20 Most Recent Bosch 18 in. SRS45E02 / SRS45E08 Exxcel Slim-Line Free-standing Dishwasher - Page 8 Questions & Answers

0helpful
4answers

Bosch dishwasher stopped working after few minutes. And LED displayed E:24. What is the problem?

Fault Code E24 Symptom: Dishwasher not draining properly. Cause: Drain filters blocked. Action: Clean the filters. Go to:Why is My Bosch Dishwasher Not Draining? For more detailed codes see ... http://www.drdishwasher.com/troubleshooting/manufacturer/bosch/error-codes
5/18/2019 8:15:17 PM • Bosch... • Answered on May 18, 2019
0helpful
1answer

My bosch classic xx dishwasher has an error code E04. What do i need to do to resolve this?

You can google your question for answer About 15,800 results (0.65 seconds) Took about 2 seconds to find answer. Look in the instructions that came with unit. ttps://bosch-dishwasher-errors.com/bosch-dishwasher-error-code-e04/
5/18/2019 5:34:12 PM • Bosch... • Answered on May 18, 2019
0helpful
1answer

The container that has the dry dishwashing powder does not open during the washing cycle

John, you might have a problem with your dispenser mechanism. You can remove it from the door and inspect it to make sure the door spring and tripping mechanism are not damaged. If any of these items are damaged, you can buy them separately and save some money. If you can't trouble shoot these or the main unit mechanism is damaged, you just replace the complete unit. It is not difficult to replace the complete unit. This YouTube video can help. https://www.youtube.com/watch?v=MDideDjjuEU Good luck.
5/14/2019 1:09:57 AM • Bosch... • Answered on May 14, 2019
0helpful
2answers

Bosch dishwasher intermittently not completing cycle, not draining

it maybe something as simple as the door opening during the cycle - thus pausing the machine - this can happen when the machines with plastic tubs get hot - the top of the machine flexs a bit and the latch disengages and the machine stops. Next time it does it just try to push the door closed and hit start and see if it picks up where it left off. A stiffener is needed to repair the fault - but we have fixed with shims in a pinch - between the counter top and the dishwasher to minimize the flex
5/11/2019 4:44:52 AM • Bosch... • Answered on May 11, 2019
0helpful
1answer

Bosch sgs3002 dishwasher soap dispenser will not latch

The only thing you can do is replace the dispenser - not a difficult task
5/11/2019 2:46:36 AM • Bosch... • Answered on May 11, 2019
0helpful
1answer

Bosch she56c05uc display doesn't light up and will not turn on.

If the display wont light up but the flood switch works (drain pump operates) then its most likey the Power module (right side rear) is faulty. You might want to try a reset - at the breaker disconnect for a few minutes then try again
5/11/2019 2:38:37 AM • Bosch... • Answered on May 11, 2019
0helpful
3answers

GOOD AFTERNOON i HAVE A

Hello,

Welcome to FixYa.

Based on your description
I'd say the issue actually is with the control...unfortunately. This is
likely within the electronic timer/control, specifically the heater relay solder joint. ( a faulty flow switch, ntc or heater can also cause this, but not very probable ).

If you feel capable of checking this on your own, there`s a way to visually inspect the control yourself...it really isn't very complicated.

It will require you to remove the control from the unit and then remove the control from it`s plastic housing and look for a burnt solder contact on the printed circuit board.


dabfa62.jpg

The culprit will 99% of the times be one of the pins from the heater relay,hence the unit sit`s and takes longer & longer to finish because it can`t heat to advance or unless the 2 buttons for "cancel" are pressed...this can also manifest as a long cycle time as I mentioned and eventually display's "1" on units with a display and usually very poor cleaning, no heating ( don't be fooled by the homes inlet hot water temperature ) as a result.

You can also run the unit through a regular or econo cycle ...any cycle with the exception of rinse & hold, and with the door panel removed place an ammeter on the gray/black wire it should draw 11 amps during the wash cycle...after it fills and the flow switch indicates it has adequate water to engage the heater.

i.e. ( this may differ from your specific model, but the same rules apply )

f57273b.jpg
**My Opinion - if you or someone you know is proficient at soldering, a lot of times it can be remedied by simply repairing the solder...but it has to be done well...or it will not last.
Bosch recommend`s replacing the control and I don`t pretend to speak on their behalf nor do I profess to know better. This is just my experience (it work`s) and my opinion (why buy new if one can repair ?)

**Please disconnect the power or turn off the breaker before attempting any service to the dishwasher.**

Thank`s for visiting "FixYa" for your repair inquiries. Please take a moment and rate this solution to it's helpfulness. Good luck.

Regards,

Macmarkus :)
5/7/2019 11:11:46 PM • Bosch... • Answered on May 07, 2019
0helpful
2answers
0helpful
3answers

My Bosch dishwasher makes a terrible noise intermittently throughout the cycle. Cleans dishes fine.

Check impeller in pump for foreign object
5/3/2019 8:23:46 AM • Bosch... • Answered on May 03, 2019
0helpful
1answer

I would like to know the dB level of my bosch shu43c05uc/17. I need to replace it and want something at least that quiet.

Most late dishwashers range between 40 and 50 dB. That is equivalent to the ambiant noise of a library room.
5/2/2019 5:15:38 PM • Bosch... • Answered on May 02, 2019
0helpful
2answers

Bosch dishwasher S10R1B Hi, we have

Most cleaning problems are caused by the dishwasher not getting enough water. Filmes Online HD
4/13/2019 2:09:02 PM • Bosch... • Answered on Apr 13, 2019
0helpful
2answers

My Bosch dishwasher is not dissolving the tablets now! Any causes?

Try cleaning the pressure chamber and sump hose, if not this , it is not heating ( heater or pcb)
4/3/2019 1:28:36 AM • Bosch... • Answered on Apr 03, 2019
0helpful
1answer

Bosch SGV46M13GB dishwasher - tablet dispenser not opening error code showing S shape with arrow heads top arrow pointing east bottom arrow pointing west

The symbol you're describing is saying the salt tank is empty. Normally on this model if the dispenser isn't opening it's because it's not heating, the dispenser is triggered when it reaches a set temperature
3/14/2019 6:06:33 PM • Bosch... • Answered on Mar 14, 2019
0helpful
2answers

Where can I buy parts for a Bosch dish wash machine SGS60028S/01?

Where can on my phone at?
3/5/2019 6:27:12 PM • Bosch... • Answered on Mar 05, 2019
0helpful
1answer

Bosch classic xx dishwasher door won’t close but the cycle runs can anyone help

Door lock is jammed on , take front panel and console panel off , with a screwdriver, flick door lock mechanism to open, spray with wdr0 and it should work
3/4/2019 10:15:23 PM • Bosch... • Answered on Mar 04, 2019
Not finding what you are looking for?
Bosch 18 in. SRS45E02 / SRS45E08 Exxcel Slim-Line Free-standing Dishwasher Logo

73 questions posted

Ask a Question

Usually answered in minutes!

Top Bosch Dishwashers Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1482 Answers

Oloyede Monsuru

Level 3 Expert

1468 Answers

Michael Thomas
Michael Thomas

Level 3 Expert

3056 Answers

Are you a Bosch Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Bosch Dishwashers

  • Bosch Dishwashers

Most Popular Question

dishwasher not fill water

  • Dishwashers
Loading...