Top 20
Lanier 1205 Copier - Page 6 Questions & Answers
Lanier LD032
Hi Dwayne:This error occurs when performing the white level detection. Check: a - The white board on whether or not this position b - Glass and Optical c - UBS Card - (card may be faulty) d - BICU Card (may be faulty) e - Check the optics and connectors to the cards. I have heard that several times after cleaning the mirrors of the scanner worked.Hope this helps; also keep in mind that your feedback is important and I'll appreciate
your time and consideration if you leave some testimonial comment about
this answer.Thank you for using Fixya, and have a nice day.
Service code
Welcome to Fixya
Try to reset the system back to the factory state. Here's the procedure:
System Setting Reset
The system settings in the UP mode can be reset to their defaults. Use the following procedure.
1. Press User Tools/Counter .
2. Hold down the '#' key and then press System Settings.
3. Press yes when the message prompts you to confirm that you want to reset the system settings.
4. Press exit when the message tells you that the settings have been reset.
Thank you for using Fixya! If you need further help, reach me via phone at
https://www.6ya.com/expert/elixirjose_00375ea24bd8141b
My copier ran out of toner, I replaced it with a
There may be a clog in the toner supply unit, if you have a small vacuum made for copiers vacuum the toner supply unit and see if it corrects the problem if not you may need a new toner supply unit. Hope this helps
Service code sc523 , copier wont work
Ok. Try this procedure:
Press yellow key.
Press 107 on the key pad
Press red key at least 5 sec.
Press "copy SP"
Press 5810 on the key pad and press #
Press "execute"
Exit all the way out and turn the machine OFF and ON.
If this do not work i advise you to call a technician to see whats going on with the Fuser Unit.
It could be a faulty Thermistor...
In Lanier GX3000 I would
The printer requires that all of its ink cartridges have ink before printing, the color ink cartridges will have to be replaced.
I have a Lanier 116cn
The
machine have problem with the transfer roller or the motor which drives
the transfer is overloaded,
see do the right door is closed good
if
this not helped it will need to be checked by a technician.
Lanier model 5627 with fault code sc542 upon power
LOL I think I already gave you a solution
try this:
1. Press the clear mode key (yellow key)
2. Use the keypad to enter "107"
3. Old down clear/stop for at least 3 secunds. (red key)
4. Enter the service mode.
5. Exit all the way and turn off.
6. Turn ON
And thats it
I have a lanier ld122 copier/fax. It told me to
First of all check if the doors are well closed.
If everything is well closed you can have several problems:
1º Toner supply defective.
2º TD sensor defective
3º Development unit defective.
If you don't have technical training i advise you to call the provider.
We have a dark vertical
It appened when you take a copy????? If so, you probably hava scanner mirror durty.
Lift up de feeder end you see five screws.
Unscrew them and you have access to the mirrors.
Just wipe gently to avoid moving the mirrors
When we try to copy
Hi shiana,
On the right side of your copier is a "box" called the duplex unit.It really is a silly *** box LOL.Now....either it is not firmly latched to the copier .......OR....the metal tab on the main copier is bent so that even if you put the duplex unit firmly in place ........the little switch on the duplex unit is still not :satisfied: And we hate that. I bet ya got it fixed in a jif. take care :-)
Lanier 5518 gives a SC320
This SC-320 code error occurs when polygon mirror motor fails or poor connection between BICU & polygon mirror motor please check first the connector of motor if you feel that the connector is good change the polygon mirroe motor it sits inside the LD unit please call the expert to change the part
thanks
We have a Lanier 5618
first you have to see if it happens when they get to a copy or a print. If it happens in print there is not much to clean, you have to replace worn parts. If it happens only on the copy you have mirrors Sanner dirty. (strip the screws and lifting the glass carefully cleaned the mirrors).
Hope this has helped
Paper is solid black when trying to copy
make sure the top lamp lights when you press the print key if the lamp does not come on check the lamp harnes, the fuse, the lamp and the exposure board replace if either is faulty
LANIER 5637 FAULT CODE SC542 UPON POWER UP
You have a Fuser Temperature warm-up error, Hot roller warm-up error.
Verify the heater lamps, thermistor and thermofuse continuity.
Enter in the SP mode, turn OFF the main switch, unplug the machine, wait 10 seconds,
plug in and turn ON the copier.
If you need to reset the fuser, Enter SP 5-810 (SC code reset) and
select "1". Then simultaneously press the Original Type key and the OK (or
R/#) key. (There is no need to turn the main switch off and on.).
We have a lanier 5216
Hi,
System Setting Reset
The system settings in the UP mode can be reset to theirdefaults. Use the following procedure.
1. Press User Tools/Counter .
2. Hold down the '#' key and then press System Settings.
3. Press yes when the message prompts you to confirm thatyou want to reset the system settings.
4.Press exit when the message tells you that the settings have been reset.Please do rate the solution if the issue is resolved or post a comment for further assistance.
Thank you for using fixya have a nice day:-)
Not finding what you are looking for?