Top 20 Venturer PLV31220S1 22 in. LCD TV Questions & Answers

If you wish to get more details; check the sites linked here. It has set-up code list & set-up procedure to many popular brand remote controls.Common codes to check devices with different brand TVs are given, in the order of the device's brand name list in alphabetical order.Pull up older posts. Surf the site with patience. http://remotesearch.blogspot.com/ http://electrohelponline.blogspot.com/

Dust the inside of the disc off, unplug the player, and make sure everything is plugged in right.

If the problem is same with different input devices and you have ensured there are no loose contacts in power outlet, RC jack, cable and sockets, the TV needs servicing.

What are you using as your source of RF. Connection from a Cable TV supplier? - if so Cable TV is all delegated to use their box. Off air digital antenna?- if so maybe you need to set your TV to the 'off air'

Download the user manual to your TV. It will have all details.

Better red than blue or gold.

Good day!!!!

That problem is usually cause of faulty capacitors on the power supply board..
Just follow this instruction to fix your TV..
1. Open the back cover of your TV.
2. Look at the power supply board..Its normally connected to the power cord..
3. After that,,try to look at the actual image of capacitors if it is bulged on the top so that you can easily determine the bad capacitors..
4. After that,,try to replaced the bad capacitors using soldering iron and soldering lead..replaced the capacitors only with the same type ratings and value..
5. Some of the capacitors not bulged so its better if have a capacitance meter

Hi

Power suply,

Check the bad solder on High Voltage transformer T2 & T3.

video board bad

Did you have any success locating these parts? I need the exact same parts too.

Plasma and LCD TV sets are prone to having capacitors in the power supply section fail. This is the most likely cause for the probem you describe. When capacitors fail your will commonly see one or more of the following symptoms.

• No video, Power light is on or blinking.
• TV is making a clicking noise.
• TV takes a while to come on
• Screen is very dim or flickers.

Again, You can get a power supply repair kit with the parts, detailed instructions, and support from sites such as www.TvRepairKits.com . Or just click here to see more details on their kit.

Here are pictures of capacitors...Notice that the ones below look bloated. They have failed and will need to be repalced.



Capacitor being replaced! Fairly easy DIY fix.


Again, You can get a power supply repair kit with the parts, detailed instructions, and support from sites such as www.TvRepairKits.com . Or just click here to see more details on their kit.

It may be that the lens is dirty so it can't read. Try inserting a CD or DVD cleaning disk (like a normal disk but has a little brush attached)
If you are trying to use home recorded disks check that they are in a suitable format - some players require only R- format whilst others will only R+

Hello, this is Becki Barned with DISH Network customer service. I enclosed a link to our website, where you will find the information on doing a power scan to get the remote working with the tv. Hope this helps if you haven't gotten this resolved already.

http://www.dishnetwork.com/SupportSection/power-scan-instructions


Becki Barned
DISH Network Customer Service

I don't think it's the remote nor the I/R sensor that's bad. It might be a processor problem on the control board - need to troubleshoot further. Since it is intermittent, I believe it's a cold solder connection on the board. You can inspect the board and try to locate the bad connection and re-solder.

The Pause button has two vertical parallel lines. It's next to the play button.

Press "interactive" button on remote
Go down to 4 "customer service", press select.
When the customer service page comes up,
Go down to 5 "program your remote" then press select

Then follow the on screen instructions.

This service is free and does not access your phone line at all.

Replace power supply or fix bad caps

It depends entirely on which universal remote control you have. There is no specific code for one TV for all remotes. Different remotes have different codes and remotes that are older than the TV don't always have a code that will work anyway.

If you can post back with your remote brand and model number, I will try to obtain the correct code for you.

I had a similar problem with my 42 in Philips LCD HDTV.

Here was the problem. My Power Supply Board had several bad capacitors. I opened my TV (warranty was expired of course) and found four bulged capacitors on the PSB. Many major electronics companies Philips/Magnavox, Sony, Panasonic, and others were sold capacitors that failed in 2-5 years instead of 10-20. The capacitors fail prematurely due to a lack of preservatives. Unfortunately, they were installed in all sorts of devices and cause a wide range of failure problems.

Here are some options for you.

1. Have it fixed by a professional $$$$$$$??????? (Is it under warranty?)

Remember, TVs CONTAIN HIGH VOLTAGE AND CAN KILL YOU! Do this at your own risk.

2. Open your TV and find PSB. (The board that the power cord plugs into) Check for faulty caps. If you find some (bulged or leaking) bad caps replace the entire board. The entire board costs around $250 right now because they are in high demand right now. They can be found online. I would definitely shop around though.

3. Remove and then replace individual faulty caps. This takes some soldering skill.

Caps are inexpensive and if you can take care of it yourself it will save you hundreds.

This may be your problem. If you determine that it might be.

I have a Tip/How TO tutorial on this site that may also help. It gives step by step instructions for replacing caps on PSB #715t2432-2. If this is your board you are in luck. Here is the Link: Fixing the Philips Turns/shuts off on its own problem. I'm working on uploading pictures to help guide people though the process as well. Let me know if I can do anything to help.

Hope this helps and if it does please rate it accordingly. Good luck.

ck format in main menu