Top 20 Kenmore HE5 Questions & Answers

change the gas coils on the gas valve by removing the 2 screws holding the bracket for the coils,remove the wire harnesses to each coil,dont worry one coil has 2 wires the other has 3 so quite hard to reverse

The fault code E1 means the electronic control detected the thermistor is open. It's either the wire harness connecting the thermistor and electronic control is broken or the connection is loose or the thermistor is indeed open. Measure the resistance of the thermistor then refer to the temperature and resistance table for the normal thermistor resistance values.

Troubleshooting Error Code E1 on Kenmore Elite and Whirlpool Duet Dryers

Hi, If you have a gas dryer.
The most common problem with a gas and no heat is the ignitor going bad...

Here is a tip that I wrote about that problem...

Gas Dryer not Working Gas Dryer Not Heating
http://www.fixya.com/support/r4398592-gas_dryer_not_working_gas_dryer_not

If your dryer is electric..
There could be a number of different problems...
Check out this tip that I wrote about this problem...

Dryer Troubleshooting Electric Dryer won t Heat
http://www.fixya.com/support/r3866345-dryer_troubleshooting_electric_dryer_won

heatman101

Hello. I recommend that you replace the entire plug and cord with a new one. The one that shorted is one of the two hot wires. It could be that the plug was faulty or had a weak spot in it. Joe

reattached the felt ring correctly around the drum to make it run quite again

This is a communication error with the motor. The first spot I would check the MCU on the lower front of the unit. Remove the lower front panel three screws check the wires there unplug and plug back in if that does not work check the wires on the top board. The top has three screws in it then it will slide back and off.

The F21 Error is a LONG DRAIN error. The manual tells you to check to make sure your drain hoses are not clogged or routed badly. In reality, I just had to clean out the gunk trap. It's pretty easy. Remove the front kick plate, and there is a plastic thing that you twist and pull out. Clean out all the socks and such, and twist it back in. Then clean up all the water that leaked out onto the floor.

If you have a leaking FRONT LOADER, the following link explains how to access and inspect your washer for leaks:

http://www.fixya.com/support/r3576656-washer_leak__front_loader

In the majority of the cases with front loaders, the door bellow begins to leak. A routine inspection of the seal perimeter will tell you if there are any rips or tears. If the bellow is damaged, it must be replaced. The following link explains how:

http://www.fixya.com/support/r3574186-installing_a_door_bellow_on_a_front_load


Replacement parts (if required) can be purchased at any of the following websites:

searspartsdirect.com
pcappliancerepair.com
appliancepartspros.com
repairclinic.com

All these sites are reputable and offer great service with competitive pricing, so shop and compare. The first three sites I listed also include helpful exploded view parts diagrams to assist you in locating and properly identifying the parts you need.

Follow the tips in the links provided and make sure you inspect all the drain hoses, drain pump cover and tub seals as well.

If you have any questions, please post back and let me know. I hope you find this information helpful.

The problem is the water in the vent pipe.You will have to empty the water out of the vent pipe. If the vent is running under the house, crawl under, starting at the closest dip to the dryer and work it out to the exterior. Then use some wire or ties to secure it to the floor joists to keep the dips from reoccurring. If there is water in the pipe, then the dryer can't blow the warm, moist air out of the tumbler. It is the equivalent of trying to dry clothes in a sauna. There is nothing wrong with the dryer, it is working correctly. The problem is the vent.

The Control Lock is a safety feature that enables the consumer to lock the control panel to prevent small children from manipulating the controls and accidentally starting the appliance. This can usually be reset and does not require a technician.

With the lock on, the control panel is disabled and you cannot use any of the controls, except the button to unlock it. It can inadvertently be set following a power outage, leaning against the control panel, or pressing and holding the wrong button. This is usually not an indication of a malfunction.

If this is a Whirlpool manufactured front loader, the following link explains how to lock/unlock this feature:

http://www.fixya.com/support/r3608801-control_panel_lock


These instructions are also printed on the front panel of the appliance and in the owner's manual.

If this does not correct your problem, then you may have a more serious problem than a simple operator control button issue (such as an operator console problem or main control board issue).

Please post back if you still need assistance. I hope this helps you.

F20 on Kenmore indicates a problem with the water inlet AKA insufficient water supply. Start by checking the water inlet hose. It it kinked or clogged. A variety of clogs can be found in the inlet hose such as coins clips etc., so make sure you check it thoroughly. It may also be possible that there is some ice blocking the inlet(Thanks to the cold weather). So if you live in a cold place then this is ice is one of the biggest problem you can face. If there's nothing wrong with the inlet then check the water faucets and see if they are on. If you have found nothing after checking all of the above mentioned things, then its probably time for you to call a serviceman to check it thoroughly. If you can get me your zip code I can search our repair directory and give you the list of service men in your area.

