iRobot Roomba 4210 Bagless Robotic Vacuum - Answered Questions & Fixed issues
Side brush will not stay on
The only way I can imagine the side brush not staying on is if the screw that holds it on is missing. Find a similar replacement screw. Did you get a package of replacement parts with your's? I did with mine, but I bought it many years ago now. While that brush is off, unwind all the thre4ad and hair that's wrapped in that section The brush will turn more easily without that all packed in there.
Why roomba clean for 2 minutes then returns to dock?
I suspect the battery is about dead. It keeps coming back for more power.
Run it away from it's charger, force it to run until it dies. Put it onto it's charger and let it charge a long time (Solid green light). Then run it again till it dies and repeat. This will perhaps force the battery to develop a longer memory
8/14/2014 2:31:02 PM •
iRobot Roomba...
•
Answered
on Aug 14, 2014
•
2,153 views
Why does roomba keep docking?
It needs to recharge every time it docks.
I would suggest that you let Roomba run out of the room where it's charger is. Then force it to run until it dies out. Then put it back onto it's charger.. I suspect that it's developed a memory (short) for charging and you need to force it to totally drain down, then charge for a good while. This should force it to develop a "Longer" memory. Works for me anyway.
Roomba 4210 won't start
Lift Roomba off the floor and place it in the center of the room and restart the clean cycle.If Roomba did not resume cleaning, lift Roomba and turn it over.* Inspect the Side Wheels for dirt or obstructions.Test the Side Wheels by pushing them in and out and making sure they rotate freely. Place Roomba in the center of the room and restart the clean cycle.
When the battery need to be replaced in 4210 roomba
Change the Roomba battery when the battery does not seem to get charged well or drains off too quickly or if you feel the roomba is not cleaning well. Its then the time to change the irobot roomba battery.Make sure you buy a
good quality Roomba battery form Battery Manufacturers only. bbmbattery stocks all batteries and also manufacturers batteries upon requirements. If you donot find the battery you need ask them. They can get you any battery you need.Thank you.
Brush cleaning, wheel thump
rchu is exactly right. No need for a complicated disassembly. If you have never pulled off those end bearings/caps, the hair may be very impacted, but removing it should solve the problem. The instructions will tell you by color (yellow for mine) which pieces come off for cleaning. Be sure to remove all such pieces. If the fit seems tight, it's probably because a lot of stuff got stuck in there. Be gentle but firm, and things the should come off will come off. Once you've cleaned all the pieces, the thumping should be gone.
I have a Roomba 4200
Yes the docking station is bad, and don't connect the 24V directly to the battery, it will burn it up.There is resistors in the docking station that might have change values. The voltage should be just a little higher then the battery.
I noticed my run time was getting shorter and
To extend Roomba's battery life and keep Roomba cleaning at peak
performance:
• Always keep Roomba plugged in when not in use.
• Recharge Roomba as soon as possible. Waiting several days to
recharge Roomba can damage the battery.
• For storage off the charger, remove the battery from Roomba and store
in a cool, dry place.
• Blue or black batteries should be stored after Roomba has been
used.
• Yellow batteries should be stored after being fully charged.
16-Hour Refresh Charge
If Roomba has been left off the charger for an extended period, Roomba
will initiate a special 16-hour charge cycle. This extensive charge
refreshes Roomba's battery and extends the battery life. While charging,
Roomba's "Clean" button will pulse quickly. Note: For best results, do not
interrupt this Refresh Charge.
Happy Holidays
The FixYa Team
After installing a new
Ok. What I would do is to disassemble the Roomba, clean both its wheels, Cleaning Head Module (including the gears) and the front bumper sensors. If after cleaning the front bumper sensors and same problem...you will need to replace the sensors. It's more than likely one or more of the IR LED are damaged.
Roomba model 4210 starts and
Inside this Roomba, the cleaning head module is clogged badly with debris. Open up your Roomba and remove all debris.
Not finding what you are looking for?