20 Most Recent
Estate White-on-White TES325MQ Electric Range - Page 6 Questions & Answers
Jennaire gas range, down draft fan jds9865bdp
The Jenn-Air JDS9865BDP is a gas range with a downdraft ventilation system. The downdraft fan pulls smoke and cooking odors down and out of the kitchen, eliminating the need for a hood and providing a sleek, integrated look in the kitchen.
I need manual for broan range hood with light &fan
If you need a manual for your Broan range hood with light and fan, you can find it online. You can search for the specific model number to find the correct manual for your range hood. You can also contact the manufacturer directly to inquire about purchasing a replacement manual.
My Beko HLG Victorina oven will light with the ignition, but the flame stays in heating mode and doesn't settle to a temperature.
The issue you are describing with your Beko HLG Victorina oven may be caused by a problem with the oven's thermostat or gas valve. The thermostat controls the temperature of the oven and tells the gas valve when to open or close in order to regulate the flame.
To troubleshoot this problem, you can try the following:
- Check the thermostat setting to ensure it is set correctly. If the setting is too low, the flame may not be able to reach the desired temperature.
- Check the oven's temperature sensor to ensure it is working properly. A faulty temperature sensor can cause the oven to overheat or not heat up at all.
- Check the gas valve to ensure it is working properly. A faulty gas valve may not be able to regulate the flame correctly.
- Check the ignition system, including the spark plug and ignition module, to ensure they are working properly. A faulty ignition system can prevent the flame from staying lit.
- If the problem persists, it is recommended to consult a professional technician to check the oven, or contact the Beko customer service for assistance.
It is important to note that these instructions may vary depending on the oven model, so it is best to consult the user manual for specific instructions
When my Rayburn reaches temperature instead of cutting out and restarting automatically, it trips out, so I have allow the temperature drop and reset the trip each time. anyone have this problem ?
If your Rayburn stove is tripping the thermal cut-out when it reaches temperature instead of cutting out and restarting automatically, there may be a few different causes.
- Check the thermostat: Make sure the thermostat is properly calibrated and functioning correctly. If it is not, it can cause the stove to overheat and trip the thermal cut-out.
- Check the thermal cut-out: Make sure the thermal cut-out is not faulty. If it is, it may need to be replaced.
- Check the temperature control: If the temperature control is not functioning correctly, it can cause the stove to overheat and trip the thermal cut-out.
- Check the combustion chamber: If the combustion chamber is dirty or blocked, it can cause the stove to overheat and trip the thermal cut-out.
- Check the flue: If the flue is blocked or not functioning correctly, it can cause the stove to overheat and trip the thermal cut-out.
- If none of the above steps work, it is possible that the stove has a more serious problem that requires professional service.
It is important to refer to the user manual or contact the manufacturer for specific troubleshooting steps for your Rayburn stove model. It is also important to make sure the stove is not plugged in before attempting any troubleshooting steps. If the problem persists after trying the above steps, it is recommended to have a professional technician to look at the stove and diagnose the problem.
Hotpoint FDEU 9640 washer dryer - stops during dry cycle with all LEDs flashing amber Hotpoint FDEU 9640 washer dryer - stops during dry cycle with super wash, slow spin, time saver, eco wash and start/pause buttons all flashing. Spin light is steady on. Then about 5 mins later the door unlocks. Wash cycles complete with no apparent issue but drying cycles are stopping prematurely. I have tried auto clean but this trips the electrics. Checked the pump and pipes no blockages. I have opened up the heater unit and that looks clean plus the seals and connections all visibly look good but I don't have a multi meter to test. Please help with any advice - thanks
How to fix a F2-E1 error code
The F2-E1 error code indicates a problem with the oven's key panel. To fix this error, first, try unplugging the oven for 30 seconds to reset the control board. If this does not work, check for any debris, such as food or grease, that may be blocking the keypad. If there is debris, clean it off. If the problem persists, you should contact a certified technician for assistance.
RF365PXKW shows error code F5E1
Whirlpool-KitchenAid-Roper Appliances: Oven Fault Codes:
>>Exception Note:<<
Chart below does not apply to Whirlpool Models using the "Y" line in the products model numbers. Applies to models using 4 digit displays only.
F0-E0 Analog to Digital failure
Disconnect panel for 30 seconds
Should the above error re-appear, replacement of the control is required.
F1-E1 Defective ERC Replace ERC
F2-E0 Shorted Keypad Replace Keypad
F3-E0 Sensor or Sensor Fuse Open Replace Sensor or Fuse
F3-E1 Shorted wire or Sensor locate short and correct it or replace Sensor
F3-E2 Oven over heat Replace Sensor
F3-E3 Cleaning Temp over heat Replace Sensor
F5-E0 Door Error Check Door
F5-E1 Door Latch Check Latch
F5-E2 Door Switch Check Switch
New Hood bulb won't work.
If you are unable to get a new bulb to work in your Allure range hood, but the original bulb is still functioning properly, there could be a problem with the socket or wiring in the range hood. Here are a few things you can try to fix the problem:
- Check the socket for any visible damage or debris. If the socket is damaged or clogged with debris, it may not be able to hold the new bulb securely.
- Check the wiring for any visible damage or loose connections. If the wiring is damaged or not properly connected, it could be preventing the new bulb from functioning.
- Try replacing the socket or wiring if they are damaged or not functioning properly.
- If the problem persists after trying these steps, it may be necessary to have the range hood inspected by a technician to determine the cause of the issue.
If you are not comfortable troubleshooting the problem yourself, it is recommended that you contact the manufacturer for assistance. They may be able to provide further guidance or offer repair options.
Vgic365-4gss lost all power to igniters and oven light and convection fan
It sounds like you are having a problem with the electrical supply to your VGIC365-4GSS range. If the igniters, oven light, and convection fan have all lost power, it is likely that there is an issue with the range's wiring or a problem with the power source.
Here are a few things you can try to troubleshoot the problem:
- Check the circuit breaker or fuse box to make sure that the range is receiving power. If the circuit breaker has tripped or a fuse has blown, reset the circuit breaker or replace the fuse to restore power to the range.
- Make sure that the power cord is securely plugged into the outlet and that the outlet is functioning properly.
- Check the wiring on the back of the range to make sure that all connections are secure.
- If the problem persists after trying these steps, it may be necessary to have the range inspected by a technician to determine the cause of the issue.
It is important to note that working on electrical appliances can be dangerous. If you are not comfortable troubleshooting the problem yourself, it is recommended that you contact a professional for assistance.
Not finding what you are looking for?