Top 20 Pramac GX565AUV000 NA GS Series 5500 Maximum Load Capacity Manual Hand Questions & Answers


Hi is it electric or a manual pump up with the handle type if its one these check the oil level in the unit it may just need more hydroloc oil added or the valve on the actual jack of the unit its self are leakin and need replaceing dont use it like this as very dangerous
,

Pramac... | 1,523 views | 0 helpful votes


There's no question here.

Hoisting | 417 views | 0 helpful votes


make sure the pallet hindging point be free od dust... since it is open....lubricate and check ... it will work

Hoisting | 1,301 views | 0 helpful votes


talk with a doctor
this page has no medical advice

Hoisting | 198 views | 0 helpful votes


First of all clean the jacks very thoroughly. If they are really dirty, tap gently with a hammer to release sand and dirt, hose thoroughly, repeat. Lubricate every part of the jack with lots of wd40. Check that the part of the jack that extends down has been fully released and pushed up into the upper portion of the jack. Then grasp the jack with both hands and tug it down. While the jack is pulled down, swing it up under the trailer until it clicks into place.

Hoisting | 1,561 views | 0 helpful votes


What about it?
If you have doubts about a safety related item get an engineer to call.

Hoisting | 1,005 views | 0 helpful votes


I found this set of instructions to be very detailed and helpful when I had to set up my wire hoist. Good luck and stay safe!
http://voices.yahoo.com/how-install-wire-rope-hoist-7673214.html?cat=6

Hoisting | 1,309 views | 1 helpful votes


Common ratchet lever hoists have the capasity to lift up to 5 tons, but some can only lift 1/2 ton its important to consult your user manual for exact numbers before use.

Hoisting | 1,241 views | 0 helpful votes


OSHA is the United states department of labor Occupational safety and health administration. They have to inspect your wire hoist every year to make sure that you and your employees are safe when they are using the wire hoists in your facility.

Hoisting | 1,231 views | 0 helpful votes


Wire hoists are as strong and in some cases can be stronger even than chain hoists being able to lift between 1/2 up to 80 tons.

Hoisting | 1,222 views | 0 helpful votes


There are a lot of automatic chain hoists and you will find that they work much faster and with less effort than manual ones.

Hoisting | 1,178 views | 0 helpful votes


The full process of dismanteling your buck hoist should be a day.

Hoisting | 1,018 views | 0 helpful votes


Needing a permit to build a buck hoist depends on where you are building it. Only a few states in the US require you to get a permit and the elevator to be inspected. Indiana, Michigan, Arkansas, Washington, Nevada, North Carolina, California all require you to get a permit.

Hoisting | 985 views | 0 helpful votes


Depending on the hoist that you are renting the capacity ranges from 4000 lbs. to 8000 lbs. Before you start loading up your hoist make sure to check the capacity of the one you're renting.

Hoisting | 956 views | 0 helpful votes


"A jack lift is a mechanical device used as a lifting device to lift heavy loads or apply great forces. Jacks employ a screw thread or hydraulic cylinder to apply very high linear forces.
A mechanical jack is a device which lifts heavy equipment. The most common form is a car jack, floor jack or garage jack which lifts vehicles so that maintenance can be performed.
More powerful jacks use hydraulic power to provide more lift over greater distances. Mechanical jacks are usually rated for a maximum lifting capacity (for example, 1.5 tons or 3 tons)." (Wikipedia)

Hoisting | 927 views | 0 helpful votes


As the name suggests, for manual pallet jacks you walk behind the forks and pump the handle to raise them/lower them. On powered, or electric, pallet jacks, there is a throttle for moving and a lever for raising/lowering the forks. On some powered pallet jacks, there is a platform for the operator to stand on

Hoisting | 2,286 views | 0 helpful votes


First of all, the forks are not supposed to go all the way down to the floor, that would defeat the purpose because they would drag and you wouldn't be able to pick up a pallet. But if you think the forks should be able to go down further, just stand on the forks while pulling the lowering lever. You may need to grease the machine

Hoisting | 2,122 views | 0 helpful votes


Pallet jacks may also be called pallet trucks, pump trucks, or jiggers

Hoisting | 1,116 views | 0 helpful votes


Do you see a hole for the plug? It's leaking some oil?

Hoisting | 1,178 views | 0 helpful votes


I would recommend lubricating the entire system every couple months. Also OSHA has to inspect it every year

Hoisting | 1,506 views | 0 helpful votes

Not finding what you are looking for?
Pramac GX565AUV000 NA GS Series 5500 Maximum Load Capacity Manual Hand Logo

1 questions posted

Ask a Question

Usually answered in minutes!

Top Pramac Hoisting Experts

AZBen
AZBen

Level 3 Expert

220 Answers

Andrew Taylor
Andrew Taylor

Level 3 Expert

33449 Answers

gbob59

Level 3 Expert

3063 Answers

Are you a Pramac Hoisting Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Pramac Hoisting

  • Pramac Hoisting

Most Popular Question

pallet not lift

  • Hoisting
Loading...