20 Most Recent Bosch 24 in. SHU66C05 Stainless Steel Built-in Dishwasher Questions & Answers

0answers
0helpful
1answer

Door on Bosch shv46c03uc/14 falls down stainless

>> springs broken/too weak.get a service agent
10/18/2013 4:01:02 PM • Bosch 24 in.... • Answered on Oct 18, 2013
0helpful
2answers

Bosch Excell Dishwasher

drain pump is running all time. cause is a leak. remove bottom front panel and mop out water or can also tilt at 45deg and water shud run out. machine shud then run but you then hav to find leak
5/8/2013 9:19:28 PM • Bosch 24 in.... • Answered on May 08, 2013
0helpful
1answer

Where can I find a Bosch SHU66c05 service manual

https://portal.bsh-partner.com/portal(bD1kZSZjPTAwOQ==)/PORTALFRAME.HTMUse link, type in the full ENR and you can then download a PDF file of the manual
3/22/2013 1:41:57 AM • Bosch 24 in.... • Answered on Mar 22, 2013
0helpful
1answer

Bosch - Secondary hose on

Hello, jim I was trying to help you out here. Maybe this will help some? I was going back to some customers that asked questions in the past and it appeared that no one answered them, so I thought I would take some of my personal time to see if I can help. Even though this site may not have your exact model or brand, This link will help you tons. Here is a link to about everything you want to know about your dishwasher, from repair to trouble shooting it,pictures, video's. Just scroll around and you will see tons of information to almost any question you might have on your dishwasher. If you go to this link and click around, I am sure you will find out so much about your dishwasher, you will know more that the company that made it. Here Is the link for you to click on>> http://home.howstuffworks.com/dishwasher.htm Please if this helped you at all, if you can find the time to rate my help and some kind words written would be appreciated for my free help , I would appreciate it. Here is also my direct link to my own pages of other areas of my expertise for other problems you might have in Automotive,Appliance, and Electronics. Drop In anytime for my help. Thanks,Mike http://beta.fixya.com/users/mc1bean
10/27/2011 10:48:12 PM • Bosch 24 in.... • Answered on Oct 27, 2011
0helpful
1answer

I've had my bosch

This has to do with the detergent change that happened recently. Go to the link and it will explain what is causing this in more detail as well as how to get better results.

http://www.appliancerepairlesson.com/2011/02/24/dishwasher-is-no-longer-cleaning-film-and-debris-are-left-on-dishes/

Good luck

http://www.appliancerepairlesson.com
3/5/2011 5:04:57 AM • Bosch 24 in.... • Answered on Mar 05, 2011
0helpful
1answer

My glasses are coming out with a cloudy film on

If you have hard water, glasses can look spotted and cloudy even after cleaning. Sometimes changing the dishwasher detergent can help. The easiest solution to clearing up glasses that start to look cloudy is toadd some vinegar to the bottom of the dishwasher before you start a cycle. Simply add 1 cup of white vinegar and it will clear up your glasses very well.
You should see marked improvement after the first time you do this. If they are not crystal clear then simply repeat the process until all of the cloudiness is gone. In fact I recommend to using a little vinegar in each cycle to maintain the clarity of the glass.

Note: you can pre-test this by rubbing some vinegar on an individual glass with a cloth. If you cannot remove the cloudiness by soaking it and rubbing vinegar on it then it is possible that the glass is etched due to harsh or cheap dishwasher detergent and vinegar will not solve the problem.
3/2/2011 4:16:22 PM • Bosch 24 in.... • Answered on Mar 02, 2011
0helpful
1answer

It's not cleaning properly. e.g. leaving coffee

Hi,



I have an older dishwasher also and recently my wife also complained about it not cleaning right... so me being the man I am tried in vain to clean the things... Bought new spray arms online and installed them in minutes...now the thing works like new... However I have also found that if the heating element goes bad then that also can mess things up bad... So I would buy new spray arms, and also check out the heating element to make sure it is working... Here is a tip that will help you with the online buying...


Dishwasher
Spray Arms not Spinning

How to Buy
Appliance Parts Online

A bad heating element causes many problems in dishwashers...

Dishwasher Problems The
Heating Element not Working

Dishwasher Maintenance



Dishwasher Residue and Film on Dishes



heatman101
/[/[/[/[/[/[/[/[/[/[/[/[/[/[/[/[

2/22/2011 8:00:11 PM • Bosch 24 in.... • Answered on Feb 22, 2011
0helpful
1answer

Can turn off dw

Hello,

Welcome to FixYa.

Based on your description
I'd say the issue actually with the control...unfortunately. The "1" being displayed is actually an error code associated with a heating fault.


**B/S/H/ also issued a recall on certain models between 1999 - 2006 depending on the model & serial number, you can check with yours but to my knowledge the SHU66 series wasn't included for whatever reason, though it still suffers from the same problem...you'll need the serial number too. Here`s the link if you want to see for yourself **

http://microsites.boschappliances.com/safetyrecall/dishwasher/


As I've alluded to the issue is likely within the electronic timer/control, specifically the heater relay solder joint. ( a faulty flow switch, ntc or heater can also cause this, but not very probable ).

If you feel capable of checking this on your own, there`s a way to visually inspect the control yourself...it really isn't very complicated.

