Top 20 Heavyduty Jazzy 1121 Standard & Heavy Duty Power Wheelchair Questions & Answers

Pride Mobility Jazzy 1121 - USA TechGuide

www.usatechguide.org/itemreview.php?itemid=570 19 posts - ‎16 authors Medium Back Seat Contoured Medium Back (standard). ... Comments: My jazzyscooter goes forward and side to side but the reverse makes a quick .... Strengths: Tough chair - town I live in doesn't have many curb cuts, but chair will climb ....Maneuvers poorly through (Handicap) doorways, due to rear locked caster wheels.

check with a voltmeter to be sure charging voltage is present.

Page 20 will describe how to remove the seat. P38 and on will describe how to change the batteries. Hope this helps Pride Mobility Products Corp Product Owners Manuals Specification Sheets

yes nplug battery charger in and wait till batterys asre fully charged and turn off,if it doesnt u got water or moisture in the joystick and need a new one

joystick may need to be reprogramed

Try Pride Mobility, eBay or Monster

I had the same problem I had to replace the batteries problem solved.But the batteries are not cheap

Code 8 Controller system fault...

This is taken from the owner's manual from the 1121 with a VSI controller:

I suggest you print this out and keep it handy.Locking/Unlocking the VSI

The VSI has a feature that enables you to

lock your power chair to prevent unauthorized use.

To lock the VSI:

1. With the VSI switched on, press and hold the on/off key. After 1 second, the VSI should beep.

2. Release the on/off key.

3. Push the joystick to the full forward position until the VSI beeps.

4. Pull the joystick to the full rearward position until the VSI beeps.

5. Release the joystick. There should be a long beep.

6. The VSI is now locked.

To unlock the VSI:

1. Press the on/off key and power on the VSI. The maximum speed/profile indicator should ripple up and down.

2. Push the joystick to the full forward position until the VSI beeps.

3. Pull the joystick to the full rearward position until the VSI beeps.

4. Release the joystick. There should be a long beep.

5. The VSI is now unlocked. NOTE: If the above procedure fails to either lock or unlock the VSI, contact your authorized Pride Provider.

log onto pridemobility.com and select jazzy then select user manuals then look under discontinued models and find Jet 2 you should be able to download the manual Hope this helps

candy probably a battery issue but it could also be a charger problem also If the batteries had gotten really low then the charger is not designed to pickup really low voltages. If possible have your provider (Where you got the chair) check the batteries and charger for you Hope this helps

you have either bad batteries or a bad charger or the charger might have come unplugged at the controller or power module. When you have the charger plugged in and you turn on the joystick the lights on the joystick should ripple to indicate the charger is plugged in. If you don't see this ripple then either the charger is bad or disconnected. Trace the charger cable from the rear of the chair (you have to remove the seat and shroud to do this) to the front module and make sure that the cable is plugged in. Hope this helps

You can visit this website to find answers on what the flashing trouble indicator lights mean: http://www.pgdt.com/scenter/diagnostics/diagvsi.html
Locate the page that has the controller used on your power chair/scooter and count how many lights are flashing to diagnose the trouble. If your insurance purchased the power chair for you, they may also cover the repairs; contact them for information.
Good luck!

Pudn it is at the rear of the chair on the right hand side of the shroud above the joystick connector Hope this helps you

Jackie I looked on the Pride Website and threy showed them behind each drive wheel above the motor facing the rear of the chair. Lift to place in freewheel and push down to engage. I hope this helps you

I believe the older versions had a release lever and cable system at the rear center. This was a 2 step, 2 handed on your knees process to release the lock on lever with your left hand and pull out and turn the lever with your right hand. This pulled on the cables to both motors to disengage the freewheel levers

The number of lights that are blinking indicate what the problem is. Visit this site to locate the type on controller on your power chair and you will be able to see that the blinking lights mean:
http://www.pgdt.com/scenter/diagnostics/diagvsi.html
Try to reset your manual brake release as this is a common problem.
The powerchair going in circles may indicate a motor is bad and needs to be replaced.
If you continue to have a problem, contact your manufacturer or dealer for service. If your insurance purchased they power chair for you, they may also cover the cost of repairs.
Good luck!

Yvone You will have to buy 2 batteries for your chair. You need two U1 batteries and if there is a battery warehouse or Interstate Battery store near you they can be purchased there. You can also go through a wheelchair provider but the cost will be higher. Buying on-line might be ok but shipping will be high. Hope this helps you

Make sure that your tires are properly inflated and that you are not carrying more weight than the power chair will allow and that your batteries are fully charged.
If you got your chair second hand, sometimes the previous owner has the technician change the controller settings to "dampen" it to slow it down to allow them greater response time and control. The technician can reprogram the controller to take it back to 100%. If you got the power chair new, it should be at 100% already.
Take it easy, HotRod. It's a medical device, not a car!
Good luck!

make sure your free wheel levers are in the correct position