20 Most Recent Kenwood Radio TK 260 360 270 370 2100 3100 Compatible Battery Questions & Answers

0helpful
1answer

Looking for a program and cable for a Kenwood TK 2212-1 handheld

Software TK-2212 is KPG-100 and normal kenwood cable KPG-22 can be used for programming.
4/25/2019 10:32:45 AM • Kenwood Radio TK... • Answered on Apr 25, 2019
0helpful
1answer

Can't read or write Kenwood TK-7302 radio blocked by passwords

Change the EEPROM or contact Kenwood Customer Care, they will send you software by which you can read/write the Radio.
4/25/2019 10:00:06 AM • Kenwood Radio TK... • Answered on Apr 25, 2019
0helpful
1answer

I was trying to add

First you connect your radio with pc and try to read your radio, if it read then you rewrite it, if you sucessful, it ok, other wise your radio have a hard ware problem because cpu not communicate the eeprom and ram.
4/25/2019 5:57:50 AM • Kenwood Radio TK... • Answered on Apr 25, 2019
0helpful
2answers

Can't transmit signal. Only get a 2 second beep when I push the transmit button

You have a poorly charged or bad battery. It takes more power to transmit than to receive. Usually the first thing you lose with a low, bad or poorly charged battery is transmit. Try a known good battery in the radio. This should solve the problem. If not, check your battery contacts, as you may have one which is bad or not making good contact. Clean your contacts with a pencil eraser to assure good connection with the charger. Best regards.
10/28/2014 12:13:26 PM • Kenwood Radio TK... • Answered on Oct 28, 2014
0helpful
1answer

I NEED WIRING GUIDE FOR a PPT, PRC to Kenwood K1

not sure does this help? http://images.kenwood.eu/files/prod/855/5/R-K1_EN.pdf
5/8/2014 10:39:26 PM • Kenwood Radio TK... • Answered on May 08, 2014
0helpful
1answer

Looking for a link to download programming for my tk7160

You may find it on the Kenwood commercial radio web site, but you'll need a programming cable also.
11/7/2013 4:22:48 AM • Kenwood Radio TK... • Answered on Nov 07, 2013
0helpful
1answer

Hi.. i have talkie tk-3000, buy from dealer.. but

Re program radio but you cant do a backup I don't think Re: Jeff
11/4/2013 8:49:37 AM • Kenwood Radio TK... • Answered on Nov 04, 2013
0helpful
1answer

When I key the mike, the radio powers-off and

The battery is too low to support TX. Probably need to replace it.
10/30/2013 4:47:19 AM • Kenwood Radio TK... • Answered on Oct 30, 2013
0helpful
1answer

How do you perform a

Field Programming procedure for the Kenwood TK-270 or TK-370 handhelds. Press and hold (light) & (dial) while turning on radio. Hold until (SEL) appears on the display. Pressing (SCN) allows you to program the following 1. Monitor Key Off = off 1 = Monitor momentary 2 = Monitor Lock 3 = Squelch off momentary 2. Scan Key Off = off Co = carrier operate To = Time operate 3. Dial Key Off = off On = enable 4. TA key TA = talkaround RV = Reverse Off 5. Lo Key On Off 6. Priority None 1 = fixed 2 = selected 7. Fixed Priority Channel Turn selector to channel 8. Look back time A Turn selector to time in seconds 9. Look back time B Turn selector to time in seconds 10. Revert Channel 1 = Selected 2 = Last Call 3 = Last used 4 = Selected + Talkback 5 = Priority 6 = Priority + Talkback 11. Tx Dwell time Turn selector to time in seconds 12. Drop out delay Turn selector to time in seconds 13. Time out timer Turn selector to time in seconds 14. Tot Pre-alert Turn selector to time in seconds 15. Tot Rekey time Turn selector to time in seconds 16. Tot reset time Turn selector to time in seconds 17. Squelch Level Turn selector to Squelch 18. Beep tone On Off 19. Signalling And Or 20. Battery Save On Off 21. Selectable QT On Off 22. Clr to transpond On Off 23. Del/ Add On Off Pressing (Dial) allows programming of: DTMF 24. digit time Turn selector to time in milliseconds 25. inter digit time Turn selector to time in milliseconds 26. First digit time Turn selector to time in milliseconds 27. Rise time Turn selector to time in milliseconds 28. Rise time with QT Turn selector to time in milliseconds 29. PTT ID Off 1 = connect 2 = disconnect 3 = Both 30. Dial ID On Off 31. Connect ID 32. Disconnect ID 33. # of DTMF keys on Keypad 12 16 34. DTMF hold time On Off 35. Store & send On Off 36. D key assignment Turn selector to D or time in seconds for pause 37. Dtmf Signaling Off 1 = code squelch 2 = Selective Call 38. Intermediate Code OFF A B C D E F 39. Group Code OFF A B C D E F 40. Auto Reset time Turn selector for time in Seconds 41. Call Alert/ Transpond Off 1 = 2 = 3 4 5 42. Transpond On Off Pressing (TA) will allow you to program Frequencies Use selector to choose channel Press PTT Enter Rx frequency using: - the Selector Knob to change kHz; - the Selector Knob + (light) to change MHz. If no channel is Shown press the (LO) button. Press PTT Enter Rx CTCSS code Press PTT Enter Tx Frequency as above Press PTT Enter Tx CTCSS code Press PTT 1. Option Signal Off 1 = DTMF 2 = 2-Tone 2. PTT ID On Off 3. Add/ Del 4. Busy Tx 5. Clock frequency shift 6. Power Hi Low Repeat for the other channels (you've got a 32 channel radio, so it may take a while...) <end>
10/30/2013 4:45:23 AM • Kenwood Radio TK... • Answered on Oct 30, 2013
0helpful
1answer

