Bosch Axxis WTL 5410 Electric Dryer - Answered Questions & Fixed issues


yes if its plastic just pop it out to replace

Bosch Axxis WTL... • Answered on Apr 08, 2019 • 1,494 views


There is also another overheat module below the front door too. Check that. Also, forgive me for asking the very obvious, but have you checked the entire exhaust pipe to make sure that there is no restriction that would cause overheating.

Bosch Axxis WTL... • Answered on Mar 18, 2017 • 110 views


Cycle is interrupted and ''E1'' appears in display. Condensate hose is blocked in some way. Turn off dryer and check hose. Condensed water not pumped out (WTL 54 condensation models only). Pump failed. 25808741-gtkp3url2ghtdqenstp5bokb-1-0.jpg Dado

Bosch Axxis WTL... • Answered on Oct 20, 2015 • 190 views


Most Bosch dryers have a heater reset button behind the main rear panel. If this thermostat has tripped, there is a REASON, resetting it may make things work for a short time but your issue is bound to return. There are many other things to check on Bosch dryers to ensure proper air flow throughout the dryer and house venting. Pleazer Appliance...

Bosch Axxis WTL... • Answered on May 20, 2014 • 584 views


this is normal operation it turns the drum one direction then the other this is because of the way it condensates

Bosch Axxis WTL... • Answered on May 04, 2014 • 161 views


Check the little button that the door pushes in when you close the door (door switch).

Bosch Axxis WTL... • Answered on May 02, 2014 • 202 views


have you checked the vent line it could be stopped up if the line is bent same affect as the lint filter being full

Bosch Axxis WTL... • Answered on Jun 02, 2012 • 2,259 views


Hello folks try this if you have not gotten this resolved. Your dryers have 2 sensor systems, the first one test the clothes for moisture, the second for the heat. The 1 sensor system drops resistance when the wet clothes are put in the dryer. the shutting down after 5 minutes and lint filter light coming on could be that the dryer isn't sensing the moisture. Now for the fun part, the entire inside of the drum and paddles is the moisture sensor. Try cleaning the inside of the drum with a cleaner to remove any detergent or fabric softner residue. This is crucial if you are using fabric softner sheets as they coat the drum. Also wash the lint filter with soap and water so the water goes straight thru instead of puddling up. Remember to also clean the condenser as this can trigger this issue as well. Hope this helps

Bosch Axxis WTL... • Answered on Oct 05, 2017 • 553 views


This code indicates a problem with the dryer's heating system. The code will appear when the heating circuits are broken or when there is an intermittent break in the power source for the dryer. If the heating circuits are working and the power source is steady, you may need to replace the central control board.

Bosch Axxis WTL... • Answered on Jan 09, 2012 • 901 views


Hi,Here is a tip that I wrote about dryers and noises...It will help you determine what is happening there...Dryer Repair Squeaks, Grinding, Clicking and Knocking Noiseheatman101 Asker's Testimonial "That answer was very informative - thank you fortaking the time to educate me. " - teresa241964

Bosch Axxis WTL... • Answered on Aug 24, 2011 • 49 views


Hello, welcome to FixYa.

I'll start by saying your post indicates it is a Bosch dryer, however if you could varify and post the model number is indeed a WTL5410, (meaning it is a condensor model-none vented) I can speak directly instead of generalizing.


macmarkus_849.jpg


Also can you clarify what it is you mean by "dryer vibrates and rotates during use" I think I can determine what may cause the vibrating, but what do you mean by rotates ? It should obviously rotate the drum, so I presume you don't mean that.

The vibrating quite often can be caused by several factors such as a loose blower wheel, a wearing drum bearing, as well as dirty drum glides.

Let me know as much as you can and I'll try to assist you going forward in any way I can. I do have the service manuals for these machines (if it is indeed the WTL series Bosch) if you'd like to provide an email address in your reply I can attach it to an email for you.

The service manual is approximately 5.5MB and is "pdf" format.
Regards,

Macmarkus :)

Bosch Axxis WTL... • Answered on Aug 23, 2011 • 95 views


Hi,

If your dryer is not drying like it once did or if you just have nottaken the time to give yourself a clean dryer in a long time then youneed to do that. At least once a year the dryer cleaning should takeplace. Lint build up in the dryer duct is one of the main causesfor your dryer to fail.

