20 Most Recent Samsung PS50Q91HD 50 in. HD-Ready Plasma TV - Page 8 Questions & Answers

The issue with your Samsung Solar Remote not syncing with the TV even though the Bluetooth icon is appearing on the TV could be caused by a few different things. Here are some troubleshooting steps you can try to resolve the issue:

1. Check the battery: Make sure that the battery of the remote is charged and inserted correctly.
2. Move the remote closer to the TV: The remote should be within 30 feet of the TV to ensure a strong Bluetooth connection.
3. Turn the TV off and on again: This can help to reset the Bluetooth connection between the remote and the TV.
4. Remove the pairing information: If you have paired the remote with another device before, it may have saved the pairing information and is interfering with the new pairing. Try removing the pairing information from the remote and the TV and then pair them again.
5. Reset the remote: You can reset the remote by removing the battery, then pressing and holding the power button for 10 seconds, and then releasing it. Reinsert the battery and try to sync the remote again.

If these steps don't resolve the issue, try contacting Samsung support for further assistance.

Determining the cause of a blown fuse can be a difficult task and requires a certain level of expertise and knowledge of electronic systems. If you have experience with control boards, that's great, but it's still important to exercise caution when working with electrical systems. Here are some steps you can take to determine the cause of the blown fuse:

1. Check for obvious physical damage: Before you begin, inspect the television for any physical damage or signs of burn marks. If you find any, it could indicate that there is a problem with the TV's power supply.
2. Check the wiring: Make sure that all the wiring is properly connected and that there are no loose or frayed wires.
3. Test the power source: Make sure that the electrical outlet is working properly by testing it with a different device.
4. Check the capacitors: Capacitors are often the cause of blown fuses. They can fail due to overheating or other reasons. You can visually inspect the capacitors to see if they are bulging or leaking.
5. Isolate the problem: Disconnect the TV from the power source and unplug it from the wall. Then, one by one, reconnect each board to the power source and see which one is causing the fuse to blow.

If you're not comfortable working with electrical systems, it might be best to call a professional for help. If the problem is a blown fuse, replacing it will be relatively easy, but if the problem is more complicated, such as a faulty power supply, it may require more time and expertise to resolve.

I know this is from a few months ago.... but I just had the exact same thing happen to my Samsung UN70NU6900F. After doing some research and taking the back off I've come to believe it's the cable ribbon! I've managed to get my picture to come back on multiple times, so I'm gonna order a new ribbon and hope that's the case ??

Newer Samsung sets don't use screws for the back or to hold the boards in, you will see slides on the top of the board, pull up on the board( lightly) and slide the board out.

Most likely but look at the part numbers on each board to see if they're the same.

If you have replaced the main board and power supply board and are still getting a uniform blue screen on your Samsung LED TV, it could indicate one of the following issues:

1. T-Con Board: The T-Con board, or Timing Control Board, is responsible for managing the flow of video data from the main board to the LCD panel. If the T-Con board is damaged or not functioning properly, it can result in a blue screen.
2. Backlight Inverter: The backlight inverter is responsible for powering the backlight of the TV. If the backlight inverter is not working properly, it can result in a uniform blue screen.
3. LCD Panel: The LCD panel could be damaged or have developed a problem, causing the uniform blue screen.
4. Signal Cable: The cable connecting the main board to the T-Con board or the LCD panel could be damaged, causing a lack of signal and a blue screen.

It's best to consult with a professional repair technician or the manufacturer for further diagnosis and repair. They will be able to determine the exact cause of the issue and recommend the best course of action.

La ligne bleue verticale et la ligne rouge horizontale sur votre t?l?viseur Samsung mod?le UN65RU8000FXZA peuvent indiquer un probl?me avec le mat?riel de l'?cran. Les options suivantes sont disponibles pour r?soudre ce probl?me :

1. V?rifiez les connexions : Assurez-vous que toutes les connexions de votre t?l?viseur et de vos appareils externes sont correctement connect?es et s?curis?es.
2. Mettre ? jour le firmware : Il est possible que votre t?l?viseur ait besoin d'une mise ? jour du logiciel. Consultez la section de mise ? jour du firmware sur le site web du support Samsung pour savoir comment mettre ? jour votre t?l?viseur.
3. R?initialiser le t?l?viseur : Essayez de r?initialiser votre t?l?viseur aux param?tres d'usine pour voir si cela r?sout le probl?me.
4. Contactez le support technique : Si les ?tapes ci-dessus ne r?solvent pas le probl?me, il peut ?tre n?cessaire de contacter le support technique de Samsung pour obtenir une assistance suppl?mentaire.

