20 Most Recent Bosch SHY56A02 / SHY56A06 Built-in Dishwasher - Page 4 Questions & Answers

Bosch describes it as being 'painted stainless steel'. https://www.google.com/search?q=bosch+shu43c05uc/22+parts+diagram .. .

You have an issue that no one has yet encountered! Try squirting Toilet Duck Toilet cleaner in there. Wait an hour and then shoot it with a pump sprayer set to spray a jet of water. The toilet cleaner is bleach based gel and should stick and loosen the gunk.

POSSIBLY THE DOOR LOCK IS BAD

Hi Jane, water in the bottom of the dishwasher results from clogs in the filter or in the drain hose. Please make sure that you have disconnected the appliance from the mains before cleaning the filter! If your dishwasher is displaying an error code please check the meaning of the error message. https://www.justfixed.co.uk/bosch-dishwasher-error-codes/ Good luck Best, Dave

Hey Karen, Water in the bottom of the dishwasher results from clogs in the filter or in the drain hose. Before you do any work on your dishwasher, make sure that it's switched off at the mains. If cleaning your filter hasn't resolved the issue, then the next thing that could be preventing your dishwasher from draining is a blocked drain hose. Is your dishwasher displaying an error code? If you see the E25 error code on a Bosch dishwasher, that means the filter is blocked or clogged, and water cannot drain out of the machine correctly. You can check all Bosch dishwasher codes here: https://www.justfixed.co.uk/bosch-dishwasher-error-codes/ Good luck! Best, Dave, Just Fixed

Direct from Bosch or from RepairClinic.

Spare Parts Finder ' Bosch Home Appliances

https://www.bosch-home.com > cleaners-accessories > s... To view a list of parts for your appliance, enter its Model Number (E-Nr) below. If you already know your Model Number, just enter the first few characters. did you try a reset? https://www.google.com/search?q=BOSCH+dishwasher.+E-NR%2C+SMS6062%2F01 ..

I assume your using steel hoses. If not, you should be. The washer inside can be worn. Replace washer. Use. Teflon tape on threads. Over tightening can cause leaks. Buy new hoses.

Usually when a capacitor for a start / run function on an AC motor fails, you will hear a buzzing sound from the motor and it will cause the motor to overheat.

The hinges are out of line.

Is there an error code or lights present when it stops?

A malfunction has occurred. You won’t be able to fix this problem.

I have been told to replace the timer which I am looking to do the same to my machine!

For Bosch Dishwasher Ascenta models, open the door to reset it. Hold the Start-Reset button for about 5 seconds or until the Active indicator turns off. Shut the door of the dishwasher to allow it to thoroughly drain before turning it off. This should reset the cycle drain.

Look on the rear where the power wire goes into the machine. Bosch think here, but they can't even get this right, click on the plus markers and the descriptions are reversed. https://www.bosch-home.com/us/owner-support/serial-number-finder/dishwashers This says the same, so it is likely that yours came off, or was removed. https://www.hunker.com/12002146/how-to-find-the-serial-number-on-a-bosch-dishwasher ..

A faulty cycle timer could be the culprit.

Did you check the leak sensor pan which is under the machine, but above the floor. Once it senses water in it, it stops the cycle. Google make model leak sensor ..

Very common"no heat" error for bosch to stay at 1 min. If the water doesnt get hot enough, it will never finish cycle

If you can connect to the circulation pump using a multi meter using the Ohm ? (resistance) setting, touching the 2 poles - and +, you can see if the motor is failing. If you get a current tester pen you can track the electricity along the wires to the circulation motor to see if the dishwasher is delivering power. If you remove the circulation pump you can have someone test it(by hooking it up to a direct power source). I had a similar issue and it was not the circulation motor, but the control board that failed.