20 Most Recent
Bosch 24 in. SHX46A05UC Built-In Dishwasher - Page 9 Questions & Answers
Bosch dishwasher arms not spinning
Hmmmmmmmm. If the water goes in and the pump starts yet there is no washing action I would suspect that you have an impeller failure. The impeller on Bosch dishwashers is a two piece unit and the plastic rivets slowly dissolve until he impeller fails in 2 pieces. The fix is a new impeller which is supplied with a new seal as well. I believe Bosch does this to avoid running so long without renewing the seal and having a leak. I can't think of any other reason to have a dishwasher soluble part for an impeller. It's a bit of a bit** to fix but there are good videos on utube.
11/16/2019 1:53:35 PM •
Bosch...
•
Answered
on Nov 16, 2019
Alarm e15
Bosch SMS Series Dishwasher Fault Codes
E15
Water in base
Float sensor in the base has been activated. You can try to empty the base and restart the dishwasher as you will find noted many times in the forums but, if there is a leak this error code will simply be displayed again, you must find the cause of the leak.
but if you have a different model it can be something else
10/15/2019 1:21:25 PM •
Bosch...
•
Answered
on Oct 15, 2019
Bosch dishwasher stuck on auto
Try unplugging your dishwasher for 15 seconds or more, and then plug it back in. If that doesn't fix the problem, or if the problem comes back within a day, then you probably have a bad control board, or else the Auto key is stuck closed (like it is pressed).
10/3/2019 6:06:53 AM •
Bosch...
•
Answered
on Oct 03, 2019
I have a bosch dishwasher error code says watertap
It means that water is not getting to the dishwasher. Make sure your water valve is turned on all the way. If that's okay, then maybe your water supply hose got kinked when you pushed the dishwasher back in it's place. As a final check, turn off the water, disconnect the water supply hose at the dishwasher, and with the end of the hose sticking in a tall bucket, turn the water valve back on. You should have a good strong flow. If not, then your water valve (under the sink) is bad, and you will probably need to call a plumber, because the problem is not in your dishwasher.
8/17/2019 6:08:45 AM •
Bosch...
•
Answered
on Aug 17, 2019
HOW DO i RESET A BOSCH DISHWASHER MODEL SHE56T55VC/02 THAT IS STUCK ON AUTO 2:02
First, I'm not a BOSCH tech.
I just installed an ELECTROLUX dishwasher last month and had a similar problem. We also have an older Kenmore dish washer in another part of the house. The Kenmore is at least 15 years old and the touch pads are very soft and easy to select. The new one did not select either. I have to firmly depress the pad (which seems to be a stiffer plastic) and make sure I'm pressing down on the right spot to get things to work.
* I recently came across the same problem. Pressing buttons won't change the displayed setting and it seemed to be 'stuck' in one mode but I coudn't tell if it was in between a cycle or just stuck. I've found that holding the 'start' button down (firmly) for 10 seconds will cancel all functions and it went back to normal. Since then it gets stuck several times over the week. I don't know if one of the kids is opening it up as I only turn it on at night just before going to sleep. So, someone may be sneaking around for a mid nite kitchen raid.
* If you still have problems then check your warranty as many of these machines have parts warranty for 3-5 years. The 'switch' section if bad must be completely replaced as it is all one piece. These membrane switches will get damaged from a sharp fingernail or using a knife or fork to force the button down. (happened with the Kenmore, Kids kept stabbing it to get it to turn on.)
Aloha, ukeboy57
5/31/2019 4:29:09 PM •
Bosch...
•
Answered
on May 31, 2019
Not finding what you are looking for?