20 Most Recent Sharp 32SC260 32 inch TV - Page 9 Questions & Answers

Your troubleshooting has isolated the problem to power supply failure.

This is usually a sign of a component failure in the power supply called a capacitor. Unless you are versed in electronics, the best thing is to order a new power supply board. Being the age that it is there may not be any made any more

Diodes dont get cut in half. There is no schematic available for that unit. Your best bet is to get the board that it is on and replace the whole board if you can. Diodes dont oscillate, they rectify. The only way around this issue is to get a meter and measure the voltage and then measure the impedance and calculate the current and look for a diode with those specs.

The blinking "standby light" suggests a failing power supply.

Plug all 5 wires instead of just the usual 3

If you wish to get some details; check the sites linked here. https://elektrotricks.blogspot.com/ https://electronicshelponline.blogspot.com/ Faults & possible causes to LCD screen are given with illustrations. You can get an idea about the fault to an extent. Search the site by type in the Brand Name of your set, in its search bar at the right side column, and press enter. See it in Webview with mobile or by desktop. Mobile View has no search box.

try to look for this manual..https://manualzz.com/doc/1102543/sharp-21g-fx10la-service-manual

Change Remote PCB capacitor and Transistor

No of blinks could indicate error codes. Count it. Then google for Sharp TV error codes.

What connectors are you using to connect it to the TV? Start with the basics. Try this. Remove each cable, one at a time, at the TV end and take a good look at it. Check for any dirt or damage. Any damage to the cable or connectors replace it. Most TV/Audio cables are usually quite cheap to buy new, even the higher quality ones. Refit the cable the correct way around and push gently but firmly so it goes all the way into position. DON'T force it in! Most connectors are specially shaped so they will only fit one way around. Repeat this process at the Freeview Box end of the cable. Sometimes loss of picture or sound is just a loose cable connector that isn't pushed all the way into place.

Unplug the television overnight. Plug in the next day. If it is still there, try the software update again. If it still fails, contact Sharp Support and ask for a new television!

Back - light problem. Check and replace damaged component/s at its back-light inverter board, or replace this board as card basis. If you wish to get some details; check the site linked here. Pull up older posts or search the site by type in the brand name of your set, at its search box at the right column.. It will be best to replace the inverter board as card basis. http://electronicshelponline.blogspot.com/ https://elektrotricks.blogspot.com/ Search the site by type in the brand name of your set, in its search bar at the right side column, and press enter. See it in Webview with mobile or by desktop. Mobile View has no search box.

try a different input

Channel three or channel four or get a CRT TV then to play your PS2 console.

Hola Curtis White, en cuanto a lo que vengas de tu Sharp TV, la posibilidad de falla puede estar en el Tablero T-Con o en el Tablero Principal, como ?ltima opci?n falla en el panel LCD Sugerencia conectar con un servicio t?cnico especializado Sharp Espero que puedas resolverlo Saludos, Franco Dosil Hola Curtis White, por lo que cometas de tu TV Sharp, la posibilidad de falla puede estar en la Placa T-Con o en la Placa Principal, como ultima opci?n, falla en el panel LCD Sugerencia conectate con un servicio t?cnico especializado Sharp Espero que puedas resolverlo Saludos Franco Dosil

Gonna cost u mor to fix then a new one at wal*

my repair man once told m he could try cleaning the contacts in my remote .

WHY DO YOU HAVE TIMER SET i KNOW HOW TO TURN IT OFF WHEN I GO TO BED

CAN NOT SAY AS WE DO NOT DO REPAIR WORK HERE ONLY GIVE WHAT ADVICE WE CAN