wrong). Check for stuck lock switch.

If the wiring is connected properly, simply replace the door lock switch.

***(It is possible that is is stuck. trying correcting this before purchasing a new switch)---(Highly uncommon)


GE JTP20... | Answered on Jul 15, 2009


Open or shorted oven temperature sensor (RTD)

Check sensor harness and harness connection between oven sensor and oven control. Replace oven temperature sensor (RTD) if wiring is ok.

GE JTP20... | Answered on Jun 25, 2009


This is a shorted touch pad. replace the touch pad or, if the touch pad is incorporated within the control board, replace the entire oven control board.

GE JTP20... | Answered on Jun 25, 2009


Not sure if this link will work, but give this a try
http://claimworks.servicepower.com/mfgltr/I404/RC/Wall%20Oven%20Repair%2011-4.pdf

There is a recall on the oven door for a few models
Safety Recall GE Wall Oven Models Included in the Recall
Brand Model Numbers Must Begin With Serial Numbers Must Begin With GE® and GE Profile™ JCT915, JT912, JT915, JT952, JT955, JT965, JT980*, JTP20, JTP25, JTP28, JTP48, JTP50, JTP86 TD, VD, ZD, AF, DF, FF, GF, HF, LF, MF, RF, SF, TF, VF, ZF GE Monogram® ZET3058, ZET938, ZET958 TD, VD, ZD, AF, DF, FF, GF, HF, LF, MF, RF, SF, TF, VF, ZF Kenmore
(All model numbers start with 911) 4771, 4775, 4781, 4904, 4905, 4923*

* Lower Oven Only 2T, 2V, 2Z, 3A, 3D, 3F, 3G, 3H, 3L, 3M, 3R, 3S, 3T, 3V, 3Z
and that link shows the door and hinge. Recall info at
http://www.geappliances.com/products/recall/wall_oven_08/

GE JTP20... | Answered on May 31, 2009


REPLACE THERMOSTAT AND TEMPERTURE PROBE

GE JTP20... | Answered on Apr 29, 2009


Its possible that the wiring harness to the door switch got a little too hot and have shorted. What I would do before I call a technician is to unplug the oven or turn the power off to it for a few minutes and then plug it back in to reset the control board. If you still get the error, I would recommend calling a service professional.

GE JTP20... | Answered on Apr 03, 2009


From all the information I could gather on this issue, including speaking with a GE tech I decided to call in a repair person.

GE JTP20... | Answered on Feb 27, 2009


get a multimeter and test the resistance of the element and ohms, be sure to turn off the power first, take the element loose, and ohm it out, and check the resistance of the element. Most multimeters have a continuity setting, and try that and see if the element has continuity. if it doesnt, chances are that that is your bad element

GE JTP20... | Answered on Jan 23, 2009


The F2 typically means an overtemperature conditions:
1. over 650 degrees F unlatched or 915 degrees F latched.
2. cooling fan stalled while over above 650 degrees F or an oper thermal switch in the yellow leads.
Check for:
1.Welded relay contacts
2.Cooling fan stalled or blocked air flow to rear of unit.
3.High resitance in over sensor leads/connectors, especially at sensor in rear.

GE JTP20... | Answered on Dec 30, 2008


You can go to http://www3.sears.com/ or http://www.appliancepartspros.com/. You will need the complete model # from the sticker on the oven. The # listed above is not correct. It looks like a serial #.

GE JTP20... | Answered on Nov 07, 2007


The hinges are obstructed or the springs have been weakened by heat. Correction of the problem requires removal of he oven and disassembly to gain access to the affected parts. Not an easy job because those parts are enclosed in the outer shell of the oven.

GE Ovens | Answered on Jan 02, 2021


Check that whatever switches the light on and off is making good contact. My GE fridge has a bottle cap glued to the inside of the door, crude but it works. Some are magnetically operated, so you could test with a rare earth magnet.

For a mere $73 you can purchase a new switch.

ZET1PH1SS - Appliance Parts HQ

www.appliancepartshq.ca > lookup
Search by Keyword(s):. Diagram for ZET1PH1SS ... 55, WG02L07803, Badge Monogram Small No Pin, $150.44 ... 132, WG02L03187, G.e. Range Door Gasket, $84.82 ... 608, WG03F03565, G.e. Refrigerator Freezer Light Switch, $73.40

GE Ovens | Answered on Dec 19, 2020


Try checking on Ebay. I seen this one, but i can't answer if it a good match (if it looks close you may be able to patch it in).
https://www.ebay.com/itm/284067140396

GE Ovens | Answered on Dec 08, 2020


The F7 error indicates a stuck keypad error on GE ovens. This actually could be a stuck or shorted key, a problem with the ribbon cable between the keypad and the control board, or a problem with the electronic oven control. On a number of GE ovens, the issue is with the ribbon cable. There could be insufficient insulation shielding the individual conductors in the wiring harness, a broken conductor (single wire) or corrosion at the connection to the control board. Sometimes the keypad or the control board need to be replaced. Make sure to disconnect the power (unplug or turn off at the circuit breaker) before attempting to do any diagnostics.

Some parts for the JKP27WOW2WW are available here: https://www.appliancepartspros.com/search.aspx?model=jkp27w0w2ww . I hope this helps.

Cindy Wells

GE Ovens | Answered on Nov 25, 2020

Not finding what you are looking for?
GE JTP20 Electric Single Oven Logo

61 questions posted

Ask a Question

Usually answered in minutes!

Top GE Ovens Experts

Michael Thomas
Michael Thomas

Level 3 Expert

3056 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

Cindy Wells

Level 3 Expert

6220 Answers

Are you a GE Oven Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

GE Ovens

  • GE Ovens

Most Popular Question

ge monogram 30 built in oven turns

  • Ovens
Loading...