Hope this helps,
Sai.

The heating element have got old and brittle over time and finally gave up the ghost. But it is not always the element. It could be one of the safety Hi-limits have blown. All parts of the dryer will have continuity if its working properly. Test for continuity by using a meter set on Ohms,or use a poor man's meter. You can make your own poor man's meter by using an ordinary flashlight . Break the circuit in the flashlight and add a couple of wires to it so that you can make the light come on in the flashlight, that's right hot wire that flashlight. When the bulb lights up you have a circuit! You now have a poor man's meter. The next step is to check each little gizmo on the dryer that the wires attach to. All the limits attached to the side of the heat element, the door switch (when door is closed) etc.should have continuity (closed circuit)(the light should come on in the poor man's meter) If you come across an thing near the blower housing with 2 wires attached to it, that is a thermal limit, a safety or a control thermostat (So as not to get a false circuit you need to remove one of the wires to each thing you check) Look for lint buildup or blocked vent going out the house. If everything is good and you have paid the electric bill, then the timer could be bad.

this can be normal in some models it can be caused by dry softner in dispenser

It appears your timer/main controller/CCU has failed in this instance.

For replacement parts - head on over to PartSelect.com or RepairClinic.com and enter in your full model number for a full parts listing.
I recommend both sites because ...


FixYa has no affiliation with either site - I have been using and recommending them for years - trouble free.

PartSelect has a great schematic database for locating the part on your unit and great "testimonials" for each part that often times includes HOW-TO information.
RepairClinic has pictures of each part they sell and also a great how-to and troubleshooting for basic repairs.


If your unit has never been serviced - there should still be an original service manual enclosed in plastic taped to the inside of the shell.
In the service manual are Error codes, maintenance procedures, and troubleshooting steps you can follow.


Anything too complicated or beyond your scope should be handled by a professional.

If you think you want to tackle the repair - and have gotten stuck on a step - reply to your question and I will be glad to help you out.




Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question

I have the same problem . If I power cycle mine enough times I eventually get a F70 or F71 code. My research online suggests that the user interface board has a problem and needs to be replaced.

The good news is the warranty covers these boards for two years. The bad news is they are $360 if you are out of warranty.

HTH

HI. This is a Serial communication error

Communication between the Central Control Unit (CCU) and the Motor Control Unit (MCU) cannot be sent correctly.

Potential Causes

• Check Wire Harness connections to the MCU, the motor, and Central Control Unit (CCU)
• Check the Drive system for any worn or failed components
• Check MCU
• Check CCU
• Check Motor
• Check Wire Harness

Replace failed component.(usually the wiring harness will need to be replaced in this case, but a faulty Motor Control Board is not uncommon)

your water solenoid is probably not closing completely and letting water by pass. Not sure what your model number is but you can find this part and others at www.Repairclinic.com Good luck.

110.2808 is an incomplete model number. Motors are typically $140 to $180 USD https://www.easyapplianceparts.ca/PartInfo.aspx?inventory=334304&SourceCode=18 This is is a typical Kenmore model designation and is probably the matching washer to your dryer. Yours is missing 4 numbers. Label in the back, label on the door frame, mentioned on the manual.

Model # 11028081700 Official Kenmore Elite washer

https://www.google.com/search?q=Kenmore+elite+electric+dryer+110.2808 ..

Yes, it looks like you can. Don't forget though that you have to get inside and move the door switch. https://www.google.com/search?q=Kenmore+Elite+Quietpak+4+reverse+door ..

The are various idea here.

I have model and serial #s for my washer/dryer. What year ...

iFixit https://www.ifixit.com > Answers > View > I+have+m... Apr 3, 2017 - I have a Kenmore washer and dryer. I have the model #s and serial numbers. I need to know what year ( how old are my appliances?) of the models. 4 answers · Top answer: Erin Morrissey , How to find out the manufacture date of a Kenmore washer or dryer by the ... How old is my dryer? - Kenmore 110 Series ... 2 answers Mar 11, 2022 How old is my kenmore washer/dryer combo? - iFixit 2 answers Aug 4, 2018 help me find out how old this washer is - iFixit 2 answers Sep 29, 2021 What is this dryer model number? - Kenmore Elite ... 2 answers Jul 18, 2016 More results from www.ifixit.com Missing: 110.77741600 ‎' Show results with: 110.77741600

Can you tell me the age of a dryer from the model or serial

JustAnswer https://www.justanswer.com > Appliance Repair May 19, 2023 - Can you tell me the age of a dryer from the model or serial # Kenmore 600. Model is 110 78652700 serial is - Answered by a verified ... 1 answer · Top answer: Good afternoon. My name is ***** ***** I'll be assisting you with your appliance today. Please ... Missing: 110.77741600 ‎' Show results with: 110.77741600