Top 20 Electric Mobility Shoprider Electric Power Wheelchairs Scooters Trooper Questions & Answers

hi does the brake click at the rear when moving the wigwag lever ? . Can you check the brushes in the motor ? resistance of the motor should appear as virtual short , the brake resistance should read from 25ohms upto 80ohms, the scooter won't drive if the resistances are wrong .. the controller could be faulty , and i offer a free testing service if you're UK based here's a trouble shooting manual for shopriders .. https://www.gewizrepairs.co.uk/shoprider_service_manual.pdf Regards Rob

From the manufacture of the scooter, Service manuals are given to Techs like me, you have to a certain skill set to repair this type of equipment. I am factory trained and 20+ years experience repairing equipment. I’m happy to assist further over the phone at https://www.6ya.com/expert/bill_bcbb89783b08c489

Dynamic DL5 2i electric wheelchair joystick controller horn switch speed...

U can get replacement keys of E/BAY GO TO E.BAY & TYPE IN SEARCH ( shoprider mobility scooter keys ) there r 8 sites good luck..

Use this link to download a manual for a chair that looks like you photo . www.shoprider.com/forms_2006/manual/manual_6RUNNERDLX.pdf

This is a sign that the Wig-wag control is at fault or motor brushes need attention. Your husband is on the right track. you will need to take to a service centre for attention.

Most likely you need new batteries.

Hi is it making any bleeps or is any light flashing

Battery connections have come apart I’m happy to assist further over the phone at https://www.6ya.com/expert/bill_bcbb89783b08c489

To remove wheel there is one center bolt in the middle of the wheel(13mm). The wheel is a split rim so on the inside of the wheel there is more 13mm nuts undo them and the wheel comes apart.(no need for tire levers)

Remove the axle and drop off the tire. Tools needed are a 5mm and 6 mm Allen wrench

I am assuming you are talking about the castor wheels. You just need to remove the center bolt/axle. You will need a 5mm and 6mm Allen wrench. Once you get the screw out of one side, you should be able to push the axle out and drop off the tire for maintenance. This is generally a solid tire.

Time for new batteries.

More information would help...cheers

If you connected the voltmeter correctly and you get a negative reading then the batteries have flipped polarity.Get an automotive battery charger...preferably a NON automatic kind and charge each battery separately. Before you take them out of the chair...run both batteries completely down. Connect the charger correctly and charge normally. It will take a longer time to charge that way because the polarity has to change back. Test the batteries again using a correctly connected voltmeter . If the reading is back to positive then you're ok. If not then trash the batteries and get new ones. Radio Shack carries the correct batteries and are much cheaper than buying them from a chair service company

more info, make model, are the beeps in clusters (3 fast bleeps gap 3 fast beeps etc) any lights?

check to make sure the batteries are dud try to charge them one at a time with a car charger, if the same prob then replace batteries, if not and they charge fine replace the charger. always best to check first as batteries are not cheap,

NEED A SCHEMATIC OF FUSE NET WORK

Hello Sheila,download:SHOPRIDER SERVICE MANUAL 2007 1-800-743-0772,as a PDF File & if you are repairing anything yourself.Remember to take a photo via your mobile on every step,i say it is best way to work.Then you can go back to check,have a nice day.I hope this was of good help,Colin

Mine has 1 nut and I just rang an engineer and they told me for mine (mercury m48) it should definately come off once the 1 nut is removed and if it doesnt its ageing and rust. He said what he does is turns the scooter on its side, turns the wheel hammering it until it breaks free of the rust