In order to use your old Samsung Dine DV3 TV, you will need to connect it to a source of video and audio. To do this, you will need the following cables/leads:

1. HDMI Cable: This will allow you to connect the TV to a modern HDMI-enabled device, such as a cable or satellite box, Blu-ray player, or gaming console.
2. RCA Cable: This will allow you to connect the TV to an older device, such as a VCR, DVD player, or game console, using composite (yellow, red, and white) connectors.
3. Coaxial Cable: This is the cable that will connect your TV to a cable or antenna source.

It's important to check the inputs available on the back of your TV to determine which cables you will need. The TV manual may also be helpful in identifying the required cables/leads. If the TV has a coaxial input, connecting to a cable or antenna source may resolve the issue of getting snow and BBC mono on the screen.

The back light is not working and there could also be a problem with the power board and the screen for your TV.

The issue you're experiencing with your Samsung UN50EH5300FXZA TV cycling on and off when you press the menu or source keys could be due to a hardware malfunction in either the main board or the power board. Here are some steps you can try to resolve the issue:

1. Power reset: Unplug the TV from the power source, wait for a minute, and then plug it back in.
2. Check the cables: Make sure all cables are securely connected to the TV and the wall outlet.
3. Check for firmware updates: Check if there are any firmware updates available for your TV and install them if necessary.
4. Factory reset: Perform a factory reset on the TV to erase all settings and return it to its original state.
5. Contact Samsung support: If the issue persists after trying these steps, contact Samsung support for further assistance. They may be able to diagnose and resolve the issue.

How to fix upside down TV screen Samsung TV

https://en.tab-tv.com > All Oct 10, 2022 - The first way to fix an upside-down 180-degree picture. It could be that the wrong display type is set in the settings. This is pretty easy to ...

. If the LEDs are not coming on, it is likely a problem with the power supply. You could try testing the power supply with a multimeter to see if it is providing the correct voltage to the LEDs. If the power supply is fine, then you may need to test the individual LEDs for any issues. Alternatively, you could replace the entire LED strip to see if that solves the problem

The manual for the Samsung BN59-00865A remote control can be found on Samsung's official website or by contacting Samsung customer support. Here's the link to download the manual: https://www.samsung.com/us/support/downloads/BN59-00865A The manual provides detailed information on the features, functions, and operation of the remote control, including how to program it to work with other devices and how to troubleshoot common issues.

It is possible that the issue is due to the connection between the Y-SUS board and the picture buffer. I suggest double-checking all the connections to ensure they are secure and working properly. Additionally, it may be worth cleaning the connections with a cloth or electrical contact cleaner to make sure the connection is clear. If the issue persists, then you may need to replace the Y-SUS board or get professional assistance.

I have the same issue, you've got to disassemble it and fix the connector that's on the front right side when looking straight down at the blu ray player, it's goes from the main board to the round selector on top that allows you to control the machine!

The Power board was the most likely, or an overheating issue, called power cycling. You should have connected your digital multimeter to the power board outputs and watched. This is the problems you face with home repair. https://www.fixya.com/support/r29790007-repairing_own_television ..

First thing to do is unhook the connector going from the main to power board, plug the set in and see if you get backlights, if you don't replace all the LED strips

Here are the general steps to program a BN59-00850A remote to pair with a Samsung DVD player:

1. Turn on the DVD player and make sure it is set to the correct input on your TV.
2. Locate the "Code Search" button on your BN59-00850A remote, this button is usually located at the top of the remote. Press and hold the "Code Search" button until the indicator light comes on.
3. Press the "DVD" button on the remote and release the "Code Search" button. The indicator light will flash to indicate that the remote is in programming mode.
4. Use the numerical buttons on the remote to enter the code for your Samsung DVD player. The code can be found in the remote control's user manual, or by contacting Samsung customer service.
5. Press the "Power" button on the remote. If the code is correct, the DVD player should turn off.
6. Press any button on the remote to exit programming mode.
7. Test the remote by pressing the "Power" button to turn on the DVD player and other buttons to ensure that they are working properly.

The BN59-00599A remote was included with several Samsung TV models, including the FP-T5084. While it can be used to control some other devices in your home theater system, it doesn't have codes for other TVs. See the user manual available at the support page: https://www.samsung.com/ca/support/model/FPT5084X/XAA/#downloadshttps://www.samsung.com/ca/support/model/FPT5084X/XAA/#downloads . The section on setting the remote for DVD players, VCRs and other devices starts on page 20. I wish that I had better news for you. To control the Bush TV, look for a generic universal remote that was programmed more than 6 months after the TV was manufactured. (Not all remotes will list codes for Bush TVs, however the code for another brand may work.) Cindy Wells

There is a good chance you have a bad panel, put the original boards back in the set, unhook the ribbon cables going to the panel boards from the main or tcon, I didn't pull service info so don't know if this set has a tcon board, in either case, remote the ribbon cables going to the panel boards , if the set comes on with backlights, naturally no picture, the panel is bad