Top 20 Tylo SUPER SPORT-U8 Heater 8 kW Questions & Answers

Probably cooked the circuit board as well.

Get son to buy replacement!!!

Tylo SUPER... | 269 views | 0 helpful votes

Call Saunatec Inc. at 888-780-4427 and ask for tech support. We have these in stock.
Technical Support Supervisor

Tylo SUPER... | 177 views | 0 helpful votes

Failure of the older heating system

Pool & Spa | 18 views | 0 helpful votes

Hi Don.
See if this link helps you out. you out.

Pool & Spa | 14 views | 0 helpful votes


Make model manual

Most are online. Or Google maker and phone them.

Pool & Spa | 15 views | 0 helpful votes

with pump off try turning shaft on back try to break loose then try if no luck bad pump motor replace

Pool & Spa | 17 views | 0 helpful votes

You may have to fabricate your own.

Sunrise Simplicity 1 Parts? ' Forums Home > talk > threads > sunrise-simplicity-1-...
Oct 3, 2009 - Hey everyone, I have recently purchased a home with a Sunrise Simplicity 1 pellet stove, and am quickly finding that parts are almost if not ... Missing: baffles ‎' Must include: baffles

Regency Parts
Welcome to the Regency Parts Store a division of the Cozy Cabin Stove & Fireplace Shop. We carry a vast selection of Regency wood stove, gas stove, pellet ... Missing: simplicity ‎sunrise

Replacement Parts ' Stoves & Fireplaces ' My Fireplace ... > ca_en > replacement-parts
Items 289 - 336 of 1174 - PELLET DOOR FRAME WITH HANDLE AND GASKET WITHOUT GLASS. SKU: SE24085-02. CA$180.00. Buy. Add to Wish List ... Missing: simplicity ‎sunrise

Discontinued Manuals for Fireplaces ' Regency Fireplace ... > Customer Care
To download manuals, right-click on a link and choose "Save...". All manuals are in PDF format and require you to have a PDF reader installed on your computer ...

Pool & Spa | 19 views | 1 helpful votes

see if voltage from transformer if yes see if voltage from main board to display also check for cut wire to display

Pool & Spa | 16 views | 0 helpful votes

possible bad temp sensor if using a controller make sure heater all the way up and let controller dictate temp

Pool & Spa | 24 views | 0 helpful votes sells a shell repair kit that will could also try an acrylic repair kit like plast-aid.

Pool & Spa | 32 views | 0 helpful votes

check and test air pump --look up on internet for multi-sites that show how to test

Pool & Spa | 35 views | 0 helpful votes

Press either warm or cold, then press mode. This shift settings between standard, economy, or sleep. You can find this on page 31 of the manual designated below. If there are other questions, the support page suggests you contact the dealer.

Pool & Spa | 15 views | 0 helpful votes

I have absolutely no experience with pools but I have seen online video of the absolute disaster of rushing the job, skipping details, ignoring important instructions and not taking advice.

A pool holds a lot of water and it is important to remember every Imperial gallon weighs 10 pounds - an Imperial gallon is slightly more than a US gallon.
All that weight is pushing down and so level firm ground is a must and all that weight is pushing outwards so attention to the smallest detail is essential and don't forget how the shockwave from somebody belly-flopping into the pool will create huge unpredictable forces on the side...

Sighting it well away from trees will be good and not over drains close to the surface or over inspection or maintenance hatches and don't forget to cover the pool when it isn't being used.

Pool & Spa | 20 views | 0 helpful votes

I suggest you check the intake for something that falls away when the pump is off but gets drawn in a short time after switching on.

It is a not uncommon cause of pumping ills in many scenarios with plastic bags a popular culprit...

Pool & Spa | 35 views | 0 helpful votes

You must have a pressure gauge that measures vacuum. The scale is usually in inches of mercury.

Pool & Spa | 41 views | 0 helpful votes

You may have a vapor lock which is a bubble of air that is stopping the pool pump from priming. Is there anyway to bleed off the air

Pool & Spa | 48 views | 1 helpful votes

If you can see air swirling around, then there's bound to be water moving around. Otherwise you wouldn't see anything moving. You have a small suction leak somewhere. When you don't have the heater turned on, there's less strain on the pump and therefore less of a suction leak. Assuming your heater has an auto-bypass. Use your garden hose to find the suction leak and patch with silicone or pool putty. Or replace o-rings and gaskets. Check plugs and grease ports, etc.

Pool & Spa | 47 views | 0 helpful votes

Not finding what you are looking for?
Tylo SUPER SPORT-U8  Heater 8 kW Logo

Popular Tags

3 questions posted

Ask a Question

Usually answered in minutes!

Top Tylo Pool & Spa Experts

john h

Level 3 Expert

23504 Answers

David Spradling
David Spradling

Level 3 Expert

11652 Answers


Level 1 Expert

62 Answers

Are you a Tylo Pool and Spa Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Tylo Pool & Spa

  • Tylo Pool & Spa

Most Popular Question

shaft broke timer need replace

  • Pool & Spa