Here is the rest of this tip about DryerMaintenance

heatman101

Bosch Axxis WTL... • Answered on Aug 15, 2011 • 79 views


Was the motor tested and it passed?

Bosch Axxis WTL... • Answered on May 13, 2011 • 98 views


Hello,

Welcome to FixYa.

Based on what I've read of your post...I'd suspect the hi-limit thermostat is tripped if it is indeed a WTL series Bosch.


I'm not clear as to whether or not you located the hi-limit safety, reset it, or ruled it out so I'm going to explain what to look for and what to do when you get there.

**Unplug the unit from the wall or switch off the breaker...safety first**

Once the dryer has been disconnected from any power, remove the rear panel...

i.e.

7209371.jpg
Once the panel has successfully been removed, you'll see the heater with the Hi-Limit and NTC attached. The Hi-limit is the thermostat with the red button in the center...

i.e.

03efa1a.jpg
push it in to reset it. As you can see by the images I've provided, if you have a multi-meter or ohm meter you can verify the proper values of the listed components.

If the hi-limit is tripped, obviously something triggered it, you can check the possible culprits such as the NTC's or heater with the info I provided above as I alluded to.

( Even so, I'd suggest running it through a cycle or two and monitor it's performance, it may have tripped simply due to poor air flow from a large load etc. and therefore nothing is actually wrong...human error )

You may run the dryer momentarily without the rear panel in place provided nothing electrical has been disconnected, don't attempt an entire cycle, just witness the heater functioning, but it isn't recommended for much longer than a minute or two.

Thank you for choosing FixYa and please let me know what you find out or if you indeed require further assistance. Good luck.

Regards,

Macmarkus :)

Bosch Axxis WTL... • Answered on Oct 14, 2011 • 1,475 views


This type of diagnosis will require accessing the internal components & making voltage & resistance checks with a volt/ohm meter. There are several different components that could cause this symptom & yes it is possible that the door switch is bad. This model of dryer should only be worked on by an experienced, trained technician due to all of the electronic controlled parts. richroth_121.jpg

Bosch Axxis WTL... • Answered on Mar 20, 2011 • 717 views


I have the same issue with my bosch.Did you replace the board?

Bosch Axxis WTL... • Answered on Mar 03, 2011 • 282 views


Clean heat exchanger.

Check air inlet to make sure it is not blocked.

Bosch Axxis WTL... • Answered on Feb 08, 2011 • 631 views


Remove the panel in the back of the dryer that covers the heating element. ( the inner panel) (part that sticks out). Once that panel is off you will now be able to see the heating element and the thermal sensor. the reset button is located on the thermal sensor.

Bosch Axxis WTL... • Answered on Feb 08, 2011 • 317 views


Open the bottom front panel. Remove the heat exchanger. Take notice to see if theres any water in that compartment. Reach your hand towards the back of that opening to see if there is water pooling back there. If theres water present, then your condensation pump needs to be replaced.
also double check the connection of the drain hose from the dryer to the drain.

Bosch Axxis WTL... • Answered on Feb 08, 2011 • 928 views


Open the front panel, remove heat exchanger and clean. also clean out lint tray. this might help a little. Now lets check if the thermal sensor or heating element needs to be replaced.
Unplug the dryer. remove the panel in the back of the dryer that covers the heating element. ( the inner panel). On top of the heating element you will see a thermal sensor with a small red button on it. Thats the manual reset button. To test if the heating element is working properly you can disconnect the wires from the sensor and clip the connectors together . Plug the dryer back in and start it. pay attention to the heating element. It should begin to glow shortly. if it doesn't then your heating element is bad and needs to be replaced.

Unplug the dryer. Connect the wires back to the thermal sensor. Plug the dryer back in. Before you start the dryer, press the red button on the thermal sensor. Start the dryer. If the heating element doesn't come on and dryer doesn't heat, then you need to replace that sensor.

Bosch Axxis WTL... • Answered on Jun 21, 2013 • 1,002 views

Not finding what you are looking for?
Bosch Axxis WTL 5410 Electric Dryer Logo

117 questions posted

Ask a Question

Usually answered in minutes!

Top Bosch Dryers Experts

Cindy Wells

Level 3 Expert

6259 Answers

Lawrence Oravetz

Level 3 Expert

10548 Answers

Vernon Taylor

Level 3 Expert

7446 Answers

Are you a Bosch Dryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...