20 Most Recent Malibu Intermatic Inc. ML121RT Low Voltage 121-Watt Power Pack with Timer - Page 9 Questions & Answers

It is possible that there is a bad ground connection somewhere between the lights and the timer, especially if the problem persists even after replacing the timers. It is also possible that the lightning strike caused damage to the electrical system, which could be affecting the GFCI outlets. It may be a good idea to have an electrician inspect the wiring and outlets to ensure they are safe and functioning properly.

connect white with white, black with red

You did not specify exact make and model. However Microsoft Word - BX1165A.doc (marktime.com) manual may help you.

We need 'make model (what it is)' to get any context of what you are referring to. Impossible to answer otherwise.

Based on the information you provided, it would be like describing an electrical cover or box with some wiring harness. It is important to note that working with an electrical system requires caution and knowledge of electrical safety practices. If you are unfamiliar with electrical work, it is best to seek the help of an electrician to avoid potential hazards. Having said that, if you're looking for the end of the earth, it's usually indicated by a landmark (square with a horizontal line) or the letter "E". There is one that helps with surge protection and proper grounding of electrical appliances.

what is model number. since there are repair parts available for most oscillating sprinklers, they have worn out.

check these sites... https://www.google.com/search?q=ace+programmable+1+zone+digital+water+timer+manual Best to you.

If your Aqua Plus timer is successfully turning on the filter but is not turning it off automatically, there could be a few potential causes for this issue:

1. Timer Programming: Double-check the programming of the Aqua Plus timer to ensure that the off time for the filter is correctly set. Verify that the timer is configured to turn off the filter at the desired time. Review the user manual for the Aqua Plus timer or consult the manufacturer's website for detailed instructions on how to properly program the timer.
2. Timer Power Supply: Check the power supply to the Aqua Plus timer. Ensure that it is receiving a consistent and uninterrupted power source. Any power disruptions or fluctuations can affect the timer's functionality. Confirm that the timer is properly connected to the power source and that there are no loose or damaged connections.
3. Defective Timer: It's possible that the Aqua Plus timer itself is faulty. If all the programming and connections seem correct, but the timer still fails to turn off the filter, it may require replacement. Consider contacting the manufacturer's customer support or consulting a pool professional for further assistance or potential warranty coverage.
4. Manual Override Switch: Some timers have a manual override switch or button that allows you to manually turn the filter on or off regardless of the timer settings. Ensure that this switch is not inadvertently set to the "On" position, as it would override the timer's control.

If you have exhausted these troubleshooting steps and the issue persists, it is recommended to reach out to the manufacturer's customer support or consult a professional pool technician. They can provide further guidance and assistance in diagnosing and resolving the issue with your Aqua Plus timer.

hi find link for https://homeguides.sfgate.com/programming-lawn-genie-82871.html

Nuts....seems like the only info is "TC-PM" Error message TC-PM indicates that there is a problem with the unit, and it is recommended to be serviced. Contact Brother Customer Support: https://www.brother-usa.com/contact-us here's a dealer locator..... https://www.brother-usa.com/dealer-locator

How to set the time on a intertek 3175559 clock

Fixya https://www.fixya.com > support > t26129610-set_tim... Try hold both the time and set button for a period of 5-10 seconds and see if this will cycle the time to normal. If not try hold the set button alone for 5-10 ...

• Changing time in intertek 3175559 clock radio

  https://www.fixya.com > support > t21163337-changi... Nov 3, 2013 - You need to reset the microprocessor in the Clock/Radio. to do this you must unplug the Clock/ Radio and remove the battery.

There is no manual available online https://www.google.com/search?q=manual+for+Micronta+executive+timer+63-783 ..

try this turn on the light at night if it doesn't turn off after say 5 minutes (you should be able to set the stay on time) switch off and back on for most security light operations that action places it in the watch mode the light will come on immediately but will go off after the set time period from then on any intruder movement should set it on fort the set period of time

If there was a brief power outage and your light timer is not working, there are a few steps you can take to troubleshoot the issue:

1. Check the timer settings: Make sure that the timer is set correctly and that the time and program settings are accurate. If the timer has lost power, it may have reset and will need to be reprogrammed.
2. Check the power source: Ensure that the timer is receiving power by checking the outlet or circuit breaker that it is plugged into. If the outlet or breaker has tripped, reset it and try again.
3. Check the timer battery: If your timer has a battery backup, check the battery to make sure it is still functional. If the battery has died, replace it with a new one.
4. Reset the timer: If none of the above steps have worked, try resetting the timer to its default settings. Refer to the user manual for instructions on how to reset the timer.

If the above steps do not resolve the issue, it's possible that the timer has been damaged due to the power outage. In this case, you may need to replace the timer or seek the assistance of an electrician to diagnose and repair the problem.

Based on the symptoms you have described, it's possible that there may be an issue with the ballast or the lamp in your Sunquest Pro 24 tanning bed. Here are some steps you can take to troubleshoot the issue:

1. Check the power source: Ensure that the tanning bed is plugged into a working electrical outlet and that the outlet is supplying the correct voltage. You can use a voltage tester to check the voltage.
2. Check the ballast: The ballast is a device that regulates the electrical current to the lamp. If the ballast is faulty, it may prevent the lamp from lighting up. Check the ballast for any visible damage or loose connections. If you're comfortable with electronics, you can also use a multimeter to check the ballast's continuity.
3. Check the lamp: If the ballast is functioning correctly, the issue may be with the lamp. Check the lamp for any visible damage or dark spots. You can also use a continuity tester to check the lamp's continuity.
4. Check the timer: If the timer is not functioning correctly, it may prevent the tanning bed from turning on or lighting up. Check the timer for any damage or loose connections.

If you're unable to identify the issue, it's best to contact a qualified technician or the manufacturer's customer service for further assistance. Tanning beds use high-voltage electrical components that can be dangerous if mishandled, so it's important to take proper precautions and not attempt to repair the tanning bed yourself unless you're experienced with electronics.

'I' is probably for Interval. The check mark is for On. https://www.google.com/search?q=Nona+timer+TM1702 ..

hi find link for user manual https://manualzz.com/doc/en/1512703/schumacher-electric-mc-1-owner-s-manual