Bosch 18 in. SRS45E02 / SRS45E08 Exxcel Slim-Line Free-standing Dishwasher - Page 7 - Answered Questions & Fixed issues
Bosch e24 error code
It means that the dishwasher is not draining properly due to the drain filter being blocked
2/2/2021 5:29:28 PM •
Bosch...
•
Answered
on Feb 02, 2021
•
217 views
Bosch Dishwasher SHE43C cycle takes too long
Domestic dishwashers work by taking cold water and soaking the dishes as the water warms. Then it gives a good wash at high pressure, drains, refills, rinses and then hot rinses to dry.
If it is slow because of slow filling, check the water pressure and also clean the strainer filters on the supply hoses where they go into the machine.
If you want speed, buy a small under-counter commercial machine. They fill with hot water, have a tank heater and a rinse tank heater and the whole cycle is 3 1/2 minutes. Glasses first, plates and cutlery next, and pots and pans last.
Seems to be a known issue!! Videos here with solutions
https://www.google.com/search?q=Bosch+Dishwasher+SHE43C+cycle+takes+too+long
..
12/12/2020 12:22:06 AM •
Bosch...
•
Answered
on Dec 12, 2020
•
124 views
Display has error code h01
h:01 means 1 hour delay. Press the delay button repeatedly to get to h:00 then hit start.
9/16/2020 12:13:14 PM •
Bosch...
•
Answered
on Sep 16, 2020
•
68,426 views
How to clean bosh dishwasher inlet water filter
Most of these units have a waterproof solenoid inlet on the hose. If yours has this you can pull out the rubber washer in the end revealing a plastic mesh cover. This can also be pulled out with pliers. It can be a bit stiff to take care not to muller it!
Under the plastic mesh is also a restriction valve which helps to slow the water pressure down. This has a little plastic shaft with a small rubber seal around it and can also be pulled out and cleaned.
3/4/2020 7:35:35 AM •
Bosch...
•
Answered
on Mar 04, 2020
•
454 views
Bosch dishwasher E14 fault
Water protection system activated.Turn off water supply. Call customer service and quote the fault code.https://finderrorcode.com/bosch-dishwasher-error-codes.html
3/3/2020 11:11:55 AM •
Bosch...
•
Answered
on Mar 03, 2020
•
949 views
Just installed a new control panel on my bosch dw silence plus 44-dba and no lights on display panel come on,i have tried all power sources to the unit and all have power the door latch seems to be ok
Hello. The control panel most likely wasn't the problem...the main control board probably was blown out causing the user interface to remain off. What was the unit doing or not doing that made you replace the control panel?
BIG TIP--if you had a power interruption (such as lights dimming in the house--called a "brownout") or a full scale outage where the clocks reset, the main board very well could have been damaged by the current surge when the power came back on. *NORMALLY**, if the appliance wasn't damaged immediately, 4-6 weeks after the event, strange things will start happening or not happening with appliances because chips on the the board were damaged and start to fail. I tell all my customers to check into WHOLE HOUSE SURGE PROTECTORS--you can buy them at Lowe's or Home Depot and, your power company might install them on your house for a little extra on the bill each month--money well spent!
1/23/2020 5:47:22 PM •
Bosch...
•
Answered
on Jan 23, 2020
•
328 views
Not finding what you are looking for?