20 Most Recent Bosch 23 in. SHU33A Built-In Dishwasher - Page 2 Questions & Answers

Hello their sounds as though water heater has failed if it doesnt heat it defaults to a 3 hour cold wash and never finishes cycle eg doesnt go through rinse stages.will need a new heater service tech to change as fairly complicated.

A solution to this problem would be to sell me your dishwasher. The law firm for which I work is looking to acquire an old unrepaired Bosch SHU 33 dishwasher for some ongoing litigation. If you (or anyone else with this model Bosch) could send me some details regarding your dishwasher, you may be able simply to buy a whole new dishwasher. My email is JFraser -at- jshlawmi.com.

Thanks!

Check whether water is flowing the flexible hose. Check the strainer attached to the hose at the machine end.

However try pouring water straight into the wash chamber and start the machine. If it works, it is the incoming water problem

Have you purchased a new food waste disposer for the kitchen sink area? If so, make certain if you are draining the dishwasher directly into the food waste disposer, that you have removed the plug from the food disposer. Or you may be correct that the water pump is inoperable due to an obstruction or basic malfunction. Contact an appliance service company.

Hello,

I think I know the pieces you are referring to and you can only install them one way. I can direct you to searspartsdirect.com and if you enter your model number you should have access to several breakdown illustrations of your d/w however, I`m here to tell you, don`t sweat it. Most illustration`s I`ve seen don`t even show them either.

Those two blocks ( which slide into the front of the hinge behind the door panel by the way ) can remain left out without any functional consequence to your dishwasher. In fact the regional training representative for north america used to joke with us techs how he had a collection of them from tossing them into his toolbox instead of putting them back in place. They do increase the structural support of the front panel, but unless you plan on moving it around frequently, I wouldn`t worry about it.

If you are still concerned, post back with your email and I can send you a complete repair guide in "pdf" format for your dishwasher.

Hope this was helpful to you. Thank you for coming to "fixya" and please let me know if I/we can assist you further in this matter. Please take a moment and rate the info I provided for you here today.

Good luck.

macmarkus :)

uou must replace the module control. some of those control are covered under the recall at bosch.call bosch or go to thermador .com they are the same company. hope this helps.

you probably have something stuck in your drain propeller or circulation pump. let me know if this helps.post a 4 thumbs post

change the control module. check to see if there is a recall on this module. bosch will tell you if it is.give them model # and serial #. by the way if the modell is arecall you will get a free fix. let me know if this info helps,

the motor may have wate in it get it checked

no fuse but it does have a reset breaker under the front panel to the left

I got answer from previous post on your site by 'boeschbrady'.Person had same problem,also said part was under Warranty. we called the store where unit was purchased and my unit is also under Warranty "less than 5 years old' repair man is coming next week.Thank you for a
great site Patee

your dirty water backed up into the washer (which it shouldn't do) and probably clogged something in there,..i would recommend getting it flushed out somehow, not sure how,.....next time, your washer drain hose should go up under the sink as high as possible and then back down to drain,....this settup makes it hard for drain water to go back into washer,....it's instructed in any dishwasher manual

change timer

the first thought that comes to mind is the valve... are you sure the water valve to the dishwasher is open?

The next possible cause could be a bad relay switch which opens when the unit calls for water... if it's bad the switch will stay closed and it won't fill up

Sometimes when the unit is brand new it may take several tries before it starts pumping water thru because the line needs to purge.

could also be a severe kink in the water supply line from the valve...

i call a repairman in it was the drain pump thank you for your help NOT what a joke this site is have a good day boys

Try pouring in enough water to cover the screen in the bottom of the dishwasher, maybe a 2 quarts or so, then run the drain cycle. This should prime the pump and at least tell you wether the drain pump is working or not. Just a trick i've heard and worked for me, not my area of expertise however.

sounds like you are not getting enough or any water a check the water level when it fills... let me know