Change from wide band to nerrow band

You'll need a programming cable and the software for the radio.
10/30/2013 4:38:38 AM • Kenwood Radio TK... • Answered on Oct 30, 2013
0helpful
1answer

Can i field program a

If you buy a programming cable and the software, yes. Unless you're a certified technician (or you're an Amateur using it in the Ham Bands) programming a commercial radio is illegal.
10/30/2013 4:36:41 AM • Kenwood Radio TK... • Answered on Oct 30, 2013
0helpful
1answer

The battery on my tk 360 keeps dislodging

Hi Mike,Yes it's a pain in the rear when you have this happen, I have a Vertex that had the same issue, this is how I solved it.Get yourself a piece of wide elastic, enough to go around the radio and battery to hold it tightly, A wide rubber band could be used, but they wear out too quickly for my liking, another item to get is the leather portable radio holster, for when you're mobile and an extension mic, this is the best solution for mobile radios when your out doors anyway.I hope this has been useful to you. The problem is the locking mechanism between battery and radio.Cheers,Peter
3/11/2013 11:37:32 AM • Kenwood Radio TK... • Answered on Mar 11, 2013
0helpful
1answer

I have a Kenwood TK 270G and it will no longer scan. when you push scan it says"locked" my young kids got it so i dont think its broken

Hi,You've probably answered your own query in part there.To help you get back into buisness, do the following:Join yahoo group specific to your radio Make/Model, the people there specialise in just that model, so give them as much info as you can think of, the more info you give, the quicker a solution to your problem, and don't be shy about asking as many questions as you feel necessary, the more info the get the more answers you get. All this is FREE, and you can download manuals, schematics and other goodies for your radio.I hope I've helped to get a solution.Best regards,Peter
3/6/2013 6:14:18 AM • Kenwood Radio TK... • Answered on Mar 06, 2013
0helpful
2answers

My new used kenwood tk370

If you have not resolved this problem yet. I fear that your radios may have a CPU problem. in any case here is a URL that explains how to program your radios. http://www.repeater-builder.com/kenwood/field-programming-tk-x70.html

Pat N5SLI
9/8/2012 2:07:24 AM • Kenwood Radio TK... • Answered on Sep 08, 2012
0helpful
2answers

Programming Software for Kenwood TK-3130 Protalk XLS Radio

The software is only availible from Kenwood. the only way to get it is to purchase the registration key from them for that software. Sorry, I program radios everyday and even the company I work for has to purchase the Registration keys.
7/12/2011 11:09:34 PM • Kenwood Radio TK... • Answered on Jul 12, 2011
0helpful
1answer

I have a tk-390 portable radio and it continues to

I am having the same problem. Does anyone out there have a solution?
12/7/2010 5:56:09 PM • Kenwood Radio TK... • Answered on Dec 07, 2010
0helpful
2answers

I have a kenwood tk260.

have you tried "rebooting" it. basically taking out the battery for about 15 minutes to a half hour. ?
8/22/2010 5:10:07 PM • Kenwood Radio TK... • Answered on Aug 22, 2010
Not finding what you are looking for?
Kenwood Radio TK 260 360 270 370 2100 3100 Compatible Battery Logo

64 questions posted

Ask a Question

Usually answered in minutes!

Top Kenwood Radio Communications Experts

eradiostore
eradiostore

Level 3 Expert

1670 Answers

Jaime Hernandez

Level 3 Expert

2351 Answers

Steve

Level 3 Expert

3290 Answers

Are you a Kenwood Radio Communication Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Kenwood Radio Communications

  • Kenwood Radio Communications

Most Popular Question

perform

  • Radio Communications
Loading...