Kenwood KM800 Major Classic Stand Mixer - Answered Questions & Fixed issues

Fixya is unable to suggest Kenwood parts sources.

Kenwood KM800... | Answered on Mar 04, 2018 | 286 views

I'm not 100% sure exactly what you're looking for but these folks have all sorts of parts lids/covers.
hope this helps you.

Kenwood KM800... | Answered on Feb 26, 2018 | 345 views

sounds like aproblem with the brushes are worn out or damaged armature if you contiue to use it before you check the brushes you will permetly damage it

Kenwood KM800... | Answered on May 15, 2015 | 562 views

Welcome to Boelter

MilwaukeeRestaurant Equipment Repair Service


Kenwood KM800... | Answered on Feb 02, 2015 | 216 views

In my case, capacitor C1: 470nF (on the circuit board) proved to be the cause. It measured only half its normal value. It's part of a voltage divider used in place of a transformer. Replacing it solved the problem.
Came already across the same problem in another circuit.

Kenwood KM800... | Answered on Jul 25, 2014 | 512 views

Could you send me a service manual for an a901 please? Just inherited one from my nan, and serviced it but stupidly cant remember which order the lower bearings go on the motor :/
[email protected]

Kenwood KM800... | Answered on Jun 09, 2013 | 3,519 views

how to remove the shaft,1/2 sheered into the can i remove [email protected]

Kenwood KM800... | Answered on Jan 26, 2013 | 245 views

whats the problem with the mixer?

Kenwood KM800... | Answered on Jan 10, 2013 | 304 views

I have just had the exact sme problem.
It is caused by a 1 watt resistor on the board.
You will also find that very possibly the large capacitor, a 0.1uF, has aso burnt out. This capacitor would have cracked open down the side and that is where the smoke came from.
parts can be replaced by a repair man and possibly a better solution is to have the board replaced, They are availiable still.

Kenwood KM800... | Answered on Oct 24, 2012 | 4,320 views

What resistors and capicitors are used on the motor control board on the Kenwood A901.
Thank you

Kenwood KM800... | Answered on Feb 02, 2012 | 921 views

My chef A901 started to smell and leak oil. I started to dismantle it but found that a service manual is needed. Kenwood will not supply this for "Health an safety" reasons. can anyone help please.

Kenwood KM800... | Answered on Feb 23, 2012 | 545 views

You can buy genuine spare parts for most models of kenwood chef at

Kenwood KM800... | Answered on Jan 06, 2012 | 81 views

Hi Emma,
Not going to be much help here to be honest. We have the KM020 and this is the only problem we have had with heavy machine use in 4 years - and a minor issue at that.
This place is good for spare parts

If you're in the UK, you can call this number 02392 392 333 and give them your post code, they'll let you know who the local service agent is.
All the best,

Kenwood KM800... | Answered on Dec 17, 2011 | 302 views

Force it out carefully. One person wrap tea towel over hook and turn forcefully, anticlockwise. Secnd person use a long handle screwdriver to hold the Kenwood still - wedge between the housing where the hook inserts. Hold Kenwood still whilst twisting the hook. When it comes apart, clean 'hole' and hook shaft thoroughly with WD40 / oil. Might need new hook if too damaged. Ours is ok seemingly.

Kenwood KM800... | Answered on Dec 02, 2011 | 397 views

Not finding what you are looking for?
Kenwood KM800 Major Classic Stand Mixer Logo

220 questions posted

Ask a Question

Usually answered in minutes!

Top Kenwood Food Mixers Experts


Level 3 Expert

85239 Answers

Lawrence Oravetz

Level 3 Expert

10548 Answers

Ross Keen

Level 3 Expert

1364 Answers

Are you a Kenwood Food Mixer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides