Olevia 227-S11 27 in. LCD TV - Answered Questions & Fixed issues

Set-up (Programming) procedure is too much to type in here, and is not practical and it will differ brand-to-brand remote controls. If you wish to get more; check the sites linked here. It has set-up code list & set-up procedure to many popular brand remote controls. One among it has general set-up codes to check with TVs and other devices are given, in the order of the 'device's brand name list' in alphabetical order. Pull up older posts. Search the sites by type in the brand name to your device in its search box at the top right part of the display window. It will help you to find the document easily. http://electro-medical.blogspot.com/

Easiest place to start is the cables and connections. You should be able to get a reaction from the monitor by jiggling them. If you do see the problem go in and out by doing this then replace the cable. If not the cable then you are looking at the video board.

Fault with the main power supply regulator board. Check and replace damaged component/s at its main power regulator [SMPS] section circuit. Contact any service technician. If you wish to get some details; check the site linked here. Surf the site with patience. Pull up older posts. http://electronicshelponline.blogspot.com/ It will be best to replace the power supply regulator board as card basis rather than making "Surgery" to it; which usually will make loss for both money and time.

Check its input connection for any loose contact. Make sure that the external antena has been connected to the proper input socket to the TV. If all are found OK, the tuner to your set is faulty. Contact any service technician. If you wish to get some details; check the site linked here. Pull up older posts. Surf the site with patience. http://electronicshelponline.blogspot.com/

Main broad fault. Contact the authorized service center. Electro help

T'Con board fault. Contact any service technician. If you wish to get some details; check the site linked here. Viewing it in "Mosaic" or "Magazine" will make surf easy. Pull up older posts. Surf the site with patience. Do a search by type in the brand name of your device at its search box and press "Enter". http://electronicshelponline.blogspot.com/

There is no such facilty to any TVs. When you plug in the head-phone pin into head-phone socket, the internal speakers will cut off, and audio will be only via headphones, and vice versa.

You may use a wireless system. WalMart has wireless sets from $18 and up. Naturally the higher the price the better the quality. If you are near a RadioShack they too, have a variety to select from. They use Recahrgable baterys.

the Inverter would be suspect if the audio works but no picture with black screen

The problem post of yours' is very difficult to understand. Please provide more details.

Contact the nearest authorized service center for Olevia to buy a new original remote control.

Can you please go through guidelines in the operation manual, especially what system/format is supported in HD input?

You may have to guidelines given in the operation manual step by step and try resetting, if necessary. Also check whether the system/format transmitted through cable is supported by our TV.

From AT&T?

Check these codes: 11144, 11240, 11331programmmming TVTV controlThe Comcast DTA remote control is preprogrammed at the factory to operate the DTA receiver. The Comcast DTA remote also contains a universal TV library to allow you to control the Power and Volume of your TV.1. Turn on the TVNOTE: Please read steps 2 to 4 completely before proceeding. Highlight or write down the codes and device you wish to program before moving on to step 2.2. Press and hold Setup until the Red Light blinks twice, then release Setup.3. Locate the code for your device in Manufacturer's Codes on the back of this user guide. Brands are listed in alphabetical order with the most popular codes listed first.4. Enter the first five-digit code for your TV. If you perform this procedure correctly, the Red Light will blink twiceNOTE: If you enter an invalid code, the red light will display one long blink and exit the programming mode. Repeat steps 2 to 5 with a valid code.5. Aim the remote control at your TV and press Power once. The device should turn off. If it does not respond, repeat steps 2 to 4, trying each code listed for your brand until you find one that works. If it still does not work, try Searching For Your Code.

thats almost always going to be a power supply issue, You should be able to get a replacement power supply from www.tvrepairworld.com they have many which arent listed so calling them is the best bet if you dont see your board listed.

restore tv

I see so many here with no sound/nopicture issues:ISSUES: 1. IF sound main fuse/s are good.2. If no power or standby check main fuse, standby power supply and any signsof damage you can see---burnt parts etc.3. almost all these sets the troubleshooting involves checking voltages on the main power board to narrow down theproblem.4. Be safe and if you do not know what you are doing don't open the set.Answers to issues:1. RE:fuses---if a blown fuse is found get a good replacement(not the genericones like Radio Shack). Many fuses are special even aside from amperage--Don'tput a higher rated amperage fuse in the set for any reason.2. RE: power supply in set: if total dead aside from main fuse the set uses astandby power supply that runs 7/24 and a main supply (some are combined andsome not.Here aside from checking fuses you want to examine all the filter caps on thepower/standby to see if any are puffed up or buldged up in some fashion--Iattach a photo of a good one---top should be silver metal and PERFECTLY flatand have no brown material coming out on top or bottom.What happens in the standby area is they use caps with too low a voltage rating(saves money) which causes them to fail in a year or two---the standby runs7/24 and the heat dries out the caps and they fail.3. Trouble shooting consists of the above and then at some point you have to buyand try a board to see if it fixes it or not.4. Safety first--no TV set is worth getting injured or even killed over.If set is opened at least look for puffed up and bad caps like in thisphoto.

Go to the menu and then enter your choice out of them like find channels or scan/scan channels.

The fuse is located on the power supply. You have to remove the back cover of the LCD in order to get to the power supply. The fuse should be near the AC power cord jack. If the fuse is blown, you may have bigger problems than you anticipated.