Sunbeam SCA102RPC1 Portable Air Conditioner - Answered Questions & Fixed issues

E1 error - Indoor room temp sensor defective. Replace it.
E2 error - Indoor coil sensor open. Replace it.

Hope helps.

It sound like the coil inside could be dirty. I have had the same problem with air handlers, when the coil is dirty or the filter is dirty it creates a back pressure and causes the condensation to drip off away from the condensation pan. Try accessing the coil on the inside see if it is dirty, if it is clean it lightly with soapy water and a brush and be carefull not to bend the fins on the coil. If it is clean double check the condensation hose and inlet for the hose for foreign matter.

Sure, here are a few suggestions on where to find a replacement controller for your Sunbeam BL0750 electric blanket:

* **Sunbeam customer service:** You can contact Sunbeam customer service directly and they may be able to help you find a replacement controller. Their contact information is available on their website.
[Image of Sunbeam customer service website]
* **Online retailers:** There are a number of online retailers that sell replacement controllers for Sunbeam electric blankets. A quick search should turn up a few options.
* **Local hardware stores:** Some local hardware stores may also carry replacement controllers for Sunbeam electric blankets. It's worth checking with your local store to see if they have any in stock.

Once you've found a replacement controller, you can either install it yourself or have a professional do it for you. If you're not comfortable installing the controller yourself, you can take your blanket to a qualified electrician or repair shop.

Here are some additional tips for troubleshooting your Sunbeam BL0750 electric blanket:

* Check the power cord to make sure it's plugged in securely.
* Try using a different outlet.
* Check the fuse or circuit breaker to make sure it's not tripped.
* If you've tried all of these things and the blanket still doesn't work, you may need to replace the controller.

I hope this helps!

There is chance that arcing brushes in the motor are causing the odor. They should be replaced and the armature cleaned. A sunbeam repair shop can refurbish your mixer if the parts are still available.

Nothing works. Have had it for 6 months. Plugged in after so long, still blinking.

compressor not working or low on freon

A partstore knows or chec online

heating element possible shorted out.

Try these: -Make sure the remote battery contacts are clean; -clean fully charged battery surfaces with a lead pencil eraser to remove oxide; -could be loose contacts or cold solder joint on remote control board, especially if dropped a lot. if not tech savvy probably better to recycle old unit and purchase a new one . good luck!

Generally means u have a bad connection at the wall or at the control module. Disconnect everywhere u can and reconnect

Possible free manual if this is the same model with wick information. http://www.milesstair.com/Sunbeam3602.pdf

Try unplugging the power cord from the wall socket and check that the connection to the blanket is good and not loose. Then plug back into the wall socket and switch on. If error still occurs then there may be a problem with the blanket.

My sunbeam XL heating pad started blinking and I couldn’t figure it out. I Unplugged a couple of times and still it kept flashing. After hours of reading post, I did what wpart suggested and now it works normal again..... I kept pushing th on off button while plugged in, I unplugged it while still hitting the on off button, I plugged it back in while still hitting the on off button annnddddd drum roll please!!!!!! It started working properly! Thanks wpart, your the MVP and award goes to you!

Wires probably damaged inside. Be carefull, I had one cought on fire. Dont like this things ever since

unplug replug blanket to control connectors plug back in this will continue to happen on these blankets you will have to reset these blankets again and again (chinese junk)

http://www.electricblanketinstitute.com/blanket-or-comforter-on-top-of-electric-blanket.html

You posted this in the Heating and Cooling Section. try another area.

then controller is faulty replace

You can check at any hvac supply house like United refrigeration, fw webb, johnstone supply ,Lennox parts plus or grainger

Hello Carrie, You may be able to download an instruction manual from Sunbeam directly here: Instruction Manuals at Sunbeam com Otherwise, you might need to use their contact us feature and ask directly. I hope this helps!