20 Most Recent Hayward 1.5hp Pool Pump Motor Motor A O Smith Electric Pool Motor for 56j Frame Motors Ust1152 - Page 4 Questions & Answers

no fixya does not sell anything

Thank you for choosing Fixya, my name is Natalie and I can assist you with this request. I see here that you are looking to obtain a Hayward Comfort Zone pool manual for your heater model cspa xi11. I have reviewed this information with extensive research and have located your free downloads here: https://www.manualslib.com/products/Hayward-C-Spa-Xi-11-3479823.html If it's not clickable, please copy and paste this url into your url. Thank you again for choosing Fixya and I look forward to assisting you again in the near future! Kind regards, Natalie

Universal H-Series Diagnostics Manual - Hayward Pools

http://www.haywardnet.com > pdfs > uhs-heater-tr... PDF Insure Heater is properly grounded and bonded. Read and follow all instructions in the service and installation manual and on the equipment. Failure to follow ... 63 pages

No lights on Hayward 250hed pool heater control panel.

https://www.troublefreepool.com > ... > Everything Else Jun 1, 2021 - If the keypad/display is not getting DC power from the control board for some reason, it would result in no display and no heater operation. 11 posts · I've searched through the forum without success. I have a 9 year old Hayward 250

How do you remove orifice for cleaning?

ask maker first?

Question edited for clarity, full 'make model (what it is)'. Pour hot water onto it to soften the end of the hose. Wear rubber dishwashing gloves to improve grip.

Dear , Please try the below solutions, Solution 1: If the blower prover switch does not close after the blower starts the control will stop the ignition trial go into lockout. The blower will continue to run. Automatic reset is immediate after the switch closes Solution 2: If the blower prover switch opens unexpectedly during operation the control will shut down and attempt to re-light. If the switch does not close after the blower starts the control will go into lockout with the blower running. Automatic reset is immediate after error is corrected Solution 3: If the blower prover switch opens during the postpurge cycle (heater is not fir- ing) the control will display the error code. The post-purge cycle will be com- pleted once the blower prover switch close Regards, Samy

Employ a gas service engineer who is qualified for advice.

You are not alone https://www.google.com/search?q=Hayward+Pro+series+S310S+leaking+at+seams Try applying JB Weld Epoxy putty. If you can drain it, remove the sand clean the seam and apply from the inside, it will last years, or from the outside, probably just a couple. It is a remarkable product. Apply to a clean dry surface for best results.

WaterWeld Epoxy Putty - JB Weld

https://www.jbweld.com > product > waterweld-epoxy-... Ideal for repairing plumbing, fuel tanks, tub and shower, drains, pool and spa, boats and potable water tanks; setup occurs even under water. After curing, it ... ..

you have a short the gfci should have tripped check the wiring make sure nothing touching the case or gfci is connected correctly

I just had this happen. I was struck by lightning so yours might be different. I replaced the display board and the control board and my heater is up and running.

Could the Error code be HS? That is high temperature limit. Perhaps you' don't have enough flow, allowing the heater to heat the water to a temperature higher, than the thermostat setting. Make sure your bypass valve is closed, allowing full flow through the heater. Check your filter pressure differential , and skimmer baskets.
You didn't give your model number, and there are many models. You can go the Hayward website below and select your exact model number and download the manual. The manual will explain each error code.
http://www.haywardnet.com/inground/products/manuals.cfm

possible internal bypass spring bad not letting enough water through

the valve is for pentair check the unions see if they fit

make sure the recirculation pump that goes to heater piping is working

Question edited for clarity. Question moved from Cars and Trucks category. Yes the contactors take all the strain. The internal contacts are probably damaged, just replace it as they do wear out.

check voltage at transformer possible bad

S190tscp takes 175lbs of sand

Soak the shaft and impeller splices with diesel fuel or store bought nut/bolt loosening spray and tap often over 24 hour period while it soaks and permeates the contact area. Tap impeller with a wooden mallet to remove,

http://www.haywardnet.com/pdfs/Heatpump-Troubleshooting-Guide.pdf