It will require you to remove the control from the unit and then remove the control from it`s plastic housing and look for a burnt solder contact on the printed circuit board.


dabfa62.jpg


The culprit will 99% of the times be one of the pins from the heater relay,

9f1823d.jpg

**Flip this over and inspect the solder joints, it will be obvious when you see it.**

This ones new, but it's where to look...

9119d99.jpg


...hence the unit sit`s and takes longer & longer to finish because it can`t heat to advance or unless the 2 buttons for "cancel" are pressed...or takes a long time as I mentioned and eventually display's "1" on units with a display and usually very poor cleaning as a result.

You can also run the unit through a regular or econo cycle ...any cycle with the exception of rinse & hold, and with the door panel removed place an ammeter on the gray/black wire it should draw 11 amps during the wash cycle...after it fills and the flow switch indicates it has adequate water to engage the heater.

i.e.

f57273b.jpg
**My Opinion - if you or someone you know is proficient at soldering, a lot of times it can be remedied by simply repairing the solder...but it has to be done well...or it will not last, although Bosch recommend`s replacing the control and I don`t pretend to speak on there behalf nor do I profess to know better. This is just my experience (it work`s) and my opinion (why buy new if one can repair ?)**

**Please disconnect the power or turn off the breaker before attempting any service to the dishwasher.**


If you do not feel comfortable attempting this service, call a local pro, preferably one familiar with Bosch/Thermador/Gaggenau/Siemens, to service your machine.

Hope this answer`s your question, let me know if I can assist you further.
Thank`s for visiting "FixYa" for your repair inquiries. Please take a moment and rate this solution to it's helpfulness.

Good luck.

Regards,

Macmarkus :)
12/25/2010 7:49:02 PM • Bosch 24 in.... • Answered on Dec 25, 2010
0helpful
1answer

My 5 year old bosch

Hello,

Welcome to FixYa.

Based on your description
I'd say the issue actuallt is most likely with the control...unfortunately. The "1" being displayed is actually an error code associated with a heating fault. I wouldn't feel very confident in the repair person you had if they did not know this.

Bosch has had a history of this exact problem I'm about to lay out for you and this is the first thing I'd be looking for if called out to service the unit with the symptoms you've described.
**B/S/H/ also issued a recall on certain models between 1999 - 2006 depending on the model & serial number, but it shouldn't apply to yours....based on just the model number, but double check as well as check the serial number. The issue was directly related to the heating circuit (specifically the heat relay on the control) Here`s the link if you want to see for yourself **

http://microsites.boschappliances.com/safetyrecall/dishwasher/


As I've alluded to the issue is likely within the electronic timer/control, specifically the heater relay solder joint. ( a faulty flow switch, ntc or heater can also cause this, but not very probable ).

My first suggestion would be contacting Bosch re: the recall or calling in an authorized bosch service tech. if that is an option for you and your budget however, If you feel capable of checking this on your own, there`s a way to visually inspect the control yourself...it really isn't very complicated.

It will require you to remove the control from the unit and then remove the control from it`s plastic housing and look for a burnt solder contact on the printed circuit board.


dabfa62.jpg


The culprit will 99% of the times be one of the pins from the heater relay,

9f1823d.jpg

**Flip this over and inspect the solder joints, it will be obvious when you see it.**

This ones new, but it's where to look...

9119d99.jpg


...hence the unit sit`s and takes longer & longer to finish because it can`t heat to advance or unless the 2 buttons for "cancel" are pressed...or takes a long time as I mentioned and eventually display's "1" on units with a display and usually very poor cleaning as a result.

You can also run the unit through a regular or econo cycle ...any cycle with the exception of rinse & hold, and with the door panel removed place an ammeter on the gray/black wire it should draw 11 amps during the wash cycle...after it fills and the flow switch indicates it has adequate water to engage the heater.

i.e.

f57273b.jpg
**My Opinion - if you or someone you know is proficient at soldering, a lot of times it can be remedied by simply repairing the solder...but it has to be done well...or it will not last, although Bosch recommend`s replacing the control and I don`t pretend to speak on there behalf nor do I profess to know better. This is just my experience (it work`s) and my opinion (why buy new if one can repair ?)**

**Please disconnect the power or turn off the breaker before attempting any service to the dishwasher.**


If you do not feel comfortable attempting this service, call a local pro, preferably one familiar with Bosch/Thermador/Gaggenau/Siemens, to service your machine.

Hope this answer`s your question, let me know if I can assist you further.
Thank`s for visiting "FixYa" for your repair inquiries. Please take a moment and rate this solution to it's helpfulness.

Good luck.

Regards,

Macmarkus :)

11/22/2010 7:00:33 PM • Bosch 24 in.... • Answered on Nov 22, 2010
Not finding what you are looking for?
Bosch 24 in. SHU66C05 Stainless Steel Built-in Dishwasher Logo

93 questions posted

Ask a Question

Usually answered in minutes!

Top Bosch Dishwashers Experts

mark warfield
mark warfield

Level 3 Expert

453 Answers

David Shaub

Level 3 Expert

2994 Answers

Marvin
Marvin

Level 3 Expert

85241 Answers

Are you a Bosch Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Bosch Dishwashers

  • Bosch Dishwashers

Most Popular Question

glasses coming out cloudy film

  • Dishwashers
Loading...