The rope may be bound up in the recoil. Take the recoil cover off(the piece where the pull rope goes into) and try to pull the rope with the housing off. If it pulls freely try turning the engine by hand, you may want to remove the spark plug to release the compression. If the unit will not turn over,then the pressure pump may have failed. Best of luck.

Honda Karcher... | Answered on Apr 23, 2010

0 Answers

Difficult to start

Honda Karcher... | Posted on Apr 05, 2010 | Be the first to answer

1 Answer

I purchased a reconditioned Karcher 4000 and upon

Bleed the system by running water without the unit on, You have an air lock, open the drain cocks and allow water to run slowly for 2 minutes, then close everything and try it

Honda Karcher... | Answered on Mar 07, 2010

0 Answers

Honda GX390 pressure washer. When trying to

Honda Karcher... | Posted on Mar 05, 2010 | Be the first to answer

1 Answer

Unloader Valve - Karcher Pressure Washer

where is the unloader valve locaed on a Briggs Stratton pressure washer?

Honda Karcher... | Answered on Oct 03, 2009

1 Answer

Hesistation on pressure when trigger is pulled get n worse

Unloader valve is the most likely suspect here.
Remove and clean with penetrating oil then reinstall.

Also add some LIGHT oil into your supply hose via a small funnel. 3-in-1 household oil or power steering fluid lubricate the valve and pump quite well. Three or four treatments of a couple ounces each will usually make the pump happy again. If this unit has an OIL-FILLED pump on it you can expect good results. If it runs an OIL-LESS pump it is only rated for about 100 total hours of life!
Hope this helps.

Honda Karcher... | Answered on Sep 28, 2009

1 Answer

My Karcher 4000 SHR Pressure

it sounds like your unloading valve is crudded up with mineral deposits and stuck in a partway open state. look for a plastic cover with a silver snap on top; pry off the silver snap and lift off the plastic cover; next remove the two screws on the top plate then pull out the piston inside - if unable to lift out, start unit and watch it pop out - coat piston with lithium grease and reinstall - it will work great

Honda Karcher... | Answered on Aug 21, 2009

1 Answer

Honda gas power pressure washer runs for awhile then cuts off.

did you pour all of the old gas out before you started to use it. Sometimes condensation builds up in gas tank when stored. You need to dump old gas an put in new gas.

Honda Karcher... | Answered on Jul 28, 2009

1 Answer

John deere pr4000gh with 13 hp honda gx390 engine. I checked pump oil when I got it home. It was milky white. do I just change pump fluid and hope for the best? I put a new recoil starter on it also.

Per owners manual... WATER PUMP OIL IMPORTANT: If oil is white or foaming, water is in the oil reservoir. Change oil.NOTE: Water in oil occurs as a result of spray or condensation. Milky oil is not indicative of a pump malfunction.

Honda Garden | Answered on Dec 26, 2020

2 Answers

I have a Honda GCV 160 on a lawn mower. I put new carb, plug and wire air filter change oil. 1 st time started, 1st pull. I cut the lawn and it ran fine. Few weeks later, it wouldn’t start with out starting fluid. Next time hard to start but did with starting fluid. Ran fine when I stopped it to empty bag I could never start it again. I can’t find any trouble shooting, other then carb,air filter, plug or oil. Which are all new and it ran fine. Any ideas on what I can check?

And check operation of auto-choke.

Honda Garden | Answered on Dec 23, 2020

1 Answer

13hp honda pull start wont engage.rope recoils,but doesn't turn the engine

it needs to be taken apart to see whats broken inside

Honda Garden | Answered on Nov 24, 2020

1 Answer

I have a power washer Honda 6hp GC190 no fire too new plug . I replaced coil (new)still no fire there's no low oil switch Any help will be appreciated Thanks DLH

Check for continuity on the ignition module kill wire to engine block. Without the oil sentry there should be a single black wire from the ignition module to the ignition switch. This wire goes to the ignition switch and when in the OFF position connects to engine frame to disable spark.

You could disconnect the kill wire at the ignition module and then check for spark. If spark then the kill wire or switch is connected to block (short) or bad switch.

Honda Garden | Answered on Nov 22, 2020

1 Answer

How to Replace belts on Honda HS 724 TA/A snowblower

Turnoff the engine & detach the spark-plug wire.unscrew the belt cover bolts which are located on the right side of the unit
Depress the clutch lever to release tension on the pulleys
Place the new drive belt on the pulleys
Replace the belt cover and tighten the screws to secure it in place

Honda Garden | Answered on Sep 28, 2020

Not finding what you are looking for?

Popular Tags

20 questions posted

Ask a Question

Usually answered in minutes!

Are you a Honda Garden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Have a manual for Honda Karcher G4000RH Pressure Washer? Or just drag it here!

View Most Popular

Honda Garden

Honda Garden

m trying pull rope will barely honda

Garden

20 Most Recent Honda Karcher G4000RH Pressure Washer Questions & Answers

Pressure spring location on a 4000g wand/trigger apparatus

Northstar honda 4100 psi

I can't get the recoil starter placed tight back on a Karcher 4000 OH pressure washer with Honda engine

Where is the unloading valve on the 4000 karcher

What is the open position for the choke all the

My honda 4000 psi pressure washer will not release

Karcher proline, Honda GX390 pressure washer, no pressure

I 'm trying to pull the rope and it will barely--honda pressure w

Difficult to start

I purchased a reconditioned Karcher 4000 and upon

Honda GX390 pressure washer. When trying to

Unloader Valve - Karcher Pressure Washer

Hesistation on pressure when trigger is pulled get n worse

My Karcher 4000 SHR Pressure

Honda gas power pressure washer runs for awhile then cuts off.

John deere pr4000gh with 13 hp honda gx390 engine. I checked pump oil when I got it home. It was milky white. do I just change pump fluid and hope for the best? I put a new recoil starter on it also.

13hp honda pull start wont engage.rope recoils,but doesn't turn the engine

I have a power washer Honda 6hp GC190 no fire too new plug . I replaced coil (new)still no fire there's no low oil switch Any help will be appreciated Thanks DLH

How to Replace belts on Honda HS 724 TA/A snowblower

Not finding what you are looking for?

Popular Tags

Ask a Question

Popular Products

Honda Pressure Washer PSI 3000

Honda 8 HP Engine

Honda 25cc 4-cycle Mini Tiller

Honda Black Max 2600 PSI Pressure Washer

Honda Karcher G2400HH-R Pressure Washer

Top Honda Garden Experts

JOHN LAPIER

Marvin

Tim Venetis

Are you a Honda Garden Expert? Answer questions, earn points and help others

Manuals & User Guides

Honda Garden

m trying pull rope will barely honda